Latest oil spill response services Tenders | Government oil spill response services Tenders

State Government

CTN :40227801

27 May, 2025 49.58 Lacs

Gandhinagar - Gujarat

Tender For various routine/preventive and breakdown maintenance work on as and when require basis at chp-gtps - replacement of hammer rings for stage ii crusher , replacement of hammer rings for stage i crusher , replacement of screen plate / breaker plate/kick off plate of stage i and ii crushers , replacement of rotor of stage i crusher with disassembling of removed rotor and assembling of new/repaired rotor , replacement of drive end side bearing / pedestal of crusher rotor or complete gear coupling set of crusher or repositioning of dislocated rotor of crusher , replacement of non drive end side bearing/pedestal of crusher rotor or complete alignment of crusher motor with crusher rotor , replacement of broken hammer rings of stage i and ii crushers (stage i crusher up to 12 nos.of hammer rings and stage ii crusher up to 06 nos. of hammer rings at a time) , replacement of rail of rail table of wagon tipplers 1/2/3/4 (in one side full length) , replacement of clamping rubber pads of clamp for wagon of wagon tipplers , replacement of whole resting pads for wagon of side beam of wagon tipplers , replacement of spill plate roller of wagon tipplers , repairing/preparation/ fitting and replacement of hooks/rods/turn buckle, chain, sling rope ,spring assembly etc. of vibrating trays and crusher house trays , spillage control at various locations , miscellaneous cutting/welding work require at various locations , replacement of gearbox in conveyor no. 2a/b,11a/b,12a/b,13,14/15,16a/b,17a/b ,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of gearbox in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement of slow speed coupling set (two halves) of drive pulley , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.2a/b,11a/b,12a/b,13,14/15,16a/b,17 a/b,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement/removing/refitting of various size and type of fluid coupling , replacement or removing & refitting of any internal/bearing/input/ output oil seal of various size and type of gear box , overhauling of dismantles old/used gearbox in all respect with fitment of input and output coupling. , replacement of drive pulley , replacement of drive end side bearing of drive pulley or repositioning of dislocated drive pulley , replacement of non drive end side bearing/any side pedestal of conveyor drive/non drive pulley , alignment of motor/ gearbox/drive pulley including decouple/couple of coupling , nut bolt and drive system checking with replacement of broken nut bolt in all 04 wagon tipplers no.1/2/3/4 as per scope , lifting and releasing of gravity take up of any conveyor belt for locking and de locking of belts for other than belt replacement work , loosening and tightening of horizontal type screw take assembly of any conveyor belts for other than belt replacement work , work of dismantling and re erection of new/repaired apron pan from existing apron feeder of wagon tippler , repairing of upper/lower structure/cone plates of damaged/bend apron pan , replacement of carrying roller of apron feeder , replacement of worn out/ damaged ti roller and garland rollers. , replacement of worn out/ damaged impact rollers , replacement of worn out/ damaged return rollers , replacement of various worn out/ damaged ti roller stands , replacement of various worn out/ damaged impact roller stands , replacements of various worn out/ damaged return roller stands , replacement of various worn out skirt rubbers [10 m each] and skirt rubber with angle , preparation and replacement of guide rollers with bracket in place of worn out/ damaged guide rollers as

State Government

CTN :40240431

10 May, 2025 NA

Nagpur - Maharashtra

Tender For work contract for lifting, shifting and overhauling of 575 / 800 kw crusher motor on as & when required basis in chp-i.

State Government

CTN :40226612

07 May, 2025 NA

Khaperkheda - Maharashtra

Tender For work of lifting / loading / transportation and unloading of spilled coal from chp-ii premises to required locations in tps khaperkheda premises on as and when required basis

Central Government And Public Sector

CTN :40241179

27 May, 2025 1.26 Crore

Faridabad - Haryana

Tender For providing of facility management services - lumpsum based - commercial; housekeeping, work of housekeeping sweeping cleaning dusting lifting & disposal of garbage filling of water containers etc in different offices telephone exchange premises of faridabad ba zo..

Central Government And Public Sector

CTN :40241125

27 May, 2025 1.62 Crore

Gurgaon - Haryana

Tender For providing of facility management services - lumpsum based - commercial; housekeeping, work of housekeeping sweeping cleaning dusting lifting & disposal of garbage filling of water containers etc in different offices telephone exchange premises of gurgaon ba zone..

CTN :40245812

04 Jun, 2025 NA

Kharagpur - West Bengal

Tender For electrical work for replacement of power supply equipment with rdso approved ips at lc nos. ph-18, ph-23, ph-46, ph-55, ph-59, td-10 & td-35; overaged 9 nos. electric lifting barrier and different parts of elb in kharagpur division.

CTN :40218970

12 May, 2025 88

Yelahanka - Karnataka

Tender For pump motor repair - guide vane, oil seal steel bush(oil seal sleeve), oil seal(pump oil seal), intermediate piece (i.p.) with i.p. leaded bronze bush, pump bowls, rewinding of motor of 20 hp, rewinding of motor of 17.5 hp, rewinding of motor of 15 hp, rewinding of motor of 12.5 hp, rewinding of motor of 10 hp, rewinding of motor of 7.5 hp, rewinding of motor of 5 hp, rewinding of motor upto 3 hp, transportation of pumping machinaries, motor base with pin, circlips(small), bearing (gun metal bush) centrifugal cost aluminium bronze bearing bush, studs and nuts, tip carbon/ferrode padding, thrust bearing block assembly (tb bottom), carbon housing(tb plate), lock ring(circlip big), lower housing, upper housing, lower flange, upper flange, labour charges (overhauling of pump only), brass filter, strainer, cable guard, pump coupling (stainless), pump key (stainless steel) upto 8 stages, pump shaft (stainless steel) counter less ground with key way upto 8 stages, allen screw, steel bush (i.d.o. ss sleeve), d.o. bearing( i.d.o lb bush), discharge outlet (d.o.) bearing(lb bush) and d.o steel bush(ss sleeve), impeller shell moulded with aluminium & bronze, supply and fixing of voltmeter, supply and fixing of ammeter, supply and fixing of led indicator, supply and fixing of wiring kit(sd upto 25hp), supply and fixing of wiring kit(dol upto 7.5hp)(mr), supply and fixing of no-volt (nv) coil, supply and fixing of terminal plate (connector 60a), supply and fixing of terminal plate (connector 30a)(mr), supply and fixing of ryb rotary switch(volt selector), supply and fixing of single phase preventer(20 to 30 hp), supply and fixing of single phase preventer(7.5 to 15 hp) (mr), supply and fixing of 15 amps relay (mr), supply and fixing of 23 amps relay (mr), supply and fixing of 33 amps relay, supply and fixing of 25 amps contactor, supply and fixing of 16 amps contactor(mr), erection of panel board & ms box (outdoor type) (gulbarga pred, pg.no.57, lt.no.12.2), supplying and fixing angle iron frame work fabricated out of m.s. angle iron and m.s. flat with bolt, washer etc and painted with 2 coats of red oxide and then two coats of approved paint 75x75x6mm (pwd ele sr 2014-15, pg.no.49, lt.no.6.39.3), refilling available earth around pipe lines, cable in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specification pre sr 2011-12, p-3,1-6., labour charges for laying u.g. cable upto 3.5 core 25 sq.mm as per pwd electrical sr 2010-11, p-68,1-1, class a pvc cable, lifting of struck up submersible pump set above 300 ft (bwssb sr 2017-18/o150g/sl no.27), lifting of struck up submersible pump set upto 300 ft (bwssb sr 2017-18/o150g/sl no.26), labour charges overhauling, lifting of submersible pumpsets, re-errection charges of pumping machinery including overhauling and painting, cable joint, g.l. pipe threading including transportation, labour charges (for over hauling), supply and fixing of ct coil 50/5 & 75/5, supply and fixing of blade set 25a, supply and fixing of blade set 16a(mr), supply and fixing of hylum brand hand plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc and fixing of exciting wood or metal box using nf screw , supplying and fixing polished wood board made out of not less than 15mm thick planks at both sides with planks made out of not more than 2 pieces and fixing the same to the wall using tapered wooden plugs screws etc, fabricating, supplying and mounting ms box made out 14 swg suitable for foor/wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front over equipped with temper proof locking arrangements with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enamelled metal paint etc., com

Central Government And Public Sector

CTN :40217386

24 May, 2025 69.07 Lacs

Ambala - Haryana

Tender For providing of facility management services - lumpsum based - commercial; housekeeping, work of housekeeping sweeping cleaning dusting lifting & disposal of garbage filling of water containers etc in different offices telephone exchange premises of ambala ba zone ..

Central Government And Public Sector

CTN :40217474

24 May, 2025 78.02 Lacs

Ambala - Haryana

Tender For providing of facility management services - lumpsum based - commercial; housekeeping, work of housekeeping sweeping cleaning dusting lifting & disposal of garbage filling of water containers etc in different offices telephone exchange premises of ambala ba zone ..

CTN :40218938

12 May, 2025 6.54 Lacs

Pandavapura - Karnataka

Tender For sunkathonnuru uppina katte de-shiltting work - pg_water, pg_gravel 2.36 mm/murrum, pg_laboratory asst. (sslc passed)/mate/supervisor, pg_wheeled dozer (d50 beml), pg_motor grader 3.35 meter blade, pg_water tanker, pg_vibratory roller 8 tonne, pg_transportation/loading and unloading of material/lifting of material /wastage/unforeseen charges/miscellaneous which are necessary during execution., pg_boulders, pg_spall (jelly used for packing), pg_broken stone aggregate 40 mm size, pg_broken stone aggregate 20 mm size, pg_broken stone aggregate 12 mm to 10 mm size, pg_coarse sand (zone iii), pg_portland cement, pg_mixer (concrete) - 1 cum capacity, pg_add watering charges at 1 % on material, pg_add sundries charges at 1 % on material, pg_size stone 20 x 20 x 25 cms, pg_bond stone 20 x 20 x 45 cm, pg_mixer (concrete small used in culvert), pg_mason class i (with tools), pg_mason class ii (with tools), pg_stone chistler class ii, pg_casurina poles 100 - 150 mm, pg_add handling , loading and unloading at 1% on material, pg_add sundries charges at 2 % on material, pg_jungle wood runners and planks, pg_silver oak or equivalent planks 38 mm thick, pg_add handling , loading and unloading at 2% on material, pg_tractor - 40 hp, pg_crushed stone course aggregate 53, pg_granite metal 40 mm, pg_granite metal 20 mm, pg_crushed stone chippings 13.2 mm, pg_gst

Oil Spill Response Services Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

Central Government And Public Sector

Central Government And Public Sector

Central Government And Public Sector

Central Government And Public Sector