Tender For bid to ras supply of arduino uno microcontroller , breadboard , jumper wires male female , resistors , led red green , capacitors , transistors , diodes , sensors , lcd , relay module , motors , power supply battery , multimeter , soldering kit , project work station , fpga trainer boards , logic analyzer , dual regulated power supply , arduino uno , stm dev board , pic development kit , raspberry pi , digital multimeter , dac trainer board , rtos trainer , soldering stations , lm analog temp sensor , ds digital temp sensor , ptrtd resistance temp detector , k type thermocouple , ir proximity sensor reflective ir , digital ir obstacle sensor , ir flame sensor , ir temperature sensor mlx90614 , mq two lpg smoke , mq three alcohol , mq six lpg butane , mq seven carbon monoxide , mq air quality , pir motion sensor , ultrasonic sensor , accelerometer , gyroscope , solderless breadboard full size , mini breadboard , jumper wires male male , jumper wires male female , jumper wires female female , ic socket eight pin , ic socket fourteen pin , ic socket sixteen pin , solar cell trainer kit , ujt as relaxation oscillator kit , scr characteristics kit , ldr , photo diode , phototransistor , semiconductor temperature coefficient trainer kit , logic gate trainer kit , ic trainer kit , measurement of steady state and transient response of rl rc and rlc circuits , frequency response of twin t notch filter and to study of active filter , study of single phase inverter trainer , to study the behaviour , determine the transient , to study of pid controller for simullatio n process , to study basic electric al trainer , to study single phase transformer , to obtain efficiency of a dc shunt machine , to obtain efficiency and voltage regulation of a single phase transform , to study dc series motor , make connection of dol starter , test the machines required , maxwells bridge trainer kit ) /bid number : gem/2026/b/7582907 * /dated: 27-05-2026 & & / bid document 1 / 44
Tender For corrigendum : rate contract for medicine - stainless steel abdominal hysterectomy set, n.s.v set (s.s), g.v set, self abdominal detractor, m.t.p set., vaccine carrier (small size), x-ray digitalisation with high-end cr system (with installation & 1 yers. warrenty) console software with mulitmodality work station the cr system should have advances workstation provided with 17" high resolution monitor, keyboard & ouse, with the fol., digital ultrasound machine colour dopler (high resolution ) with 4 probe, semi auto analyzer, fully automated bio-chemistry analyzertechnical specificationsthroughput-150t/hr (constant with both mono and double reagent)system function-random access/stat/batchtest method-end point, fix time, kinetic, (single/double reagents chemistry, mono/ bio-chromatic measurements)calculation methods-1 point linear, 2 point linear, exponential, logit log3p, logit log 4 p, logit log 5p, spline, line graph, k factorblank-reagent blank, sample blank, pre sample blank, pre reagent blanksample tray-40 position, sample volume :2-30 ui, 0.1 ul increment, micro cup, & test tube can be used for samplereagent tray-80 position, reagent volume: 20-300 ul, 1 ul incrementmixing system-teflon coated mixersample probe-1 needle with liquid detector, shock sensoroptics-halogen-tungsten lamp, absorbance range: 0-4.0 abs resolution: 0.0001 abs.diffraction photometry with wave length: 340, 405, 450, 505, 546, 578, 630, 700nm & 4 more optionswash station-12 step washing, 4 needle wash station, 1 dry pad, external needle cleaningcalibration-linear and non-linearqc-multi-level qc setup with levy-jennings graph and westgrads multi rules with mean sd, and cvwater consumption-not more than 6l/hrtemperature-reagent: 2-14 c (24 hr refrigeration), reaction cuvette: 37c 0.1 humidity- 80%system interface-usbpower requirement-ac 220v 10%, 50/60 hzdimensions-750 mm*560mm*530mm, hotair oven, binocular microscope (olampus), centri fuge machin (good quality), micropipette (0-50 microliter), micropipette (0-500 microliter), micropipette (0-1000 microliter), microtips (0-50 microliter), microtips (0-1000 microliter), bed side screen with cloth 1"round pipe with wheel, sponge holding (all size), artery forceps 6" curved, artery forceps 6" straight., artery forceps 8" curved, artery forceps 8" straight., artery forceps 4" straight., alliys tissue forcep (all size curved straight), mosquito forcep (all size curved straight), scissor 6 " curved (all size), scissor 6 " straight (all size), scissor mosquito straight. (all size curved, straight), diatheromy (machine), laparoscopic instrument full set (best quality), needle holder 8 "curved, needle holder 8 " straight, needle holder 6 "curved, needle holder 6 " straight, needle holder 4 "curved, needle holder 4 " straight, doner couch (3 motor), blood weighting mechine, blood band refrigerator (300 bag) temp.display outside, elisa reader with washer mechine with printer & ups., doner couch (3 motor), blood weighting mechine, blood band refrigerator (300 bag) temp.display outside ( best quality), fully automated chemiluminescence analyzer(clia) 1. system should be fully automated walk -away with continuous loading facility.2. analyzer should have able to perform thyroid, bone, cardiac, fertility, diabetes and anemia profile test.3. working principle of system should be micron super paramagnetic particles platform with alp labeled reagents and amppd substrate.4. must have 3 phase magnetic separation with precisely controlled temperature.5. analyzer should have photon counting detection mode with photomultiplier photo counter with led reference module.6. the analyzer must have vortex non-touch mixing which can reduce carryover., 7. throughput of the system should be more than 180 tests in a hour.8. system should have 15 reagents onboard with onboard 2 -8 nonstop refrigeration facility 9. system should have at least 50 sample positions and continuous loading facility.10. system should have cont
Tender For supply of set up to find the coefficient of thermal conductivity of a good conductor (copper) using searl's me , setup to find numerical aperture of an optical fibre , set up to use a prism shaped double refracting crystal to determine the refractive indices of the qu , set up to measure birefringence of mica , set up to determine the cofficient of viscosity using capilary flow method , sextant , set up to measure of planck s constant using black body radiation and photo-detector , set up to find the coefficient of thermal conductivity of copper (cu) by angstrom method , set up to calibrate a thermocouple to measure temperature in a specified range by direct method and/ , set up to study the variation of thermo e. m. f. of thermocouple with difference of temperature of its , setup to determine the temperature coefficient of resistance using platinum resistance thermometer ( , setup to determine the temperature coefficient of resistance by platinum resistance thermometer (prt , set up to determine coefficient of themal conductivity of a bad conductor by lee and charlton's disc , set up to study the pe hysteresis loop of a ferroelectric crystal probes arrangement , set up to measure the dielectric constant of a dielectric materials with frequency , set up for the measurement of field strength b and its variation in a solenoid (determine db/dx) , set up to study magnetic field variation along the axis of a circular coil and in a helmholtz coil