Latest plate lifting clamp Tenders | Government plate lifting clamp Tenders

CTN :42408674

01 Nov, 2025 NA

Delhi - Delhi

Tender For supply of cylinder liner with joint ring,washer,valve tappet,washer,push rod,bush for injector,bolt for mb cap m14x2x128,oil seal 115x140x16,oil seal,bolt,washer,banjo bolt,starter ring ha,pin,ammeter 50-0-50-amp,special banjo bolt,bolt for flywheel,washer for sump screw,hose clamp ss tbots n4 nut 115 mm,lo filter element,copper washer inj,compression ring for gas outlet manifold,injector yoke,drain plug with magnet o ring,thrust washer,lub oil pressure sendor gauge assy 12v0 10 bar,worm drive clamp 29 45 mm dia,screw with stainer,washer fip gear,rubber bush for oil fillling cap,thermostat element,o ring for injector,primary element,secondary element,fuel pipe return m12x105,fuel pipe inlet m16x1.5,sealing ring fuel filter,electrical lub oil pressure guage,v belt cogged bx 48,joint for turbo,thrust washer cam shaft,lo supply hose fip,cylinder head bolt,hose by pass,v belt xpa 1250 cogged,hose thermostat,spacer ex manifold,joint for adopter ring,fuel injector,banjo bolt for piston cooling nozzle,rubber hose turbocharger

CTN :41609769

13 Nov, 2025 NA

Delhi - Delhi

Tender For corrigendum : procurement of spares for il-78 aircraft - subassy, switch (s3) attaching parts, name plate, box assembly, connector circ. mount, relay, filtre element hydac, cap, filter element 5 ? absolute, filter element 10 ? absolute, two way filtered valve restrictor, cylinder, piston, shoulder ring, end cap, oil, screw cap, end cap, air, iso chain, l=61.25 (102 pitches), end cup, nameplate, block assembly, body (part of item 16.1), spool and sleeve assembly, sleeve, spool and sleeve assembly, spool, setscrew (opt to item 90), gear, worm attaching parts, plug, pin, cover attaching parts, sleeve, plate, cover attaching part, needle, valve, assembly, plate, cover attaching parts, it is a sub-assembly of hydraulic flow regulator, label, spool and piston subassembly, spool; compensator(matched set order nha item-290), cap-port s/a, plate - cam, piston, stroking, hud check valve, latch, name plate, name plate, pressure teflon hose, sleeve, bushing teflon, tube assy, tube assy, tube assy, tube assy, drain, pressure teflon hose, cover, body, shaft, splined, harness, harness, harness, harness, harness, body, assembly, o-ring, cam and piston s/a, piston and shoe s/a, bearing barrel, barrel cylinder, mounting flange s/a, pin cam index, front housing s/a, seal and retainer s/a, retainer-seal and bearing, shaft internal drive, bushing spline, spring-helical compression, washer thrust, plate hold down, spacer, bushing, cup (order nha item 6), piston, rate, barrel cylinder, actuator assy, shaft assy, switch assy (s2) attaching parts, switch subassy (s4) attaching parts, body, motor, machined, cam, cam, shaft, plug, cover, motor attaching parts, hex attaching parts, cover, cover attaching parts, cover attaching parts, tube, shaft, splined, plate, switch, stand off attaching parts, spacer, stand off, piston, blocking 9matched set order nha), port cap, seal, plain encased, washer (order nha item 6), terminal (96736 scd 99-1008-3), terminal (96736 scd 99-1008-2), nut, bracket, union, tee (pr12-02), box assy, box assembly, worm, machined, module, module, rail, grounding module, connector attaching parts, washer, flat, nitrogen filter, filter element, filter element, actuator (96736 scd 99-1127) attaching parts, o-ring, fluorosilicone, receptacle, it is a sub-assembly of light control box, connector circ. mount, bearing, cylinder barrel, diode, screw(g702410), rivet (alternate p/n), screw, pnh, self-locking, 8-32 thd x .250 lg, heli-coil insert, insert, screw thread, insert, screw thread, elbow, elbow, union,elbow (ar12-03), clamp, union, lug crimp, switch, micro, screw, relay, 2pdt, type i attaching parts, relay, screw, o-ring, packing performed, screw, washer lock, pin, bolt- machine, 12 pt. hd. (ap), pin, straight, .0937 dia attaching parts, screw, screw, nut, self-locking, screw, cap, socket head, 1900-32 thd x .875 lg, insert, cres helical coil, screw, cap, socket head, .1380-32 thd x .750 lg, clamp, screw, spacer, spacer, grommet, bolt, bolt, bolt, bolt, lee plug, tie up strip, relay, housing assembly, tensioning screw, bracket, chain wheel, axle, washer, name plate, angle, switch assy drogue limit, oil- eye, screw-socket head cap (ap), filter element, washer, wave (96736 scd 99-1011-2), absorber shock

Central Government/Public Sector

CTN :42095012

23 Oct, 2025 NA

Jorhat - Assam

Tender For corrigendum : supply of consumables for construction of hybrid energy device - mild steel sheet, 8ft x 4ft x 1.2 mm, mild steel angle rod, 1.5 inch x 20 ft, mild steel angle rod, 1 inch x 20 ft, mild steel welding rod, diameter: 3.15 mm, mild steel perforated sheet, 8ft x 4ft x 1.2 mm., stainless steel 304 sheet, 8ft x 4ft x 1.2 mm, stainless steel 304 perforated sheet, 8ft x 4ft x 1.2 mm, stainless steel 304 pipe, 1.5 inch dia, 1.5 inch dia, 1.2 mm, 20 ft, zinc alloy door handle lock, stainless steel 304 welding rod, 2.5 mm diameter, ceramic fibre blanket insulation, 24"x12"x1", ceramic fibre rope, 10 mm diameter, 30 m length, heat insulating gasket, 8 ft x 4 ft, 5mm thickness, heat resistant spray paint 225 ml, silicon pipe 1/2 inch inner dia, 10 m, high temperature silicon hose pipe, 2 inch inner dia, 12 feet, worm-drive tubing clamps.chrome steel, hose clamp, 1/2 inch dia, worm-drive tubing clamps.chrome steel, hose clamp, 1 inch dia, worm-drive tubing clamps.chrome steel, hose clamp, 2 inch dia, worm-drive tubing clamps.chrome steel, hose clamp, 3 inch dia, galvanized mild steel set of nut, bolt and washer, 8 mm diameter, 2 inch length, temperature sensor with digital display, k type, 0-1250 с, adruino uno r3 development board, rod heater, 8.2 mm diameter, 12 inch length, quartz furnace observation glass, temperature: 1200 °c, 10 em diameter, 5 mm thickness, copper tube 1/2 inch dia, 23 swg, copper electric wire 6 sq. mm, 90 m, copper electric wire 2.5 sq. mm, 90 m, mcb dp 32 a, electric socket 16 a, electric plug 16 a, combined box 20 a, anabond gasket maker 85 g, heavy load caster swivel diameter: 100 mm, galvanized iron pipe b class diameter: 1.5 inch, length: 40 ft, galvanized iron pipe b class diameter: 1/2 inch, length: 20, galvanized iron pipe b class diameter: 3/4 inch, length: 20 a, stainless steel 304 ball valve diameter: 1.5 inch, stainless steel 304 ball valve diameter: 3/4 inch, stainless steel 304 hall valve diameter: 1/2 inch, check valve, brass diameter: 1.5 inch, check valve, brass diameter: 3/4 inch, check valve, brass diameter: 1/2 inch, metal cutter grinder disc, pack of 10, grit number 220, diameter: 4 inch, grit material: aluminium oxide, metal cutter grinding wheel, pack of 5, grit number 4., diameter: 4 inch, grit material: aluminium oxide, flap disc, pack of 10, grit number 80, diameter: 4 inch, grit material: aluminium oxide, flexible heavy duty 3 layer pvc water pipe, diameter: % inch, length: 30 m, teflon tape for plumbing, pack of 10, 12 mm thick and 10 m length, heat resistant gloves, material: leather, size: 30.48 cm, nitrile disposable hand gloves, pack of 50 pieces, size: l, 150 microfarad capacitor, 230 v, 150 microfarad, 230 v, anti vibration rubber ribbed pads, pack of 4, 150mm x 150mm x 12mm, square pillow block bearing ucf204, 20 mm diameter, inner ball mounted pillow block insert bearing kp08, 8 mim bore, step down transformer, 220v ac to 12-0-12 v.1.5a, single strand wire, diameter 0.51mm,5m, moc3021 moc 3021 optocoupler, bta16-600b triac, 600v 16a, switch. sw-spst, in4007 diode, 100%via, bldc motor with compatible e-bike controller, 48v 900w 3300rpm, lithium-ion battery, a grade 3.2v 2000mah (5c), battery management system, li-ion 135 48v 20a, nickel strip, 0.2 mm thickness, 10 mm width, 5 m length, silicon wire, 12awg, insulation paper, 65mm, glue gun, 40 w, spot welding rod 5000 w, cpu fan 12 v dc, thermoelectric generator (teg), 150°c, module., configuration: sp1848-27145, tungsten rhenium thermocouple, minimum temperature reading: 0°c, maximum temperature reading: between 2300°c and 2871°c, max31856 instrumentation amplifier,, resolution: 0.0078125°c, supply voltage: 3.3v to 5v, arduino uno r3 with adapter cable, miniature circuit breaker fuse, d type, 32 a, power rocker switch, voltage rating: 24 vdc, current, rating: 14 ma, 19mm size red power symbol led s.s. momentary type, push button switch 5v-24v dc, potentiometers 100 kohm, potentiometers 1 m ohm, relay module-(ssr-2 cha

Central Government/Public Sector

CTN :42221299

27 Oct, 2025 NA

Perambalur - Tamil Nadu

Tender For supply of worm drive hose clamp

CTN :42186157

28 Oct, 2025 NA

Multi City - Multi State

Tender For supply of set ss worm drive hose clamp for lhb coaches consisting of 03 items as per annexure, as per is:4762/2002, material specification-aisi304. [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :42145201

17 Oct, 2025 NA

Mumbai - Maharashtra

Tender For supply of worm drive hose clamp of size 70 mm. co [worm drive hose clamp of size 70 mm. confirming to is 4762-2002(second revision)and material as per ss-304]

CTN :42105619

29 Oct, 2025 NA

Kolkata - West Bengal

Tender For supply of procurement of set of worm drive hose clamp consisting of 03 items.

Plate Lifting Clamp Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector