Latest pin punch Tenders | Government pin punch Tenders

State Government

CTN :45275642

02 Jun, 2026 3.07 Lacs

Serampore - West Bengal

Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging

State Government

CTN :45287473

28 May, 2026 NA

Chandrapur - Maharashtra

Tender For procurement of spares of bottom ash hopper feed gate, hydro ejectors and liners for clinker grinder during u#8 aoh at ash handling plant cstps, chandrapur. - 85tph liner pn be1440d-01, 85tph liner pn be1440d-02, feeder ejector ayems inlet liners, slight glass assly size-3/4" n3922, hopper driplex inspection glass 220 mm, macawber beekay gland follower, bearing cover (1 set = 4 nos.) be1435d, bearing block (1 set = 4 nos.)be1434d, spur gear be1437d, shaft stuffing block be1431d, gate liner for door frame thick 24 mm, gate liner thickness 14 mm, fed gate side guide plate pn be5064d, fed gate flood light assly be3749d-02, complete feed sump assembly with liner, throat & discharge piece(be 3261d-03), fed gate bracket,pin &piston rod clevis, feed gate cylinder assy pn be4865d, feed gate tecpro sys power cyl seal set, ahp basys fdgate guide rail, fed gate lower wedge be1121d-b, fed gate upper wedge be1121d-a

Central Government/Public Sector

CTN :45214195

30 May, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of stationery -clips gem packet of 100 nos , eraser pencil , gum bottles 700 ml , gum tube 30 ml , ink stamp pad bottle of 25 ml , pad stamp medium size , pencil hb , alpins nickel coated in packets , pins stapler (packet of 1000 pins) , punching machine single , rubber bands 25 grm packet of assorted , scale plastic size 300 mm , stappler , stencil foolscap (packet of 50 sheets ) , tray plastic 36.5x27x5cm , twine bundle (ball) make common standr , tag bundles 6 tags , pin drawing packet to be supplied in pkt , rubber bands 100 grm packet of assorted

CTN :45203547

18 Jun, 2026 20.00 Lacs

Chhindwara - Madhya Pradesh

Tender For supply of stationery and printing work item year 2026-27 - a4 size paper (75 gsm), a4 size paper (80 gsm), a3 size paper, legal size paper, file covers (soft/hard), plastic files/folders, registers (1 quire), registers (2 quires), registers (3 quires), registers (4 quires), spiral notebooks, ballpoint pens, gel pens, refills, pencils, erasers, sharpeners, cd markers, whiteboard markers, permanent markers, highlighters, correction fluid/whitener, small staplers, large staplers, small staple pins, large staple pins, punching machines, paper pins, binder clips, paperweights, glue/adhesive, glue sticks, brown tape, cellophane tape, double-sided tape, carbon paper, small envelopes, medium envelopes, large envelopes, registered post envelopes, parcel covers, tags/cotton thread, sticky notes, index files, postal registers, cash books, ledger books, printed forms, receipt books, visitor registers, inward/outward registers, paper trays, file trays (in/out), dusters, whiteboards, whiteboard dusters, whiteboard ink, printer ink/toner, spiral binding materials, lamination sheets, diaries, scissors, small tape dispensers, large tape dispensers, medium calculators, stamp pad ink bottles.

corporations/Associations/Others

CTN :45171789

26 May, 2026 NA

Salem - Tamil Nadu

Tender For supply of spares for gravimetric feeders 7 items - feeder head pulley half coupling, feeder head pulley half coupling pin with lock nut & spring washer, feeder spares 1 set consists of i) belt tensioning guide block, ii) belt tensioning bush,iii) belt tensioning screw,, shear pin, idler bearing cup, rubber logged gun metal bush, head pulley bearing cup with retainer flange and plate

State Government

CTN :45279132

04 Jun, 2026 1.66 Crore

Udhamsign Nagar - Uttarakhand

Tender For work of construction of a new 11 kv feeder for bifurcation of overloaded 11 kv chakarpur feeder under edd khatima in capital s.i. head, including supply of decentralized materials, as per tender specification. - annexure-a (supply of following material as per upcl norms.), bracing clamp for sp-55 with nut and bolt., pp & clamp with nut and bolt st pole sp-55., stay clamp for sp-55 with nut and bolt., pp & clamp with n&b st pole sp-72., pp & clamp with n&b pcc pole, 8.5 mtr., stay clamp for pcc pole., ht stay insulator., 33 kv suspension ties on every pin insutlator., ipc with aluminium bail for earthing., 11 kv ipc for covered to covered cond., 11 kv ipc for covered to bare conductor., 11 kv mid span jointing kit., 11 kv aaac covered cond. al-59, 99 sq.mm., 11 kv tension clamp with bail & ipc., annexure-b (following work as per upcl norms), chemical earthing., fabrication of steel., excavation of pit for stay set., erection of 11 kv stay set,, grouting of stay set., excavation of pit for pole., erection of single pcc pole., erectin of single sp-55 pole., erection of single sp-72 pole., erection of pcc double pole., erection of sp-55 double pole., grouting of pole., muffing of pole., painting of sp-55 pole., lopping and choppong of tree branchases., cartage of pcc pole, 51-70 k, cartage of sp-55 pole, 51-70 km., cartage of sp-72 pole, 51-70 km., cartage of petty material, 51-70 km., headload cartage of pcc pole, 0-1 km., headload cartage of sp-55 pole, 0-1 km., headload cartage o sp-72 pole, 0-1 km., headload cartage of material, 0-1 km., fixing of 33 kv suspension ties., fixing of ipc with al, bail for earting., jumpering of d/p tpmo, fuse set and t/f., jumper section pole., fixing of 11 kv 90 kn tension clamp b&ipc., fixing of 11 kv ipc for cc to cc cond., fixing of 11 kv ipc for cc to bare cond., fixing of 11 kv mid span jointing kit., laying spreading, stringing aac conductor

CTN :45298003

05 Jun, 2026 NA

Paschim Medinipur - West Bengal

Tender For supply of xlpe cable for working voltage up to and including 1.1 kv marked to is 7098 (part 1) (q2) , moulded case circuit breakers (mccb) conforming to is/iec 60947 (part 2) (q2) , miniature circuit breakers (mcb) for ac operation marked to is/iec 60898 (part 1) (q2) , led luminaire for floodlight conforming to is 10322 (part 5/section 5) (v3) (under bis scheme - ii) (q2) , supply and fixing switch socket combination 5 pin, 5 amps flush type. complete all as specified and directed in boq spec file , supply and fixing switch socket combination 2 in 1, 5 amps by 16 amps flush type complete all as specified and directed in boq spec file , supply and fixing distribution board db vtpn 6way out of sheet metal enclosure.complete all as specified and directed in boq spec file , supply and fixing distribution board db tpn 4 way made out of sheet metal enclosure complete all as specified and directed in boq spec file , supply and fixing distribution board db spn 8 way made out of sheet metal enclosure complete all as specified and directed in boq spec file , supply fixing and conmmissioning of one heavy duty plus 30 mtr high mast pole fabricated from hot dip gi steel in three section bottom section of 10500 mm length complete all as specified , supply, installation, and commissioning of a feeder panel for a 30 m high mast lighting system with a load capacity of 7kv. , supply ,testing and commissioneng of lt control panel outdoor type of toe 1.6x1.5x0.75 m having provision of double door. complete all as specified and directed in boq spec file , supply and fixing earthing complete with galvanised steel earth plate tree 50-60cm x 6mm directly in ground.complete all as specified and directed in boq spec file , instalation, testing and commissioning of lt bus bar feeder piller box outdoor type having provision of double door openings.complete all as specified and directed in boq ) /bid number : gem/2026/b/7570938 * /dated: 22-05-2026 & & / bid document 1 / 32 spec file , supply and laying fly ash bricks well purnt old size designation 75 per 1000 laid dry flat for protection of cable.complete all as specified and directed in boq spec file , high mast electrical system,complete all as specified and directed in boq spec file , concealed point wiring complete using 1.5 sqmm pvc insultated sheathed copper cable frlsh 1100 volts , earth dolly for one 3 pin, 5 amps socket outlet in the independent board. , concealed point wiring complete using 2.5 sqmm pvc insultated sheathed copper cable frlsh 1100 volts , for power point on independent board. , supply of laying and digging excavation of foundation pit of size 5ft x 5ft x 5.5ft 4.5ft below ground level and 1ft above ground level complete all as specified and directed in boq spec file , supply and installation of minimum 3.3 tall meters triple lamp post features en attractive 19th-century lamp design.complete all as specified and directed in boq spec file , digging and laying removing excavated material soil not exceeding 50 m.complete all as specified and directed in boq spec file , returning filling in including spreading leveling watering.complete all as specified and directed in boq spec file , sand cushioning for ug cable 8 cm before laying the cable.complete all as specified and directed in boq spec file , supply of laying and digging in trenches by post holes in soft by loose soil not exceeding 1.5 mtr wide.complete all as specified and directed in boq spec file , material and labour of concealed three phase sub main wining using single core pvc insulated cable frls 4x10 sqmm copper conductor multi stranded and 1x10 sqmm copper conductor insulated cable , material and labour of concealed sup main wiring using two single core pvc insulated cable frls 6 samm copper conductor muti stranded and 6.0 sqmm copper conductor insulated cable frls

CTN :45252515

29 May, 2026 NA

Budge Budge - West Bengal

Tender For supply of needle roller bearing for plunger actuating pin for 12 nozzles volumetric filling machine , spring set of capping tool assembly for 12 nozzles volumetric filling machine , clutch liner for gearbox clutch for 12 nozzles volumetric filling machine , v-belt for main drive for 12 nozzles volumetric filling machine , needle roller bearing for groom cam follower pin for 12 nozzles volumetric filling machine , surface cam follower pin for capping tools for 12 nozzles volumetric filling machine , surface cam follower bearing-1 for 12 nozzles volumetric filling machine , surface cam follower bearing-2 for 12 nozzles volumetric filling machine , cylinder seal kit complete set for 12 nozzles volumetric filling machine , cam follower complete set with cam follower pin cam follower bearing for 12 nozzles volumetric filling m c , reflector sensor for cap feeder dia 18mm for 12 nozzles volumetric filling machine , difuse photoelectric sensor obd200 500 , proximity sensor 18mm , tank level sensor lfl 2 for 12 nozzles volumetric filling machine , rewinding roller assy set with shaft for sarac other labeling machine , dancing roller bracket assy set labeling machine , set of spring for dancing roller labeling machine , rubber roller only 225mm labeling machine , sponge roller 175mm labeling machine , set of chain wheel for top conveyor assembly labeling machine , bearing 6902zz, top belt sprocket side of labeling machine. , ball bearing 6202- 2z, rewinding roller base of labeling machine. , roller bearing hk1516, rewinding roller buttom of labeling machine. , bearing for dancing roller hk1512 of labeling machine. , bering for traction roller 608-2rs, hch, of labeling machine. , label sensor , product sensor with reflector , top conveyor stabilizing belt 900h without sponge , timing belt 160xl , timing belt 200xl , side belt for belt orientation , aluminium disk of label holder , tape cutter blade of carton sealing m c , tapping head lower tension spring of carton sealing , filling load cell up down cylinders for 3 nozzles bucket filling machine advu- 63.15- a-p-a, festo , filling stopper cylinders for 3 nozzles bucket filling machine dsnu-16-50-p-a , filling nozzle sealket set for 2 nozzle bucket filling machine , filling load cell up down cylinders for 2 nozzle bucket filling machine advu-63. 15-a- p-a , filling stopper cylinders for 2 nozzles bucket filling machine dzf-25-50-a-p-a , 5 head lube filling nozzle seal ket set , solenoide valve for 54 nozzle bucket filling m c, festo , 5 nozzle load cell model no 1042 mt make tedea

Central Government/Public Sector

CTN :45260723

30 May, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For supply of j bolt and spring for belt conveyors , square bolts, nuts and washers for ring granulator , coupling bolts & nuts for pin bush coupling of wagon tippler-1 to 5 , fastener for tension skirt board of vibrating screen(coal) -1 & 2 , m16x54 size fit bolt with nut for apron feeder(ore) , coach bolt assembly for vibrating screen-3, 4 & 5

State Government

CTN :45230884

21 May, 2026 NA

Chandrapur - Maharashtra

Tender For procurement of spares of bottom ash hopper feed gate, hydro ejectors and liners for clinker grinder during u#8 aoh at ash handling plant cstps, chandrapur. - 85tph liner pn be1440d-01, 85tph liner pn be1440d-02, feeder ejector ayems inlet liners, slight glass assly size-3/4" n3922, hopper driplex inspection glass 220 mm, macawber beekay gland follower, bearing cover (1 set = 4 nos.) be1435d, bearing block (1 set = 4 nos.)be1434d, spur gear be1437d, shaft stuffing block be1431d, gate liner for door frame thick 24 mm, gate liner thickness 14 mm, fed gate side guide plate pn be5064d, fed gate flood light assly be3749d-02, complete feed sump assembly with liner, throat & discharge piece(be 3261d-03), fed gate bracket,pin &piston rod clevis, feed gate cylinder assy pn be4865d, feed gate tecpro sys power cyl seal set, ahp basys fdgate guide rail, fed gate lower wedge be1121d-b, fed gate upper wedge be1121d-a

Pin Punch Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

Central Government/Public Sector

corporations/Associations/Others

State Government

Central Government/Public Sector

State Government