Latest opc drum Tenders | Government opc drum Tenders

CTN :45704802

06 Jul, 2026 NA

Jhansi - Uttar Pradesh

Tender For supply of dvd writer , ssd 256gb , fuser unit , opc drum , ram 8gb , main board

CTN :45714403

30 Jun, 2026 NA

Leh - Jammu And Kashmir

Tender For supply of opc drum (q3)

CTN :45714938

13 Jul, 2026 1.40 Lacs

Rampur-Up - Uttar Pradesh

Tender For tender for supply of repairing overhauling , calibration recommising of multichannel temperature indications , rewiring commissining of digital display system , repairing , calibration & commissining of high/low alarm system on boilers , repairing calibration commissining of steam measurement system , repairing rewiring calibration of super heated steam temp monitoring , reparing calibration of differential pressure transmitter , reparing calibration of flow indicator cum totalizer , repairing calibration commissining of steam measurement system , repairing calibration of old pid controller , amc of various wiring commissioning of temp monitoring point , air filter , onoff control valve , wheel valve , brass adapter , onoff digital controller , solonoid valve , temp compensating cable , temp sensors , needle valve size , installation commissioning , air filter , onoff pneumatic control valve , wheel valve , instrument cable , pid controller level indicator , solonoid valve , temperature gauge , high pressure pipe , oil pocket thermowells , digital temp indicator , pressure gauge , pressure gauge , pressure gauge , vacuum gauge , temperature gauge , socket

CTN :45694953

27 Jul, 2026 NA

Multi City - Multi State

Tender For bench top pressure gauge calibrator with accessories- pressure calibration system, maximum no. of pressure module simultaneously, working medium, mode, sensor module range 1, accuracy of sensor module range 1, sensor module range 2, accuracy of sensor module range 2, precision, uncertainty of sensor module range 1, uncertainty of sensor module range 2, measurement modules, control mode, control precision, lowest controllable pressure limit, pressure indication & display system, over pressure protection, leak test & switch test, jog wheel, system mode, valve driver, vacuum pump, contamination prevention system, pressure display units, dc voltage range, dcv resolution, dcv uncertainty, dc current range, dci resolution, dci uncertainty, loop compliance voltage, hart mode, automatic hart detection, hart selectable resistor, write protection, hart commands, remote communication interface hardware, ac power supply, operating temperature range, relative humidity, ingress protection, plumbing lines, fittings and adaptors, warranty, calibration certificatte, test port max. pressure limit, reference port max. pressure limit, vent port max. pressure limit, test port, supply port max pressure limit, liquid or particle filter

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

CTN :45695018

16 Jul, 2026 NA

Dehradun - Uttarakhand

Tender For opc drum for kip wide format led printer

CTN :45688750

06 Jul, 2026 NA

Delhi - Delhi

Tender For tactile grip pressure measurement system

CTN :45697869

06 Jul, 2026 25.0 Thousand

Delhi - Delhi

Tender For supply of pressure roller , logic card , gear set , main motor , teflon sleeve , opc drum

CTN :45689357

06 Jul, 2026 NA

Ahmednagar - Maharashtra

Tender For supply of ssd 4 tb sata , paper cassette tray sharp , opc drum sharp bp 20m 22t , cleaning blade bp 20m 22t , printer head l4260 , printer head 3250 , motherboard m510

CTN :45649462

02 Jul, 2026 56.9 Thousand

Bhopal - Madhya Pradesh

Tender For supply of maintenance box canon , opc drum kyocera , developer , maintenance box epson , controller card 3kva online ups , keyboard and mouse wired , ram laptop , fuser assy photocopier , graphics card 4gb

Opc Drum Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors