Latest plinth work Tenders | Government plinth work Tenders

CTN :45442671

19 Jun, 2026 10.00 Lacs

Palakkad - Kerala

Tender For material supply for works in mgnregs action plan - material supply for mgnregs individual and common asset creation - stone aggregate:40mm nominal size, stone aggregate:20mm nominal size, stone aggregate:10mm nominal size, stone aggregate:06mm nominal size, course sand(zone3), portland cement, concrete mixer, vibrator, stone for masonry work, twisted steel/deformed bars, structural steel such as tees,angles,channels and r.s joists, second class kail wood in planks, second class kail wood in scantling, wall form panel 1250*450mm, corner angle 45*45*5mm 2.5long, column clamp 450*1070mm, prop 2m(2-3.5m), laterate stone of size 40*20*15cm, solid block of size 30*20*15cm, mild steel plates, mild steel rivets, flats up to 10mm in thickness, 20 mm dia.holding down bolts, mild steel sheets for tanks, galvanised wire mesh, iron pintels including welded pin, mild steel sheets with bolts and nuts, mild steel hooks, gi trafford profile sheet 0.35mm thick, galvanised steel jor l hooks 8 mm dia, galvanised steel bolts and nuts 6mm dia and 25mm long round head with slots, wire nails, fine sand, pvc pipe 63 mm outer dia., pvc bend 63 mm dia., pvc pipe 110mm outer dia., pvc elbow 63 mm dia, pvc tee 63*63*63 mm dia, pvc end cap 63 mm dia, pvc reducer 63*50mm dia, pvc pipe 160mm outer dia., gi pipes 50 mm dia., gi pipes 40 mm dia, quarry waste, precoated galvanised plain ridge, vitrified floor tile 60*60cm, welding by electric plant, hire charge of 10hp engine and pump set, diesel oil, 200 mm aluminium aldop, pvc socket/coupling 63 mm dia, polythene water storage tank, red oxide zinc chromate primer, deharadun white lime, smooth wheeled roller 8 to 10 tonne, water tanker 5 to 6 kl capacity, interlocking c.c. paver block (80 mm thick, m-30), sundries

CTN :45416190

11 Jun, 2026 30.00 Lacs

Palakkad - Kerala

Tender For ananganadi grama panchayath ,vendor selection for supply of various mterials for mgnregs - quarry waste, stone aggregate(single size): 40 mm nominal size, stone aggregate(single size):20 mm nominal size, stone aggregate(single size): 10 mm nominal size, stone aggregate(single size): 06 mm nominal size, fine sand (zone iv), coarse sand (zone iii), gravel 5mm to 10mm, stone for masonry work, portland cement, m.s. tube 40 mm dia, mild steel tubes hot finished welded type, galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots, galvanised steel j or l hooks 8 mm dia, g.i limpet washer, bitumen washer, mild steel round bar 12 mm dia and below, mild steel round bar above 12 mm dia, mild steel sheets with bolts and nuts to rest on pintels, iron pintels including weldded pin, mild steel sheets for tanks, mild steel hooks, mild steel plate, mild steel tubes electric resistant or induction butt welded, welding by electric plant, wire nails, bright finished or black enameled mild steel butt hinges 100x58x1.90 mm, bright finished or black enameled mild steel screws 40 mm, bright finished or black enameled mild steel screws 20 mm, powder coated m.s. butt hinges 100 mm x58 mm x 1.9 mm, flats up to 10 mm in thickness, galvanised wire mesh of average width of aperture 1.4 and nominal dia.of wire 0.63 mm, g.i trafford profile sheet 0.35mm thick, precoated aluminium traffored sheet 0.450 mm thick, structural steel such as tees,angles,channels and rs joists, stainless steel screws 50 mm, red oxide zinc chromate primer, precoated galvanised steel plain ridges, stainless steel (grade - 304) hollow section round/square tubes, stainless steel bolts /square bar and plates, g.i pipe 40mm dia, gi plain washer thick, twisted steel/deformed bars, hire charges of concrete mixer 0.25 to 0.40 cum with hopper, vibrator (needle type 40 mm), hire charge of 10 hp engine and pump set - materials, wall form panel 1250x500 mm, corner angle 45x45x5 mm 1.50 m long, 100 mm channel shoulder 2.5 m long, double clip (bridge clip), single clip, wall form panel 1250x450xmm, corner angle 45x45x5 mm 2.50 long, column clamp 450x1070 mm, prop 2 m (2-3.5m), adjustable telescopic prop 3 m (2.02-3.75m), beam clamp 300-380 mm (450-1070 mm), adjustable span eso+si (2.35-3.40), second class kail wood in planks, second class kail wood in scantling, hollock ballies 125 mm diameter, solid blocks of size 30x20x20cm, solid blocks of size 30x20x15cm, hollow blok of size 40x20x10cm, interlocking c.c. paver block (80 mm thick, m-30), pvc vent cowl 63 mm dia, pvc vent cowl 110 mm dia, brass bib-cock-15 mm dia, pvc pipe 63 mm outer dia . 6kgf/cm2, pvc pipe 110 mm outer dia 6kgf/cm2, pvc pipe 25 mm outer dia . 12 kgf/cm2, pvc pipe 32 mm outer dia. 10kgf/cm2, pvc elbow 63 mm dia, pvc 45 degree elbow 63 mm dia, pvc door elbow 63 mm dia, pvc bend 63 mm dia, pvc tee 63x63x63 mm dia, pvc socket/coupling 63 mm dia, pvc elbow 110 mm dia, pvc 45 degree elbow 110 mm dia, pvc door elbow 110 mm dia, pvc bend 110 mm dia, pvc tee 110x110x110mm dia, pvc socket/coupling 110 mm dia, pvc pipe 40 mm outer dia. 10kgf/cm2, pvc pipe 20 mm outer dia 10 kfg/cm2, pvc pipe 63 mm outer dia . 4kgf/cm2, pvc pipe 32 mm outer dia 6kgf/cm2, pvc pipe 40 mm outer dia. 6kgf/cm2, pvc pipe 75 mm outer dia 6kgf/cm2, pvc pipe 110 mm outer dia. 4kgf/cm2, pvc pipe 160 mm outer dia. 4kgf/cm2, pvc elbow 75 mm dia, pvc 45 degree elbow 75 mm dia, pvc socket/coupling 75 mm dia, pvc reducer 63x50 mm dia, pvc vent cowl 75 mm dia, vitreous china orrisa type w.c. pan size 580 mm, brass stop-cock 15 mm dia, flushing cistern p.v.c. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe), 100 mm s.c.i. trap with vent heel, black plastic seat (soild) with lid c.p.brass hinges and rubber buffers, vitreous china pedestal type water closet, stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm, c.i. bracket for wash basin and sinks, polyethylene water storage tank with cove

CTN :45197418

06 Jun, 2026 NA

Panchkula - Haryana

Tender For bid to ras supply of ro plant 1000 lph , installation of 01 tank of 1000 ltr and two tanks of 2000 ltr each , iron stand for storage water tank , iron structure for ro plant , plinth work for ro floor mounted

CTN :45432146

18 Jun, 2026 47.61 Lacs

Gandhinagar - Gujarat

Tender For annual rate contract tender for erection, maintenance and dismantling work of overhead ht/lt line, tc & ht/lt ab cable including mvcc work & plinth work under kalol-1 s/dn, kalol do

CTN :45432150

18 Jun, 2026 47.61 Lacs

Gandhinagar - Gujarat

Tender For annual rate contract tender for erection, maintenance and dismantling work of overhead ht/lt line, tc & ht/lt ab cable including mvcc work & plinth work under chhatral s/dn, kalol do

CTN :45432155

18 Jun, 2026 47.61 Lacs

Gandhinagar - Gujarat

Tender For annual rate contract tender for erection, maintenance and dismantling work of overhead ht/lt line, tc & ht/lt ab cable including mvcc work & plinth work under santej s/dn, kalol do

CTN :45432157

18 Jun, 2026 47.61 Lacs

Gandhinagar - Gujarat

Tender For annual rate contract tender for erection, maintenance and dismantling work of overhead ht/lt line, tc & ht/lt ab cable including mvcc work & plinth work under kalol-2 s/dn, kalol do

Central Government/Public Sector

CTN :45419089

24 Jun, 2026 NA

Cuddapah - Andhra Pradesh

Tender For tender for supply of wall painting with acrylic emulsion paint , providing and applying white cement based putty , 15 mm cement plaster , painting with synthetic enamel paint , 6mm cement plaster of mix , providing and fixing ist quality ceramic glazed wall tiles , white washing with lime , earth work in excavation , providing and laying in position specified grade of reinforced cement concrete , providing and laying in position specified grade of reinforced cement concrete , steel reinforcement , centering and shuttering , structural steel work riveted , demolishing , brick work with common fly ash bricks , half brick masonry with non modular fly ash , providing and fixing white vitreous china pedestal type water closet , providing and fixing wash basin , providing and fixing brass bib cock , providing and fixing water closet squatting pan , providing and laying ceramic glazed floor tiles , providing and fixing on wall face un plasticised rigid pvc swr pipes , providing and placing on terrace polyethylene water storage tank , providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers , providing and fixing pvc door frame , 30 mm thick factory made polyvinyl chloride door shutter , providing and fixing isi marked flush door shutters , neat cement punning , providing and fixing gi pipes , 40 mm dia nominal bore , clearing grass and removal of the rubbish , excavating , supplying and filling of local earth , dismantling colour coated roofing sheet , providing and fixing precoated galvanised iron profile sheets

State Government

CTN :45411968

24 Jun, 2026 35.00 Lacs

Doda - Jammu And Kashmir

Tender For construction of engineering workshop and testing lab including procurement of lab instruments at dam site of bhep. - earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed ordinary rock, 1 meter from cutting edge, providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. all work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. all work upto plinth level with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1 :3 (1 cement : 1 coarse sand : 3 graded stone aggregate 20 mm nominal size), steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level thermo-mechanically treated bars of grade fe-500d or more., filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m., centering and shuttering including strutting, propping etc. and removal of form work., lintel, beams, plinth beams, girders, bressumers and cantilevers., columns, pillars, piers, abutments, posts and struts., structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. welded, providing corrugated g. s. sheet roofing including vertical/curved surface fixed with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i limpet washers or with g.i. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thick with zinc coating not less than 275 gram/m2, providing ridges or hips of width 60cm overall width plain g.s. sheets fixed with polymer coated j. or l hooks, bolts and nuts 8mm dia g.i. limpet and bitumen washers complete. 12.4.3 0.50 mm thick with zinc coating not less than 275 gram/m2, painting on g.s sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on new work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution., brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :cement mortar 1:6 ( 1 cement : 6 coarse sand), extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level, 15mm cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 fine sand), providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete. with galvanized m.s. wire gauge with wire of dia 0.63 mm with 12 mm mild steel u beading, p/f in existing frames 30mm thick factory ma

Central Government/Public Sector

CTN :45384656

13 Jun, 2026 31.96 Lacs

Pune - Maharashtra

Tender For provision of additional transformer alongwith associated items at af stn pune under ge (af)lohegaon - s & f steel tubular swaged poles complete with cast iron plate, finial taper plug, bolt, nuts & screws as specified type 410 sp-55 (11 mtr long) including one coat of red oxide primer and two coats of aluminium paint and making 30 cm wide strips (total -05 nos) with yellow and black paint alternately on external surface above column/pcc benching including numbering with black paint and painting with bitumenous paint internally and externally for portion embedded complete all as specified and directed., s & f air break gang operated switch with 12 nos insulators outdoor type, triple pole, mechanically operated, suitable for vertical installation, single break, provided with locking arrangement consisting of ms chanel ht post type insulator copper alloy, high pressure assembly drop out fuses operating rod of 20 mm dia gi pipe (medium grade) for operating from 1.2 m above gl complete including drop out fuses conforming to is-9921 part-i to v (1982 to 1985) of 1972 rated voltage 11 kv and for current rating 200 amp all as specified, material and labour for lightning arresters nominal discharge current peak 65 ka rating, suitable for operation on ht 11000 volts system, comprising of zinc oxide disks, electrodes, fibre re-in forced composite structure, non tracking weather resistant shedded heat shrinked polymeric housing for withstanding from the effects of pollution, rain, heat and with moisture seal , stainless steel bolts and nuts, stainless steel end fitting cups and fixing arrangements complete all as specified and as directed., m&l for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections i.e m.s. channel or angle sections etc. including new nuts, bolts, washers as reqd dia/length in size, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive one primer coat of red oxide, one under coat and one finishing coat of aluminium paint (1st quality ) as reqd complete as specified., m & l for cement concrete 1:3:6 type c1 (using 20 mm graded aggregate) as lean concrete for coping of pole, stay foundation etc including form work & finishing the surfaces even & smooth with out using extra cement complete all as specified, material and labour for cement concrete 1:2:4, type b-2 (using 40 mm graded stone aggregate) as lean concrete for road finishing even and fair without using extra cement complete all as specified and as directed., supply, laying & testing cable xlpe insulated, screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 11000 volts grade, of size 3 core 95 sq mm., s&f of cable end jointing kit 95 sqmm, 3 core xlpe 11kv ht cable cold shrinkable outdoor type, incl carrying out 5kv megger test after jointing complete all as specified and directed by engr-in-charge., s&f of cable end jointing kit 95 sqmm, 3 core xlpe 11kv ht cable cold shrinkable indoor type, incl carrying out 5kv megger test after jointing ,complete all as specified and directed by engr-in-charge., supply, laying & testing cable xlpe insulated, screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 3.5 core 400 sq mm including aluminium lugs, cable glands ,complete all as specified and directed by engr-in-charge., supply, laying & testing industral pvc frls insulated single core flexible cable, electric power cables (heavy duty) with stranded copper conductor, 1100 volts grade, of size single core 185 sq mm, including copper cable lugs, cable glands ,complete all as specified and directed by engr-in-charge., supply and install, testing and commisioning of outdoor transformer as per is : 1180 part-i, level-ii step down, copper wound 11

Plinth Work Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

Central Government/Public Sector