Tender For custom bid for services - defect rectification of acsr 2 (south tower)-defect., in has reported that tracks are not available on display of acsr #2., defect identification., di for the same was undertaken on 13 jun 2025. it was found that the pedestal unit, was required to be replaced to rectify the defect., scope of work to undertake defect rectification., 1. spare part., the required pedestal unit for replacement will be provisioned by in on site. all other, components/ units of acsr #2 should be in place to operationalize the system., 2. manpower., three skilled technicians will be required to undertake the pedestal replacement work., one tower climber also needs to be available on site. the tower climber and two, technicians will be provisioned by hela., 3. material/ machinery., one overhead crane with a loading capacity of one ton lifting to a height of 35 mtrs is, required to undertake the work. the same will be provisioned by in., 4. tools and accessory., the following are required and will be provisioned by hela:-, (a) torque wrench, (b) level indicator, (c) eye hook -02, (d) two 50 mtrs rope, (e) silicon, (f) drill machine, (g) lubricant, (h) slings for lifting, 5. activity to be undertaken., the sequence of events for replacement of pedestal unit will be as tollows:-, (a) disconnect and remove all cables, wave guide ard units from the antennae assembly., (b) fitment of lifting eye hook on antenna and pass lifting slings to the eye hook. dismantle antenna from pedestal unit and keep it on even surface on, the ground with the help of overhead crane. special care is o be undertaken while handling waveguide., (c) hook on the pedestal unit on overhead crane and op an securing bolts, of pedestal unit. lift the pedestal and move to the ground with cap closed of all connectors., (d) hook up new pedestal and lift it to the tower top and w hen aligned with, the position of pedestal plate lower the pedestal on the plate and tight the nut, bolt with level indicator on top of the pedestal to confirm tht the same is at, zero level., (e) lift the antenna to the top of tower and fix it to the pede stal unit., (f) install all units of acsr on top of tower and fix connectors and waveguide to the antenna., (g) switch on power and carry out power checks and fo (hecks., (h) switch on the acsr server and carry out alignment of system to get the tracks appeared on the display., 6. safety., all man working on tower should wear safety belt, safety helmet and safety belt to be, tied on two rigid point at tower top. the man below tower for handlin activity should, wear helmet. the antennae assembly and pedestal unit should be se cured with twopoint safety rope while lifting and lowering the same to avoid any dan age to the man, and material view heavy wind, lifting jerk or swing of the crane sling., .
Tender For corrigendum : supply of field coil assy , self armature , self bush , brush carrier , caliper pad assy , safety plug , eng mtg pad , center bolt , wiper blade , accelerator cable , tmap sensor , knuckle bearing , brake shoe revit , self bendix pinion , bush set self , radiator cap , axle tube hub seal , hub oil seal , alternator drive belt , tail lock inner catch , ball joint lower arm , ball joint upper arm , tie rod end , suspension bush kit , tie rod ball joint link rod , radiator assy
Tender For supply of 3d printer,computer for 3d printer,ups online 30 kv,3d printer filament,anti drone jamming gun,practice drone,multirotor drones with day camera,fpv trg drone 7 inch,kamikaze trg drone 10 inch,kamikaze trg drone 5 inch,ultimate rc tool kit for fpv drones,vr goggles works with all fpv drones,simulator software with compatible remote,pc for simulator,ups for pc,drone programs techanical support and associated services,strap belt for bty,soldering machine with paste and wire,bty voltage checker,multimeter,propeller balancer,first aid kit,fire safety equipement,hdmi cable,hdmi to c type,hdmi lightening cable apple,extension board,spare parts accessories fpv goggles for 7 inch fpv trg drones,spare parts accessories fpv goggles for 10 inch kamikaze trg drones,spare parts accessories fpv goggles for 5 inch kamikaze trg drones,spare parts accessories cameras payload dropping mechanisms,spare parts drone accessories for multi rotor,addl goggles and rc
Tender For bid to ras corrigendum : supply of trouser , shirt full sleeves , t shirt , blazer or half coat , jacket , tie , formal shoes , socks , belt , name badge , bag pack , rain coat , hard hat or helmet , h v vest , safety shoes
Tender For supply of spares of hydraulic mobile crane d d - hyd gear pump , fuel filter element , lof cartridge , safety element , element air filter , vacuator valve , fan belt , filter tc , strainer , filter element , air breather assy , relay 24 v , leak o pipe sub assy , spin on filter for lubricating oil , joint for rocker cover , repair kit , accelerator padel , kit , fuel pipe , flexible fuel pipe , copper washer , supply
Tender For brushless alternator of 25kw capacity 'v' belt driven on both end suitable for use on 11 0v dc air condition coaches fitted with under frame mounted conventional ac plant as per following s cope of supply:- 1)25 kw brushless alternator as per rdso spec no. rdso/pe/spec/ac/0056-2014 rev .1 - 1 no. 2) deep 'v' groove (6) alternator pulley as per rdso spec no. elps/spec/tl/13-mar-98 & r dso's drawing no.skel-3645(rev.4)-2014 -2 nos 3)deep 'v' groove (6) axle pulley with rubber pad as per rdso spec. no. elps/spec/tl/13 mar-98-2 nos. (4) safety chain: 3 nos. (5)suspension pin with fa stener etc. as per drawing no. skel-3943 (rev-2)-2016, alt-1 (suspension pin length increased from 5 77 mm to 613 mm) : 1 no. (6) belt tensioning device assembly : 2 nos. [ warranty period: 30 mont hs after the date of delivery ]