Latest oil pump repair Tenders | Government oil pump repair Tenders

State Government

CTN :45596388

23 Jun, 2026 NA

Delhi - Delhi

Tender For supply, installation, testing and commissioning of electrical and mechanical equipments for shallow bore tube wells phatak bans,sawar khan, chatta mom gran, lal darwaza in matia mahal constituency ac-21. - s/o submersible pump set fitted with dynamically balanced ep impeller mounted on stainless steel shaft protection sleeve ep stage bowl of closed grained shorted type impeller. the pump will be directly coupled to required wet type induction motor of speed 2900 rpm suitable for operation on three phase ac, 415 volts ,50hz, 5 hp, model no j46, head-70 mtrs, discharge-200 lpm. make:bs/ksb/crompton/djb approved, supply of automatic lt panel board suitable for 415 volts, 3 phase, 50 hz, 4 wire system for operation of up to 15 hp submersible set, made out of not less than 2 mm thick crca for load bearing members and 1.6 mm for doors of panel, totally enclosed, dust and vermin proof, floor mounted type. the panel size 760 mmx 1360 mm x300 mm and having (1) 63 amp change over- 1 no (2) 63 a tpn mccb -1 no (3) amp meter 0-50 a- 1 no (4) voltmeter 1 no (5) amp & volt meter selector switches-1 set (6) auto-manual + light + control mcb tp 32 amp- 1nos each (7) ct -3nos (8) push button + on/off light 2 nos each (9) 5 kvar shunt capacitor- 1 no (10) aluminium bus bar size 25 mm x 6 mm - 1set (11) 15 hp star delta starter (a) 32 amp power contactor-3 nos (b) overload relay 14-23 a -1 no (c) star delta timer- 1 no ( d) qt timer -24 hours -1 no (e) motor protection relay 200 short circuit, earth fault, phase loss, unbalance, phase reversal, locked rotor protection make:-subtec/protech/ l&t/all djb approved make, s/o pvc insulated flat submersible cable with copper conductor having three core size 2.5 sq mm 1100 volts(100mtr per roll). make- gloster/universal/havells/grandlay/djb approved, s/o g.i pipe 40mm dia medium class with threaded externally on both end socketed 6mtr long. make- jindal/tata., s/o g.i tail piece 40mm dia 600mm long medium class with threaded externally on both end. make- tata/jindal, s/o gi socket 40 mm dia with threaded internally. make: jindal/tata/djb approved, s/o gi elbow with both end having thread, size- 40mm. make: jindal/tata/djb approved, s/o gi reducer having thread on boyh end, size: 50mm to 40mm. make: jindal/tata/djb approved, s/o gi union having thread on both end, size: 40mm. make: jindal/tata/djb approved, s/o ms clamp of 600mm long 12mm thick complete with nut & bolts and washers for holding 40 mm dia pipe i/c bending & shaping etc., supply of ms bore cover 6 mm thick suitable for 100 mm dia casing in 2 pieces complete with bolting arrangement angle iron frame and provision of 40 mm dia hole in the center., supply of pvc suction hose pipe 50 mm dia 30 mtr long.make-jyoti/isi, installation of submersible pump set with pipe and other accessories, connection of cable, installation of electric panel, grouting of electric panel digging and fixing the same with the help of cc and laying of gi pipe from bore to panel executing minor civil making electrical connection with cable as required size i/c watch and ward cartage, taking all safety measures all tools and tackles. testing and commissioning of all e&m equipment on no load and full load conditions as per standard and full satisfaction of engineer-in- charge. this is a turnkey job and it further includes any left out items which may be required during execution of work will be firm responsibility & no extra payment will be paid. - s/o submersible pump set fitted with dynamically balanced ep impeller mounted on stainless steel shaft protection sleeve ep stage bowl of closed grained shorted type impeller. the pump will be directly coupled to required wet type induction motor of speed 2900 rpm suitable for operation on three phase ac, 415 volts ,50hz, 5 hp, model no j46, head-70 mtrs, discharge-200 lpm. make:bs/ksb/crompton/djb approved, supply of automatic lt panel board suitable for 415 volts, 3 phase, 50 hz, 4 wire system for opera

CTN :45443500

25 Jun, 2026 69

Anekal - Karnataka

Tender For corrigendum : procurement of pump motors and allied accessories for hennagara gram panchayat for the financial year 2026-27 - motor and pump 12.5hp 25 stage, motor and pump 5hp 50 stage , motor and pump7.5hp 56 stage, motor and pump 15hp 30 stage , motor and pump 20hp 40 stage, motor and pump 17.5 hp 36stage, motor and pump10hp 20 stage, motor and pump 25hp 40 stage pump, submersible cabel 4sq 3 core , submersible cabel 6sq 3 core , submersible cabel 10sq 3 core , starter 5hp - meco, starter 7.5hp - meco, starter 15hp - meco, starter 17.5hp - meco, starter 20hp - meco, panel board - iso certified, alluminium wires 6sq.mm - iso certified, alluminium wires 10sq.mm - iso certified, alluminium wires 12sq.mm - iso certified, alluminium wires 16sq.mm - iso certified, alluminium wires 20sq.mm - iso certified, gi pipe 2 inches class b , complete panel board items, gi clamp set bore cap, gi collar 2 inch - iso certified, sealent 100ml - iso certified, axcel blades- iso certified, gi bend 2 inch- iso certified, gi nipple feet 2 inch- iso certified, gi nipple 0.75 1feet - iso certified, gi nipple 0.75 2feet - iso certified, gi collar 0.75 inch- iso certified, gi elbow 0.75inch- iso certified, gi nipple feet 1 feet 0.5 inch- iso certified, gi nipple feet 2 feet 0.5 inch- iso certified, gi collar 0.5 inch- iso certified, gi elbow 0.5 inch- iso certified, gi 2 nrv- iso certified, solvent cement gum- iso certified, brass gate wall 2 inches- iso certified, brass gate wall 2.5 inches- iso certified, gi gate wall 2 inches- iso certified, gi gate wall 2.5 inches- iso certified, gi tap 0.5 inches- iso certified, gi tap 0.75 inches- iso certified, gi union 2 inches- iso certified, gi union 2.5 inches- iso certified, gi union 2 inches- iso certified, gi union 3 inches- iso certified, gi tee 0.5 inches- iso certified, gi tee 0.75 inches- iso certified, gi elbow 0.5 inches- iso certified, gi elbow 0.75 inches- iso certified, gi coller 0.75 inches- iso certified, gi coller 2 inches- iso certified, gi pipe 0.75 inches with thread- iso certified, gi thread end cap 0.5 inches- iso certified, hdpe pipe 1.5 inch 20 gauge - iso certified, hdpe pipe 1.25 inch 20 gauge- iso certified, end connection for hdpe- iso certified, motor for open well 1 hp, pump and motore 10hp 50 stage, pump motor 20hp 50 stage, motor 5hp 10stage pump, motor and pump 7.5hp 15stage, amphere meter, volatage meter, pump and motor 25hp 50satage

CTN :45592297

24 Jun, 2026 30.00 Lacs

Pahalgam - Jammu And Kashmir

Tender For supply installation testing and commissioning of pump unit and other electro-mechanical equipments at laripora pahalgam - supply, installation, testing and commissioning of submersible type pump sets with motors and allied mechanical and electrical components/ items as per manufacturer s recommendations and guide lines, and as per the scope of the work at site. the equipment supplied conform to latest is- standards and codes with fail safe circuits/ devices for(i) over loading (ii) under loading (iii) clogging (iv) shut off (v) low liquid level (vi) single phase prevention devices (vii) over heating etc. the pumping units shall have following technical specifications: pumps:type of pump :non clog centrifugal volute type sewage submersiblepumpscapacity= 28.4lpshead = 17.5 metres or abovesolid handling capacity: 20mm (minimum) quality of water: sewage water to be handled meterial of construction:pump casing : cast ironimpeller : stainless steelpump shaft : stainless steelmotor body : cast ironsealing : dual mech. seal...contd.. as per annexure-a, providing/supplying and fitting of 100 mm m.s flanged delivery main to be connected with existing rising main at site. the job includes providing and welding of m.s flanges 12 mm thickness. the flanges shall be double welded both from inside and outside of the pipe using standard electrode of reputed make. the cost on account of supply/ fabrication of bends and providing/ fitting of flanges is included in the job. (complete job)., providing and fitting of 100 mm dia ductile iron double flanged, non-rising spindle soft seated glandless gate/ sluice valves as per is14846 for regulating the water supply outside the pumping units p.n rating 1.0.the job includes providing and fitting of 02 nos. m.s flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with rising main of the pumping unit at appropriate spots as per site requirement (complete job)., providing and fitting of 100 mm dia ductile iron double flanged, slanted seat swing check valve( nrv) as per is 5312 p.n rating 1.0.the job includes providing and fitting of 02 nos. m.s flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with rising main of the pumping unit at appropriate spots as per site requirement (complete job)., gantry over sump :- fabrication, providing, fitting of ms gantry over sump with 02 nos. vertical columns. the gantry fabricated out of ismb-100, 3.25 mts long placed face to face. 300x300mm ms plates 12mm thick fitted on top and bottom side of column .bottom plate welded to the reinforcement of the sump and grouted in 1mx1mx1m pcc 1:1.5:3 mix. ismb-100,3mts long is to be placed and welded to the top plate of the columns .the job also includes providing and fitting of 2-tonne capacity chain pulley block with monorail along with hoisting chain (complete job)., providing and fitting of 50 mm23.5 core ,al pvc insulated cable, armouredfor internal connectionscrimping, taping etc. note:- the cable terminal ends for connection to switchgear at various requisite points shall be al. thimbles and of appropriate size and connected by hydraulic crimp tool only (complete job)., providing and fitting of 4-core 16 mm2 flat /circular submersible copper cable conforming to is: 694 (part 1st) 1964 & is: 694 (part 2nd) - 1964 for submersible pumping unit and other electrical equipment s. the cable connections terminal shall be fitted with copper thimbles of required size (complete job)., fabrication, providing and fitting of main electric control panel of appropriate size fabricated out of 14 swg sheet having required openings/vents and protection class : ip-55 & fitted with accessories as under: a) bus bar chamber: 160 amperes(tpn) b) main circuit breaker (incomer mccb) qty:- = 01 nocurrent rating = 160 amp. c) change over switch:qty. = 01 no.rating = 160 ampere....contd... as per annexure-a., electrification. providing/fitting of lighting and fan points (06) in

CTN :45585777

22 Jun, 2026 NA

Una-Hp - Himachal Pradesh

Tender For energization of hand pump under lwss aloh near yusuf khan & handpump of bagda ward no-5 & handpump of chower ward no-2 in tehsil amb distt una (hp) sh:- 1 (s/ei no submersible pump set with allied accessories near house of yusuf khan) 2 handpump of complete panel board)

CTN :45415159

19 Jun, 2026 4.58 Lacs

Chandigarh - Chandigarh

Tender For corrigendum : repair and maintenance of tube wells and boosters including repair of water level gauge, ms panel, sluice valves and allied items of civil / electrical at various buildings i.e. punjab raj bhawan, haryana raj bhawan & residence sector-7, under maintennace booth, sector-7, chandigarh. (ch to: 2216 (np) mtc. and repair ) - repair of ci sluice valve up to 150 mm dia including dismantling, repair / replacement of spindle, nut , rubber packing, nuts and bolts complete., up to 100 mm dia, lifting and lowering of submersible pump set including dismantling of flenged joints, taking out column pipes, re-jointing etc including replacement of defective packing, nuts and bolts etc complete, tube well, booster, supplying and fixing of single phase preventor make minilec or equivalent model of approved make to the satisfaction of eic , supplying and fixing of current transformer ( ct ) for ampere meter of suitable rating complete., supplying and fixing of overload relay of following capacities, 14 to 23 amp, 30 to 42 amp, 45 to 75 amp, providing and fixing of star delta starter timer of make l&t or equivalent model of approved make to the satisfaction of eic, providing and fixing of kit kat 500 amp complete in all respect, supplying and fixing of capacitor of 20 to 50 mfd make l&t, siemens or equivalent model of approved make to the satisfaction of eic , supplying and fixing of analog meter of make l&t ( rishabh ) or equivalent model of approved make to the satisfaction of eic , volt meter, ampere meter, supplying and fixing of 3 pole mccb of following capacity of make l&t, bch, havells or equivalent model of approved make to the satisfaction of eic , 100 amp, supplying & fixing of contactors block of make l&t, bch or equivalent model of approved make to the satisfaction of eic , mnx - 25, mnx - 32, mnx - 50, mnx - 70, supplying and lowering of submersible cable 16mm2 of make havells, finolex, l&t or equivalent model of approved make to the satisfaction of eic , supplying and lowering of submersible cable 25mm2 of make havells, finolex, l&t or equivalent model of approved make to the satisfaction of eic , providing and fixing hydro pneumatic pump of size 0.5 hp of approved make with 24 ltr capacity tank, pressure switch, pressure gauge, nrv accessories and making connections complete of make crompton or equivalent model of approved make to the satisfaction of eic, repair and rewinding of submersible pump set including carriage from installation to workshop and back. the rate include replacement of all defective parts of pump and motor rewinding., 5 hp, 7.5 to 10 hp, 35 hp to 55 hp, repair and rewinding of monoblock submersible pumping set including repacement of defective parts as required and carriage from installation to workshop and back., 0.5 h.p, 1 h.p, 2 h.p, manufacturing, supplying and fixing of ms control panel 16 gauge of size 600x700mm with door including wiring of inside panel, complete in all respect, providing and fixing of self pumping monoblock single phase pump for boosting of make crompton or equivalent model of approved make to the satisfaction of eic, 0.5 h.p, 1 h.p, 2 h.p, providing and fixing of pressure gauge make h-guru or equivalent model of approved make to the satisfaction of eic, providing and fixing of elcb 63 amp make l&t/havells or equivalent model of approved make to the satisfaction of eic, repair of internal control wiring 1.5mm wire with thimbles, nut bolt etc. complete

CTN :45577934

24 Jun, 2026 NA

Ghaziabad - Uttar Pradesh

Tender For providing of repair and overhauling service - repair of royal ati and oil pump; repair of royal ati and oil pump; yes; buyer premises

Central Government And Public Sector

CTN :45346149

24 Jun, 2026 NA

East Champaran - Bihar

Tender For corrigendum : supply of kirloskar make pumps spares on door delivery basis at hbl plant sugauli, east champaran, bihar - supply of kirloskar make pumps spares at hbl plant sugauli as per the technical specification mentioned below:, bare pump model db 100/40 or ib 100/40xe,ci impeller, wearing plate de sp-4l make kirloskar, screw counter sunk m12 1.75 50 mm lft ss make kirloskar, nut hex head (ms) sp-4l m12 1.75, sewage dewatering submersible pumpmodel eterna 15000cw 4plpower rating 15 kw / 20 hpdelivery size 150 mmrated voltage 380 vspeed 1440 rpmmax solid handling size 45 mmhead range 6 m to 20 mflow 288 m /hr to 400 m /hrimpeller cidelivery casing cimotor body cipump shaft cspump make kirloskarsuitable cable for eterna 15000cw 4pl pump 30 m with star delta panel., self-priming pump coupled with ie2 motor, starter, and cablemodel sp4l + with 12.5c4 motor power rating 9.3 kw / 12.5 hpsuction 100 mmdelivery 100 mmrated voltage 415 vspeed 1450 rpmimpeller dia 292 mmhead range 10 m to 26 mflow range 41 lps to 16 lpsmaterial of construction (moc):impeller cidelivery casing cimotor body cishaft c40sealing gland packingpump make kirloskarstar delta panel for sp4l pumpsuitable cable for sp4l pump 30 m.

Central Government/Public Sector

CTN :45590449

29 Jun, 2026 NA

Cuddalore - Tamil Nadu

Tender For horizontal submersible open well pump with motor suitable for clear water application having discharge range of 2.15lps to 3.75 lps against head range of 20 meters to 14 meters respectively, with delivery size of 25 to 40 mm and pump efficiency not less than 55% at duty point of 16 meter head, suitable for operation on 230 v ac, single phase, 50 hz supply system, supplied with standard accessories such as flat cable, capacitor and starter panel etc., conforming to is 8034, is 9283 and relevant applicable indian standards with isi marking. accepted makes: kirloskar, ksb, deccan, texmo. similar to kirloskar make model kosi-123, ksb make model opal 10cx i or mr(s) 10x. offers shall be accepted only from manufacturers or their authorized dealers, along with proof of purchase from the oem at the time of material supply. [ warranty period: 12 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45540427

04 Jul, 2026 20.00 Lacs

Ramgarh - Jharkhand

Tender For repair/maint of centrifugal pump sets, submersible pump set, panel starters, flocculator and chemical dosing system and connected items under ge ramgarh cantt

State Government

CTN :45562686

22 Jun, 2026 6.58 Lacs

Ambala - Haryana

Tender For repair of submersible/horizontal pumping sets for tubewells only consisting mainly of motor pump, electrical control panel, starter cable and all accessories sluice valve, non return valve specials etc. including all appurtenances at existing 56 nos.

Oil Pump Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government And Public Sector

Central Government/Public Sector

Central Government/Public Sector

State Government