Tender For supply of industrial p. l. c trainer , conveyor belt for plc , air compressor for plc , water level using float type sensor , s. c. a. d. a software simulated with plc , power transmission line trainer , over under voltage relay trainer numerical , idmt over current relay trainer numerical , power factor control relay trainer , buchholz relay trainer , ac servo motor trainer with control panel , 1 ph. ac induction motor with control panel , 3 phase ac slip ring induction motor trainer with control panel , universal motor trainer with control panel , transformer trainer kit , traic trainer , buck boost converter trainer , pwm generation using arm cortex controllers. , dual igbt module. , dual mosfet module. , 4 channel oscilloscopes with differential probe , vfd control panel with ac dissectible machine trainer , igbt three phase inverter , bldc motor with controller drive panel , permanent magnet synchronous motor with controller panel , 3 phase scim squirrel cage induction motor trainer ) /bid number: gem/2025/b/6949044 * /dated: 07-12-2025 & & / bid document1 / 26
Tender For bid to ras supply of procurement of electronic and mech components for development of working model of rg - air compressor , electric motor 3 phase ac , variable frequency drive 1 phase to 3 phase converter , magnetic pick up rpm sensor with display , arduino board with connection wires , magnetic relay , ac to dc convertor , solenoid operated 3 by 2 pneuamatic valve , pneumatic lines with adaptor connection , double acting piston pneumatic cylinder , plastic propeller , adjustable pressure reducer , small rubber tube , glue gun , limit switch , teflon tape , indication lamps , wooden table , acrylic sheet , 5v dc battery , signal cable , dc plug for arduino board
Tender For supply installation commissioning and testing of one number 11 kv neutralgroundingresistor ngr at kasnau matasukh lignite mines nagaur rajasthan
Tender For corrigendum : procurement of machineries and equipments to 90 government iti - hydraulic trainer kit with industry 4.0 set up, pneumatic trainer kit with industry 4.0 set up, oxy - acetylene gas welding complete set , d.e. pedestal grinding machine with wheels rough and smooth, drilling machine bench., pillar electric drill machine motorized., ss and sc center lathe (all geared) with minimum specification as per annexure, ev charger (home)., ev charger 3-phase, primary current injection set., thyristor /igbt controlled a.c. motor drive with vvvf control 3 phase, 2 hp, 415 v ac, dc compound motor with starter and control panel 2.5 kw ,220volts, with spring balance load.
Tender For supply of 2 w electric vehicle working model training setup in open learning format , evse test system for lab purpose , embedded development kit , trainer for studying chopper fed separately exited dc motor drive operation , trainer for studying brushless dc drive operation and control. , trainer for studying controlled rectifier fed separately excited dc motor drive operation. , ac and dc distribution trainer kit , three phase transmission line trainer kit , air circuit breaker trainer kit , linear system simulator , study of temperature control system , study of temperature transducers , dc motor torque speed study , ac motor torque speed study , setup for dc motor speed control with matlab
Tender For tender for supply of cordless small angle grinder, baʃery operated, with suitablegrinding/cuƫng wheels, 2 baʃeries 4.0 ah li-ion & 1 charger18v as per - bosch model no. gws 180-li- 100mm. make:bosch, stanley, makita or dewalt only. specificaitons: baʃeryvoltage 18v, no-load speed 11000 rpm, disk diameter 100mm, grip size front/back 185/156 , cordless portable battery operated drilling machine / drill drive model gsv 185-li of bosch; make: bosch/hitachi / metabo/ dewalt / makita , specification :- chuck size 1.5 to 13 mm , no load speed maximum 1900 rpm , battery type lithium -ion (rechargeable ), drilling capacity : steel 10 mm, battery voltage 18 volt , standard accessories : carry case, two rechargeable battery with one charger , with other other standard accessories for drilling machine / drill drive ,cordless small angle grinders, power 220-240v ac, 50/60 hz brand: bosch/hitachi / metabo/ dewalt / makita only. specificaɵons: baʃery voltage 18v, no load speed 8500 rpm, disk diameter 125 mm , co2 welding gas cylinder capacity -30 kgs confirming to is307, is-7285, is-3224, is-5844 with co2 gas refilled and isimarked self closing spindle valve having working pressuremore than 150 kg/cm2 and hydrostaɵc pressure of cylinder150-200 kg/cm2.