Get complete information related to latest Ms Structural Steel Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Ms Structural Steel Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Ms Structural Steel Tenders.
Tender For corrigendum : : supply, installation, testing & commissioning of electrical equipment for dg block 119a of inrp - ht panels (119a)supply, installation, testing & commissioning of indoor type floor mounted, single front, metal clad, 1250 a, 6.6 kv, 3 phase, 3 wire, vcb switchgear panel suitable for a short circuit current of 31.5 ka for 3 seconds, internally arc tested for 31.5 ka for 1 second, comprising of following incoming & outgoing feeders : incoming feeder: 1 no. 1250 a, 3p vcb outgoing feeders: i) 7 nos. 630 a, 3p vcbii) 1 no. 1250 a, 3p vcb as tie feederwith surge arrestors, relays, pts, cts & other necessary accessories including associated structuralsteel required for complete installation of the panel & equipment earthing of the panel from both the earthing terminals of the panel to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings. reference drg. nos: ip1/119a/05027339/dwg/001/r0 & ip1/119a/05027339/dwg/002/r0(note: terminal box of each incomer of 6.6kv switchboard shall be suitable for terminating 4x3cx400 sq.mm., 6.35/11kv (e), a2xwy cables.), supply of spares for ht panels as per attached spares list mentiond in section c, part ii of tender, 2.5 mva, 6.6/0.433 kv dry type transformers (119a)supply, installation, testing & commissioning of 6.6/0.433 kv, 2.5 mva, dyn11 dry type cast resin transformer having percentage impedance of 8.5% complete with ht cable end box, lt bus duct flange, off load tap changer on ht side with range of +/-5% in steps of 2.5%, wti scanner, ct for restricted earth fault protection and other necessary accessories including associated structuralsteel required for complete installation of the transformer & equipment & neutral earthing of the transformer from both the earthing terminals of the transformer to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings.reference drg. no. : ip1/119a/05034347/dwg/001/r0, supply of spares for dry type transformers as per attached spares list mentiond in section c, part ii of tender, 2000 kva diesel generator sets (119a)supply, installation, testing & commissioning of 3 phase 2000 kva prime power 433v, 50hz, 0.8 p.f. diesel-generator sets with 110% overload capacity for 1 hr with four (4) stroke inline or vee type cylinder arrangement having engine speed 1500 rpm, 24v electric battery starting system with a provision of interchangeability of battery bank between two dg sets, complete with all auxiliary equipment including amf control panel, auxiliary mcc panels, heat exchanger cooling system, raw water pump, remote radiator with fans on terrace, ms exhaust piping, exhaust structure (maximum 30 m stack), 4 nos. of 3.6 cubic metre fuel day tank outside dg building (for all 4 dg sets) & 1 no. of 990 ltr intermittent tank inside each dg room, ms "c" class fuel piping between engine & fuel tank, dg room accoustic treatment & complete ventilation of dg room, brushless excitation for alternator, one no. 3200 amp 415 v 4p acb, msstructuralsteel supports/ channels/ angles & other necessary accessories including associated structuralsteel required for complete installation of the dg & equipment & neutral earthing of the dg from both the earthing terminals of the dg to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & necessary statutory clearances from cpcb etc. as required and as per tender technical specifications & drawings. design and construction of foundation for exhaust pipe rack/ structure of dg set is included in the scope of the contractor.reference drg. nos. : i) ip1/119a/05034347/dwg/001/r0ii) ip1/119a/05044831/dwg/003/r0iii) ip1/119a/05044831/dwg/004/r0iv) ip1/119a/05044831/dwg/005/r0v) ip1/119a/05044831/dwg/006/r0, supply of sp
Tender For auction sale of depot ferrous scrap - scrap miscellaneous m.s. cutting such as angle, channel, round bar, g.i. ducting with or without foam rubber, m.s. pipe with or without cement, gi insulator,hook ,mast multiple cantilever channel, cantilever assembly spsgi bolt,double eye distance clamp, guard box with or without wooden, air filter, plate (all type) frame, rod, ms sheet, plate, flate, tmt bar, c and w cutting, nut bolt, square bar, pin, g i rod, g i plate, box, gril, extended metal sheet, coupling, chain hook, shutter, bond strip, blower, battery box, electric box, shock absorber, all type of pipe, gi pipe, ms pipe, chain, chain pully, tikam, powrah, structure, platform structure, small rod pieces, strip, foundation, tank, sleeve, bearing plate, tensioning device, window, pannel, foot step, sheet, gear, mesh, screw coupling, stand, roller, cylinder, small auto parts, slack adjuster, hanger, link, hook, stay rod, brake shoes, coupler, adopter, cock, pick axe, beater, showel, clamp, stand, rail kaichi, rack ballast, electric pole wire support angle, fire extinguisher, rail dolly, all type of lorries with or w/o. wheels, rubber wheel tyre, tongue and other pwi tools, jali, angle frame, belly gater, coach washing machine, machine parts, rope wire,coach door,counter weight,gi insulator with porcelin,electric pole,elavator accessorires,wheel barrow,helmet,pan gamalah, various type of bucket, ms box, furnace, gear, various type lc & wl board of, silent block, wire basket, bucket g.i., track lifting jack, cable tray,m s chain,weigh scale, coach cutup material, empty barrels, empty drum,db grid mesh and hbac air filter etc. with or witout other ferrous and minor nf attachment old used and u.s.
Tender For auction sale of depot ferrous scrap - scrap ferrpus melting consisting of coach cutting parts, window & seat bearth frame, eq. stay, foot step, foot rest plate, m.s & g.i pipes & sheets, pipes fittings, fabricated structure wire & wire-rope, plane & twisted bar, shock-absorver & damper without cutting, shuckle stone, side frame- key, brake shoe head, brake beam, gear case, lower spring seat, bmbc cover, follen rod, bond - strip, protective tube, tirfor, rachet, pull lift,m.s. chain, nut, bolt,washer, cotter, locking plat , expended metal,u-type bracket,clamp,trd bracket, empty electric pannel, box, switch board, nos- plate, wheel barrow, pandrol clip, battery box, rack blast, crusible & its parts,broken helical- spring up to single coil, pipe &tie bar fancing, sig ladder, sig. box & othe various types items fit for melting released from carriage, sig., electric, trd, p. way, loco of shorts & sizes with steel, c.i. & neg. n.f. attachment if any. note- 1- loading by purchaser. 2- cutting allowed for loading purpose at time of delivery. 3-delivery not allowed against part payment. 4- other than melting items if found during cutting &loading will be seperated ¬ delivered to purchaser. location;-lying between line no. 10 and 11 in plot- g near tree- no. -g7
Tender For auction sale of acsr dog conductor,control cable,gi structure material,ms scrap,cables,copper pipe and 3-ph motor scrap,11kv reactor,isolator,transformer,transformers as per lot description,transformer-66 kv ct/ pt/la/kvt,220 kv bushing,battery set,misc aluminum scrap,empty oil barrel (unserviceable),post insulator with metal parts,disc insulator,fax machine
Tender For auction sale of depot ferrous scrap - p.l.no. 98057054. scrap melting gr-d consisting of cutting sol bar, fall plate, head stock, cutting outside panel, ceiling fan down rod, wagon door & body cutting part, driver seat assy. , trough floor, electrode holder, cab window assy. cyclostyling machine, trolley, plate cutting, angle cutting, iron axle with pipe, cover of tail light head light flasher etc, tie bar fencing, pipe cutting, structure cutting, cut pieces of rod, damage emu door, lubricating felt assembly frame, mvmt,tmb,emu, mvsi impeller, mvsi duct, air duct, fan chamber, electrical pillar box, compression spring of bk cylinder, inter/after cooler tube type, lid of grease drums, partition frame, cattle guard, ms base, l.t.pannel box ferrous, , tap changer, expanded metal, vsb packing, bs door, iron window, ms rod , fire extinguisher, gate, nut , bolt, washer, wick felt carriers, pin, angle frame with or without net, r.s. joint, ms iron plate, angle, door shutter, cutting chain, net box, fencing wire and such materials fit for melting gr-d, except p-way materials such as rail, fish plate and non ferrous etc. note-some items are attached with negligible quantity of ss. qty-80mt.location-west of 40 ton weighbridge, east of inner boundary wall. condition-two days advance cutting is allowed for loading purpose only.
Tender For auction sale of depot ferrous scrap - scrap ferrous melting consisting of coach cutting parts, doors,window &seat bearthnframe, eq.stay,foot step, foot rest plte, m.s. & g.i pipes & sheets, pipe fittings, fabricated structure,wire & wire rope,plane & twisted bar, shock-absorver & damper without cutting, shuckle stone, side frame key, brake shoe head,brake-beam, gear case, lower spring seat, bmbc cover,follen rod,bond strip, protective tube,tirfor,rachit, pull lift, m.s. chain, nut,bolt,washer, cutter, locking plate, expended metal, slack- adjuster, u-type bracket, clamp, trd bracket,empety electric pannel box switch board, nos-plate, wheel barrow, pandrol clip, battry box,rake blast, crusible & its parts, broken helical spring up to single coil & helical spring up to three coil, pipe &tie bar fancing, signal ladder,signal box, signal pols& other various items fit for melting released from carriage, sig, electric,trd, loco, tmc,p.way of sorts & sizes with steel,c.i., & neg. n.f. attechment if any. note :-1. loading by purchaser. 2. delivery not allowed against part payment. 3. cutting allowed for loading purpose during at the time of loading. 4. if items found other than melting at the time of cutting & loading will be seperated & not delivered to purchaser. 5. material should be delivered in sequence as per location mentioned above. location-lying at 02 (two) places at travereser- 1) line no.-11 near boundary wall. 2) near tree no. g-03 in plot- g.
Tender For supply of civil store items for rrc dwarka - ptmt bib cock with flange 15 mm dia , ptmt pillar cock , ptmt towel rail, 600 mm long , ptmt angle stop cock with flange 15 mm , unplasticised p.v.c. connection pipe with brass union 45 cm long 15 mm bore , 15 mm dia ptmt stop cock, male thread , acrylic distemper 1st quality , having voc content less than 50 grams per litrer, make,asian paint , berger,nerolac or equivalent , acrylic exterior paint, make asian paint , berger,nerolac or equivalent , synthetic enamel paint, make berger , asian paint, deluxe of akzo nobel, shalimar or equivalent , flexible coil shaped pvc waste pipe for sink and wash basin 32mm dia , anodised aluminum tower bolt barrel type 100x10 mm , anodised aluminum tower bolt barrel type 150x10 mm , anodised aluminum tower bolt barrel type 200x10 mm , anodised aluminium sliding door bolt 300x16 mm , anodised aluminium handles 125 mm with plate 175 x 32 mm , cp wall mixer 15 mm, make hindware, periware, cera or equavilant , cp basin mixer 15 mm, make hindware, periware, cera or equavilant , cp angle valve 15 mm, make hindware, periware, cera or equavilant , cp pillar cock 15 mm, make hindware, periware, cera or equavilant , cp bib cock 15 mm, make hindware, periware, cera or equavilant , cp shower make hindware, periware, cera or equavilant , cp health faucet make hindware, periware, cera or equavilant , taflon tape , solvent cement , m seal , white cement based putty, water proof , rectangular shape looking mirror, 6 mm thick , soft paint brush 4 inch width , soft paint brush 1 inch , soft paint brush 2 inch , roller paint brush , red oxide zinc chromate primer , zmb thinner , brass hanging type door stopper 150 mm , water thinnable cement primer for interior wall surface, having voc content less than 50 grams per litre , float glass panes of nominal thickness 4 mm weight not less than 10 kg per sqm , portland pozzolana cement 43 grade , coarse sand zone iii , stone aggregate 20mm nominal size , fine sand , galvanised wire mesh of average width of aperture 1.4 mm and nominal dia. of wire 0.63 mm , glass putty , water tank alarm , hydraulic door closer , ply wood 12 mm , ply wood 18 mm , msstructuralsteel, round, square or rectangular hollow tubes etc.
Tender For supply of portland pozzolana cement 43 grade , coarse sand zone iii , fine sand , stone aggregate 20mm nominal size , modular brick , reinforcement steel bar 12 mm dia , polymethyl methacrylate acrylic sheet with 3 mm thickness , cpvc pipes 20 mm dia , cpvc pipes 25 mm dia , cpvc 20 mm dia elbow 90 , cpvc 25 mm dia elbow 90 , cpvc 25 mm dia union , cpvc 20 mm dia union , cpvc 25 mm dia tank nipple , cpvc 20 mm dia tee , cpvc 20 mm dia reducer , cpvc 25 mm dia coupler , cpvc ball valve 25 mm dia , cpvc ball valve 20 mm dia , cpvc 15 mm dia tee brass , cpvc 20 mm dia female thread adapter, brass insert , cpvc 20 mm dia male thread adapter, brass insert , cpvc copper alloy float valve of nominal size 25 mm , cpvc copper alloy float valve of nominal size 15 mm , ptmt bib cock with flange 15 mm dia , ptmt pillar cock , ptmt - waste coupling 31 or 32 mm , ptmt towel rail, 600 mm long , ptmt angle stop cock with flange 15 mm , ptmt soap dish or holder 138x102x75 mm , unplasticised p.v.c. connection pipe with brass union 45 cm long 15 mm bore , 15 mm dia ptmt stop cock, male thread , acrylic distemper 1st quality , having voc content less than 50 grams per litrer, make,asian paint , berger,nerolac or equivalent , acrylic exterior paint, make asian paint , berger,nerolac or equivalent , synthetic enamel paint, make berger , asian paint, deluxe of akzo nobel, shalimar or equivalent , flexible coil shaped pvc waste pipe for sink and wash basin 32mm dia , taflon tape , solvent cement , nut bolt , ms butt hinges 100 mm size , m seal , white cement based putty, water proof , rectangular shape mirror with plastic moulded frame, 600x450 mm, 6 mm thick , soft paint brush 4 inch width , soft paint brush 1 inch , soft paint brush 2 inch , roller paint brush , red oxide zinc chromate primer , zmb thinner , ms sheet 1 mm thick , msstructuralsteel, round, square or rectangular hollow tubes etc. , glass putty , ms handle 150 mm size , ms tower bolt 200 mm size , water thinnable cement primer for interior wall surface, having voc content less than 50 grams per litre , galvanised wire mesh of average width of aperture 1.4 mm and nominal dia. of wire 0.63 mm , precoated galvanised iron profile sheets, size, shape and pitch of corrugation as approved by engineer in charge 0.50 mm //bid details 2 / 48
Tender For auction sale of condemned - atomizer (assorted)(as its condition),condemned - sticker cutting plotter machine and other items (as its condition),condemned - open metal barrel(as its condition),condemned - closed metal barrel (as its condition),condemned - damaged air baloon (as its condition),condemned - 10.00 x 20 full size flap (as its condition),condemned - 12v 25p (150 amps) plastic battery (as its condition),condemned - 12v 25p (180 amps) plastic battery (as its condition),condemned - ltv battery (as its condition),condemned - tyre buffing dust (as its condition),condemned - 10.00 x 20 radial tyre(as its condition),condemned - 11.00 x 22.50 radial tyre(as its condition),condemned - 7.50 x 16 radial tyre(as its condition),condemned - 7.50 x 16 nylon tyre(as its condition),cond - ltv tyre (assorted) (as its condition),condemned - 10.00 x 20 tube with neck (as its condition),condemned - tube cut pieces (as its condition),condemned - waste rubber materials (as its condition),condemned - waste paper records(as its condition),condemned - wooden small cut pieces, waste plywood & mica (as its condition),condemned - tree wood cut pieces(as its condition),condemned - bs iii radiator core (alu.) (as its condition),condemned - old aluminium cut pieces (as its condition),condemned - self motor (assorted)(as its condition),condemned - alternator (assorted)(as its condition),condemned - wiring horness(as its condition),condemned - electrical items :- and other items,condemned - used oil in 210 lts barrel (as its condition),condemned - used grease in barrel (as its condition),condemned - empty plastic barrel(as its condition),condemned - waste plastic materials (as its condition),condemned - auto iron (as its condition),condemned - brake drum (as its condition),condemned - broken spring leaves (as its condition),condemned - auto bearing with balls & cones (as its condition),condemned - brass bush, brass rivet (as its condition),condemned - battery cable with sleeve (as its condition),condemned - iron chips & burrs ( 12 - barrels) (as its condition),condemned - brake shoes with brake lining (assorted) (as its condition),condemned - radiator with iron frame bracket (as its condition),condemned - fuel pump assly (as its condition),condemned - power steering box with braket (as its condition),condemned - power steering box without braket (as its condition),condemned - gear box counter shaft with gear - and other items,condemned - axle shaft (assorted) (as its condition),condemned - door cylinder (assorted) (as its condition),condemned - hydraulic jack (assorted) (as its condition),condemned - machinery item lathe machine 3 nos (as its condition),condemned - waste m.s. iron scrap (as its condition),condemned - roofing iron structure & m.s.iron (as its condition),condemned - waste gi scrap (as its condition),condemned - engine oil filter and diesel oil filter (as its condition),condemned - wheel disc (as its condition),condemned - bs iii tyre lock ring (as its condition),condemned - radiator fan clutch with leaf = 830 nos (as its condition),condemned - contaminated paint tins (as its condition),condemned items : ceiling fan with leaf -and other items,condemned :- fly wheel - 168 nos, and other items,condemned - oil seperetor and other items,condemned :- radiator top tank and other items,condemned - a/c bus body shell(as its condition),condemned - bus body shell(as its condition),condemned - red bus body shell(as its condition)
Tender For auction sale of depot ferrous scrap - scrap miscellaneous m.s. cutting such as angle, channel, round bar, g.i. ducting with or without foam rubber, m.s. pipe with or without cement, gi insulator,hook ,mast multiple cantilever channel, cantilever assembly spsgi bolt,double eye distance clamp, guard box with or without wooden, air filter, plate (all type) frame, rod, ms sheet, plate, flate, tmt bar, c and w cutting, nut bolt, square bar, pin, g i rod, g i plate, box, gril, extended metal sheet, coupling, chain hook, shutter, bond strip, blower, battery box, electric box, shock absorber, all type of pipe, gi pipe, ms pipe, chain, chain pully, tikam, powrah, structure, platform structure, small rod pieces, strip, foundation, tank, sleeve, bearing plate, tensioning device, window, pannel, foot step, sheet, gear, mesh, screw coupling, stand, roller, cylinder, small auto parts, slack adjuster, hanger, link, hook, stay rod, brake shoes, coupler, adopter, cock, pick axe, beater, showel, clamp, stand, rail kaichi, rack ballast, electric pole wire support angle, fire extinguisher, rail dolly, all type of lorries with or w/o. wheels, rubber wheel tyre, tongue and other pwi tools, jali, angle frame, belly gater, coach washing machine, machine parts, rope wire, gear, various type lc & wl board of, silent block, wire basket, bucket g.i., track lifting jack, cable tray,m s chain,weigh scale, coach cutup material, empty barrels, empty drum,db grid mesh and hbac air filter etc. with or witout other ferrous and minor nf attachment old used and u.s.