Latest outside caliper Tenders | Government outside caliper Tenders

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

Central Government And Public Sector

CTN :45616428

25 Jun, 2026 NA

Lumding - Assam

Tender For supply of export quality pwi tool kit model tk-1 for rgm machine consisting of following items- 1.clearance gauge bg 2. shim feeler gauge.3. stepped feeler gauge 4. tapered gauge. 5. gap gauge. 6. rail thermometer similar to model mfmbt-a. 7. pair of versine holder. 8. versine scale. 9. nylon cord on winder. 10. magnifying glass.11. adjustable mirror for checking cracks. 12. vertical wear measuring gauge similar to model vwg-1. 13. vernier caliper. 14. track square. 15. rail profile plotting curve. 16. steel scale 12inch /300 mm. 17. outside caliper 150 mm.18. inside caliper 150 mm. 19. spirit level similar to model sl-2. 20. white clad pocket steel tape 3 meters long. 21. white clad pocket steel tape 20 meters. 22. straight edge 10 cm. 23. pocket torch. 24. data book with pen. 25. calculator (scientific). 26. glass fiber safari well padded box with lock & key arrangement provided with well cushioned double decker system to avoid loss &damage of instruments [ warranty period: 30 months after the date of delivery ] ]

CTN :45594037

03 Jul, 2026 1.28 Lacs

Muzaffarnagar - Uttar Pradesh

Tender For supply of hss tool bit 1 , hss tool bit 2 , hss tool bit 3 , hss tool bit 4 , hss tool bit 5 , outside caliper , inside caliper , hss tapper dril 1 , hss tapper dril 2 , hss tapper dril 3 , hss tapper dril 4 , hss tapper dril 5 , flat file 1 , flat file 2 , steel scale 1 , steel scale 2 , carbide tool bit 1 , carbide tool bit 2 , carbide tool bit 3 , outside caliper , inside calipe , knurling tool , center drill bits , carbide tool bit

CTN :45354796

17 Jun, 2026 NA

Shekhapura - Bihar

Tender For bid to ras supply of bench top meter for measurement , electronic balance , benkelmen beam , centrifuge extractor , radar gun , deval abrasion value , ultra sonic pulse velocity instrument , torsion testing machine , spring material test , core cutting machine with drill bit , beam deflection appratus , strain gauge indicator , weight hanger , wind tunnel , open channel flume , friction loss along a pipe , minor losses in pipe appratus , reynolds apparatus , universal milling machine , mechanical press , resistance spot welding , welding hand shield , welding helmet , welding helmet auto darkening helmet , tool and cutter grinder machine , hydraulic hacksaw machine , gas cylinder filled with argon gas for tig welding , gas cylinder filled , crucibles set , pouring ladles , crucible tongs , slag spoons and skimmers set , indoor ducted chimney with furnace , moulding box , bernoulli theorem demonstration module , energy losses in pipes , fluid friction measurement , orifice and mouthpiece flow apparatus , orifice and venturi meter demonstrator , pitot tube apparatus , determine meta centric height , notch tank apparatus , determine density and viscosity of oil , determine critical reynolds number of tube , free and force vortex flow apparatus , impact of jets on vanes , palton turbine test rig , francis turbine test rig , kaplan turbine test rig , centrifugal pump test rig , reciprocating pump test rig , performance of a two stage reciprocating air compressor , air blower apparatus , heat transfer coefficient of composite wall apparatus , natural convection heat transfer apparatus

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

State Government

CTN :45350976

03 Jun, 2026 1.60 Lacs

Udaipur - Rajasthan

Tender For supply of workshop tool- engineering scriber, sleeve cutter, dedh center) , combination pliers length 210mm , vde plier length 160mm and 200mm , long nose plier length 165mm , side cutting plier length 165mm , side cutting plier with cable striper length 165mm , circlip pliers internal, external st., bent nose capacity 19-60mm , threading taped and dies complete tape and round die set in box 1/16, 3/32, 1/8, 5/32, 3/16, 7/32. %, bsw-7nos , 145/16 38 216,1585-5 , tap handle (1/4, 3/81%2 , line tester-length 130mm , socket set with handle with external (size-8-31) , octagonal chisel length 200mm cuting edge 22mm , octagonal chisel length 200mm cutting edge 25mm , center punch length 100 125, 150mm) , hackson frame , hand oil pump capacity 250 , grease gun lever type capacity 300cc, piston size 11/12 , outside caliper (150, 200mm) , inside caliper (150, 200) , spring divider 150, 200mm) , bench vise fived base 75m , adjustable spanner longth 305mm and 255mm , adjustable spanner with soll grip length 105mm and 255mm , oum boot , air hose pipe for comprever , tong , screw gauge , wire gauge , claw hammer , pipe wise , extension cord , air gun use in nut bolting , fire extinguisher

Central Government/Public Sector

CTN :45145131

18 May, 2026 NA

Kannur - Kerala

Tender For supply of ms lab machineries/equipments grinding ,machine ,jig saw machine ,ball pin hammer ,grinding stone ,frest saw ,metal stick ,half round maker ,doming punches ,inside calliper ,outside caliper ,divider, spray gun (for spray paints) ,pvc hose ,swage block ,machine vice (6" jaw length) ,vernier calliper ,surface guage

CTN :45036193

05 May, 2026 NA

Delhi - Delhi

Tender For expression of interest document for supply and delivery of school requisites 2026 for secondary schools (design and technology) - supply and delivery of school requisites 2026 for secondary schools (design & technology) - angle grinder, band saw, bench drilling machine, bench grinder, circular saw, compressor, spraygun, drilling machine (portable), extension cable, hot wire cutter, jig saw (portable), metal lathe, planer / thicknesser, router (portable), sander -orbital, soldering iron, strip heater, welding machine, wood working lathe, abrafile frame, adjustable spanner, adjustable spanner, anvil, bench hook*, bench shear (guillotine), bradawl, carpenters mallet, centre punch, centre square, chisels- mortice, chisels- mortice, chisels -bevelled edge, chisels -bevelled edge, chisels -bevelled edge, chisels- firmer, chisels- firmer, chisels- firmer, cold chisels, combination drill, combination pliers, coping, saws, corner clamps, countersunk bit, dividers, engineers square, engineers vice, forstner bit, g cramps, g cramps, hacksaw, hammer: ballpein, hammer: ballpein, hammer: ballpein, hammer claw, hammer cross pein, hand drill, hand files including handles, hand files including handles, hand files including handles, hand saws, hand saws, inside calipers, jack plane, jenny calipers, junior hacksaw, machine vice, marking gauge, marking knife, measuring tape, metalwork bench, mitre box, mole grip, nail punch, needle files, oil can, oil stone, outside calipers, pincers, pipe wrench, rasps, ring spanner, riveting machine kit, router bits, sash cramps, saw set, screw driver, screw driver, scriber, sliding bevel, smoothing plane, spanner - open ended, spirit level, spoke shave, spoke shave, steel rule, taps and dies, tenon saws, tinmans snip, tinmans snip, try square, v-block and clamp, vernier calliper, wire brush, woodwork bench, woodworkers bench vice, blackboard compasses, blackboard protractor, blackboard rule, blackboard set squares, design tables, isometric-grid blackboard*, square-grid blackboard*, whiteboard compasses, abrafile blades, coping saw blades, emery cloth, emery cloth, emery cloth, goggles, hacksaw blades, junior hacksaw blades, masks - respiratory, masks - dust, paint brush*, paint brush*, paint brush*, welding apron, welding gloves, welding rods.

CTN :44345613

30 Apr, 2026 3.5 Thousand

Bengaluru - Karnataka

Tender For corrigendum : procurement of machinery and equipment - inside caliper (divider)150, machine .brushes., bench. brushes., file,brushes., hacksaw .frame fixed 300mm., needle .file set., knurling .tool straight & diamond cut., hss .centre drill dia 8 mm., hss .centre drill dia 3.0 mm., hss .counter sink bit 120 degree., hss die .m4 - m12 with die stock., hss drill bit .straight shank dia 3 to 12 mm (step of 0.5 mm) (set)., goose neck .clamp set., strap .clamp set., machine .vice 150 mm (drilling)., self centering drill chuck 12 .mm., bench .grinder., dia .indicator - 0.01mm with styallus (needle type)., radius .gauge from 7.5 -15mm., thread .pitch gauge metric & inches., surface .plate granite 600 x 600 x 80 mm with stand., number .punch 5 mm set., pillar drilling. machine., cnc .simulators., outside .caliper (divider) 150, hammer .cross peen 0.75 kg with handle, flat .chisel, hss hand .hacksaw blade 18 tpi, magnetic .v block, rotary .table, sleeves .mt 3, sleeves .mt 2, sleeves .mt 1, materail .handling equipment, feeler .gauge 0.05 to 1.0 mm, radius .gauge upto 7mm, vernier .bevel protractor, universal .magnetic dial stand, outside .micrometre 25-50 mm, outside .micrometre 0-25 mm, dial .vernier 150 (0.02 lc), digital .vernier 0 - 150 mm, vernier .caliper 0 - 200 mm, vernier .caliper 0 -150 mm, vernier .height gauge 300 mm, center .punch, scriberr, try .square 4 inch blade, divider .spring type -150 mm, cnc cylindrical grinding machine., tool presetter , hydraulic vice - l- 525 x w- 108 x 135mm , opend 175mm, lathe dog carrier - bent tail 2 , lathe dog carrier - straight tail 2 , inserts type shell end mill dia 63mm with inserts (30nos.) 3 box., solid carbide end mill four flute dia 12mm , solid carbide end mill four flute dia 10mm , solid carbide end mill four flute dia 8mm , solid carbide end mill four flute dia 6mm , solid carbide end mill four flute dia 5mm , solid carbide end mill four flute dia 4mm , ball peen hammer 250 gms & 500 gms, warding file smooth 6 , knife edge file smooth 6 , knife edge file smooth 8 , knife edge file second cut 6 , knife edge file second cut 8 , knife edge file second cut 10 , half round file smooth 6 , half round file smooth 10 , half round file second cut 6 , half round file second cut 10 , half round file second cut 12 , half round file bastard 12 , round file smooth 6 , round file smooth 10 , round file second cut 6 , round file second cut 8 , round file second cut 10 , round file second cut 12 , round file bastard 12 , triangular file smooth 6 , triangular file smooth 8 , triangular file second cut 6 , triangular file second cut 8 , triangular file second cut 10 , triangular file bastard 10 , square file smooth 6 , square file smooth 8 , square file second cut 6 , square file second cut 8 , square file second cut 10 , square file bastard 12 , hand file second cut file 10 , flat file rough 12 , flat file smooth 8 , flat file smooth 10 , flat file second cut 8 , flat file second cut 10 , flat file second cut 12 , flat file bastard 12 , convex milling cutter dia 63 x 6 radius x bore size dia 27 mm., concave milling cutter dia 63 x 6 radius x bore size dia 27 mm., t slot cutter with parallel shank dia 17.5x8mm width shank dia 8mm, hss parallel shank end mill dia 16 four flute, hss parallel shank end mill dia 12, hss parallel shank end mill dia 10, hss parallel shank end mill dia 8, hss parallel shank end mill dia 6, hss tool bit 1 x 1 x 6 - 8% cobolt, hss tool bit 3/4 x 3/4 x 6 - 8% cobolt, hss tool bit 1/2 x 1/2 x 6 - 8% cobolt, hss tool bit 1/4 x 1/4 x 6 - 8% cobolt, flat slab oil stone 25 x 52 x 150 mm, hss centre drill dia 4.0 mm, hss machine reamer ( straight shank)dia 6 - 10 mm., hss hand reamer with wrench - dia 6 - 10 mm, power hacksaw machine with blade (10nos.)., hss tap set for size m4 - m12 with wrench (set) & core drills for the above tap set, taper shank hss drill dia 20mm, taper shank hss drill dia 16mm, taper shank hss drill dia 14mm, clamp c 10 , clamp c 5 , too

CTN :44926927

27 Apr, 2026 NA

Delhi - Delhi

Tender For corrigendum : supply and delivery of school requisites 2026 - angle grinder-grinding wheel, diameter 110 mm , power range, 750w to 2000w, 240v + key (eu), band saw-table size 400 x 548, mm, 900 w or 340 x 335 mm, 350, w 240 v + blade and sense (eu), bench drilling machine-13mm, chuck, 240v, minimum table size, 260 x 180 mm + chuck key (eu), bench grinder-minimum 250 w,, 240v, circular saw-minimum 1.5kw,, 240 v + fence and cross-cut guide, (eu) (table mounted), compressor -output 50l/min, 6, bar, 340 w + supply hose and clips, (eu), spraygun-0.7 mm nozzle, diameter, 800 cl capacity (approx), (0.7 mm - 1.4 mm), drilling machine (portable)-, chuck diameter 3 - 16mm, 240 v +, chuck key, extension cable-20 metres, hot wire cutter-40 w, 240v, jig saw (portable)- power range, 300 600 w, 240v + allen, key(eu), metal lathe-1.5kw, distance, between centres 750 mm, including tool bit, boring bar,, knurling tools, parting tools, tail, stock, chuck key, centre drill, dead, centre, revolving centre, face, plate, 4-jaw and 3-jaw chucks., (eu), planer / thicknesser-maximum, planing width 310mm,maximum, thicknesser capacity 230, mm,power range 3kw to 4kw,, 240 v + fence(eu, router (portable)- power range, 1200w to 1800 w, 240v + key, (eu), sander orbital-power range 250, w to 300 w, 240v (eu), soldering iron-80 w, strip heater-140 w, 240v, welding machine-electric arc, 6kw, 150a, 240v (with protective, casing) incluing clamp, cables and, shield. (eu), wood working lathe-distance, between centres 1093 mm, 550, w, 500 - 2000 revolutions per, minute including face plate, dead, centre, revolving centre, turning, tools and tool rest., abrafile frame-4" deep/blade, length 6" (+ blade on frame), adjustable spanner-jaws open : 22, mm length: 200 mm, adjustable spanner-jaws open : 31, mm length: 300 mm, anvil-50kg, bench hook*-material: beech, size:250 mm x 150 mm, bench shear (guillotine)- up to 4, mm sheet and 10 mm rod, bradawl-minimum blade length, 32 mm, carpenters mallet-4.5 head width, centre punch-round head,, knurled body, 4" length, centre square-std size 75 mm, chisels- mortice-size: 6 mm, chisels- mortice-size: 9 mm, chisels -bevelled edge-size: 12, mm, chisels -bevelled edge-size: 19, mm, chisels -bevelled edge-size: 25, mm, chisels- firmer-size: 6 mm, chisels- firmer-size: 12 mm, chisels- firmer-size: 25 mm, cold chisels-type: flat, size:150 mm x 12 mm, combination drill-std drill set, combination pliers-size: 200 mm, coping saws-blade length: 150, mm, corner clamps-cramping capacity, 4" mild steel type, countersunk bit-head diameter:, 3/8" length: 2", dividers-length 6", engineers square-length 6", engineers vice-jaw width: 6", engineer's swivel base table (50, mm), forstner bit-bit set: sizes 10, 12,, 15, 16, 18, 20, 22, 25, 26, 28, 30,, 35, 40, 45 & 50 mm, gcramps-capacity: 6", gcramps-capacity: 12", hacksaw-non-adjustable 12", tubular frame wing nut tensioning, device for 12" blades, hammer: ballpein-0.5 lb, hammer: ballpein-0.75 lb, hammer: ballpein-1 lb, hammer claw-0.5 lb, hammer cross pein-0.75 lb, hand drill-chuck capacity 8 mm, hand files including handles-size:, 6", hand files including handles-size:, 8", hand files including handles-size:, 10", hand saws-22" long - cross cut, hand saws-22" long -rip, inside calipers-arm length 6", jack plane-14" long, jenny calipers-arm length 6", junior hacksaw-length blade 6", machine vice-maximumm jaws, opening 85mm, marking gauge-minimum length, 240mm, marking knife-length of body, 15cm, measuring tape-measuring length:, range 3m to 5 m, metalwork bench-size 2010 x 810, x 800mm, mitre box-mitre block 9" long, (plastic), mole grip-length 7, nail punch-set of 4 nail punches;, 1.5, 2.5, 3 & 5 mm, needle files-set of 6 - 14cm, oil can-2 pints capacity (1-2 pint), oil stone-150 mm length, outside calipers-arm length 6", pincers-length of body: 180 mm, pipe wrench-length: 300 mm, rasps-length size: 200 mm - 350, mm, ring spanner-set 6mm 25mm, riveting machine kit-sets rivets, up to 5 mm

Outside Caliper Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government And Public Sector

State Government

Central Government/Public Sector