Latest pcc foundation Tenders | Government pcc foundation Tenders

State Government

CTN :45275642

02 Jun, 2026 3.07 Lacs

Serampore - West Bengal

Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging

CTN :45318277

09 Jun, 2026 50.00 Lacs

Godhra - Gujarat

Tender For supply of cooling pad 2 feet x 4 feet with fitting , cooling pad frame alluminium 2 feet x 4 feet , water circulation pipe for pad frame , repairing fogger system with fogger and material , green net , insect net , gi profile with installation , zigzag spring with installation 8 mm , fogger with lpd with installation , uv stabilized film , uv stabillized film greennet insect net installation labour , exhaust fan with installation , 15 w solar street ligh system set with installation , 15 w solar street light repering work , motor repairing 1.5hp , 2 hp three phase exhaust fan motor repairing , 2 hp three phase exhaust fan new motor with installation , gi pipe 1.5inch 2 mm thikness with fitting , gi pipe 2inch 2 mm thikness with fitting , repairing of panelboard , 2 core 4 sq cable with fitting , 3 core 4 sq cable with fitting , 4 core 4 sq cable with fitting , fiber or pvc gutter with fitting , temperature controller with fitting , humidity display with fitting , fogging auto controller with fitting , bedsheet 100 micron , fabrication work , electric work , plumbing work upvc pipe and fitting 50 mm , plumbing work pvc pipe and fitting 63 , micro irrigation facility for plantation , micro irrigation facility for hitech nursery , 16 mm lateral with installation , 16 mm inline with installation , 8 lph dripper with fitting , inverted modular sprinkler or fogger sytemt for nursery , installation of foundation pipe pole digging and civil material without pole , hp solar controllar , hp solar motor pump , 545 watt solar panel with fitting , 50 mm10 kg isi hdpe pipe , remove damage uvsheet greennet insecti net profile

CTN :45304567

08 Jun, 2026 4.60 Lacs

Thiruvananthapuram - Kerala

Tender For one panchayath one playground - development of vankulathuvayal stadium in azhikode grama panchayath in azhikode lac, kannur -supply and installation of outdoor gym equipment - supply and installation of horse rider having the following specifications: dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon / hdpe material. remaining frame is made by 48 mm od b class gi pipe. seat frame is made by 48 mm od b class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od b class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od b class gi pipe. paddle vertical support - 60 mm od b class gi pipe. handle frame- 42 mm od b class gi pipe dually bending design. foot pipe - 33 mm od b class gi pipe. support frame 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe. bearing bush closing cap pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand. bearing bushes - 60mm od seamless pipe. pin made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od405586/2025-2026 leg press (double) - specifications: dimensions: (l x w x h) = 1676 x 400 x1500 mm. main frame - 114 mm od ?b? class gi pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. foundations cover cap - dome shape of pp / nylon / hdpe material. link - is 60 mm od b? class gi pipe. seat frame - 42 mm od b class gi pipe. leg press back rest should be angled in 120 -130 degree. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 2 mm thick use to support it. seat & back rest ? 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 integrated wall thickness 3 to 4 mm. link connected with frame by 8 mm thick laser cutting ms profile. top closing cap ? dome shape made by pp / nylon / hdpe material. closing cap?s- pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing- use is 6005 permanent lubricated reputed brand. pin 25 mm m.s. bright bar pin. bearing bushes - 60 mm od seamless pipe. circlip? a 24 circlips are used for assembly. coating - best quality of powder coating 80 -120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od405583/2025-2026 back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od b class g.i. pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od b g.i pipe. seat rest pipe 42 mm od b class g.i pipe. handl

CTN :45306403

30 May, 2026 30.78 Lacs

Faridabad - Haryana

Tender For beautification and development of undeveloped park through plantation of grass, shrubs, open gym, children play equipment etc. in gali no.54 sanjay colony, ward no. 5, faridabad. - transportation all items, installation charge all items, p/f chest press is made from is-1239 b class gi-pipe. the center pipe is of 100mm nb made from b class gi-pipe, and the bottom support is of ms round plate of 250mm dia and 10mm thick is welded at the bottom of the pipe. the remaining frame is made of 32mm nb b class gi-pipe. the handle frame and seat is made of 32mm nb b class gi-pipe. connecting rod is made from 25mm nb b class gi-pipe. seat is made from roto-moulde. for the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used., p/f seated puller is made from is-1239 b class gi-pipe. the center pipe is of 100mm nb made from b class gi-pipe, and the bottom support is of ms round plate of 250mm dia and 10mm thick is welded at the bottom of the pipe. the remaining frame is made of 50mm and 25mm nb b class gi-pipe. the handle frame and seat is made of 32mm nb b class gi pipe. connecting rod is made from 25mm nb b class gi-pipe. seat is made from ms sheet of 2mm thick. for the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used, p/f sky walker is made from is-1239 b class gi-pipe. the center pipe is of 100mm nb made from b class gi-pipe, and the bottom support is of ms round plate of 250mm dia and 10mm thick is welded at the bottom of the pipe. the remaining frame is made of 50mm nb b class gi-pipe. the handle frame is made of 25mm nb b class gi-pipe. foot rod is made from 50x50 ms square pipe of 3mm thick. for the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used., p/f air walker is made from is-1239 b class gi-pipe. the bend pipe is of 80mm nb made from b class gi-pipe, and the bottom support is of ms round plate of 250mm dia and 10mm thick is welded at the bottom of the pipe. the remaining frame is made of 25mm nb c class gi-pipe. the leg frame is made of 32mm nb b class gi-pipe. for the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used. the foundation used for fixing it consist of three equal items i.e. 80mm nb made from b class gi-pipe, ms round plate of 250mm dia and 10mm thick,, p/f horse rider is made from is-1239 b class gi-pipe. the center pipe is of 100mm nb made from b class gi-pipe, and the bottom support is of ms round plate of 250mm dia and 10mm thick is welded at the bottom of the pipe. the remaining frame is made of 32mm nb b class gi-pipe. the handle frame and connecting rods is made of 25mm nb c class gipipe. seat frame is made from 32mm nb b class gi-pipe. seat is made from ms sheet of 2mm thick. for the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used. the foundation used for fixing it consist of three equal items i.e. 80mm nb made from b class gi-pipe, ms round plate of 250mm dia and 10mm thick., p/f leg press is made from is-1239 b class gi-pipe. the center pipe is of 100mm nb made from b class gi-pipe, and the bottom support is of ms round plate of 250mm dia and 10mm thick is welded at the bottom of the pipe. seat frame is made from 32mm nb b class gi-pipe. seat is made from ms sheet of 2mm thick. for the assembly different bushes are used which is made from 60mm with 3mm thick seamless pipe is used. the foundation used for fixing it consist of three equal items i.e. 80mm nb made from b class gi-pipe, ms round plate of 250mm dia and 10mm thick, p/f push-up-bar is made from is-1239 b class gi-pipe. the center pipe is of 100mm nb made from b class gi-pipe, and the bottom support is of ms round plate of 250mm dia and 10mm thick is welded at the bottom of the pipe. the remaining frame is made of 32mm nb b class gi-pipe. the foundation used for fixing it consist of three equal items i.e. 80mm nb made from

CTN :45302756

06 Jun, 2026 NA

Khurda - Odisha

Tender For supply of surface dressing levelling and top soil spreading , modular interlocking paver rubberised walkway tiles on sand bed , hedge plantation including manure and initian care , lawn development with ready turf and soil conditioner , shrubs and seasonal flowering plants , large ornamental potted plants with frp ceramic planters , prefabricated modular foundation fountain base dia 14ft x 8ft height , prefabricated mural panel 8x14 ft on sms bolt fixed frame , naval themed decorative artefacts insignia , led accent wall washer lights for murals , decorative wall panelling laminated cladding , naval heritage display panes framed , partial detachable false celling panels , ambient and feature led lighting , indoor planters and decorative element , decorative pole light base plate mounted including cabling connectors switche and earthing , outdoor benches seating modules , waste bins utilities stand , directional and safety signage , maintenance and upkeep services

CTN :45274954

28 May, 2026 NA

Ranchi - Jharkhand

Tender For dismantling and removal of led screens along with all associated accessories, feeder pillars, wires, cables, and ms frame structures/pillars including foundation, as well as disconnection of electrical cables of the led screens as per applicable electrical norms."at morabadi ground, ranchi, jharkhand

corporations/Associations/Others

CTN :45277495

28 May, 2026 4.67 Lacs

Chandigarh - Chandigarh

Tender For providing and fixing of open air gym equipments in various parks of sector 20,chandigaarh under ward development fund. - providing and fixing of chest press double size / dimensions length -1200 milimeterwidth- 700 milimeterheight 1800 milimetermaximum weight -120 kilogrammaterial:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength, durability, and corrosion resistance. the main central pipe shall be an 80 mm nb gi pipe, while the handle frame and sheet frame shall each consist of 40 mm nb gi pipes. the connecting links shall be made of 32 mm nb gi pipes, and the footrest pipe shall also be 32 mm nb gi. the mild steel (ms) foundation plate shall have a minimum thickness of 12 mm. the foundation pipe shall consist of a gi pipe anchored 750 mm deep and supported with an ms angle of 25 25 4 mm for stability. the seat and backrest shall be made of high-density polyethylene (hdpe) sheets with a thickness of 3 mm, designed with a uniform bending radius to avoid sharp edges and ensure user safety. all nuts and bolts used for assembly shall be made of galvanized iron (gi) to enhance durability and resistance to corrosion. the movement mechanism shall be fitted with ball bearings that are self-lubricating and sealed to protect against rain, dust, and other environmental elements. the closing caps of open ends of all pipes, as well as bearings, bushes, and bases, shall be covered with fibre-reinforced plastic (frp) closing caps having a minimum thickness of 3 mm. all plastic components shall be uv-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.colour:- green paint finish- power coated, uv resistantpaint coating thickness (min) 100 micrometerwarranty 3 years.complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of leg press leg shaper complete in all respects having following specifications.a) all pipes should used in the equipments should be galvanised with 3mm thickness.b) multi colour powder coating with polyster paints should be used on all the equipments.c) the foot pedal on all the equipments should be of aluminium only.d) the seats should be made of high quality plastic with colour scheme in yellow or orange.e) the high end bearings such as skf/nbc must be used in all the equipments.1 dimensions- 1730*450*1450mm2 colour- customizable multi colour and complete powder coat3 size of main tube-114*3.75mm steel pipe4 size of supporting tube-76*3mm steel pipe5 there is restrainer inside, the distance between swing arm and main tube is greater than 230mm avoiding the danger of getting stuck.6 al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 anti-skid components are used at the pedal parts.8 the distance between two spinners is no less than 230mm, avoiding the damage of being stuck9 anti theft cover is made by stainless steel/high quality plastic.10 thickness of bearing bracket is no less than8mm11 hazardous materials like coating agent, rubber are under national newest standard.functions: develops the strength of lower limbs, and improves the stability and agility of three main joints of lower limbs; good for the healing of inconvenience of bending and stretching of lower limbs, and muscular atrophy of lower limbs, rheumatoid arthritis, sciatica, sprain of the anklebone, etc. approaches: sit on the chair and step on the footboard. stretching legs with force and recover slowly. repeat. users: suitable for people of different ages.complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of parallel bars size/dimensionslength- 900 millimeterheight 800 millimetermaterial:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength and durability. the ver

CTN :45148599

26 May, 2026 NA

West Kameng - Arunachal Pradesh

Tender For bid to ras supply of climbing wall for rock climbing training with total climbing surface area 600 sqftheight , ms frame structure frame work subsidiary frame work with anchors , raft foundation for climbing wall , painting for steel structure and panels with two coat of red primer , complete installation , climbing rope dynamic 9.8mm , seat harness universal size , screw carabiner jumbo , screw carabiner regular size , chalk powder , chalk bag , climbing holds movable , chain anchors , helmet

Central Government/Public Sector

CTN :45139024

01 Jun, 2026 NA

Mysore - Karnataka

Tender For design, supply, foundation, installation, testing , commissioning training and proving out of hydraulic c frame press machine -100ton capacity along with warranty(warranty includes preventive maintenance schedule (pms) 8 quarters as per the format enclosed as per annexure b) as per the technical specification annexure a enclosed. [warranty period: 30 months after the date of delivery) [ warranty period: 30 months after the date of delivery ]

CTN :45252275

09 Jun, 2026 NA

Mumbai - Maharashtra

Tender For supply of dewatering pump , dismentaling pumps , dismentaling starters , removal of piping , removal of frame , foundation frame , installation of frame , civil work for frame , piping material , installtion of piping , flow meter , pressure transmitter , pump and motor installtion , piping work , electrical work , inspection of pumps , commissioning of pump , electrical central control panel

Pcc Foundation Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

corporations/Associations/Others

Central Government/Public Sector