Tender For procurement of koel da rkit 25 and ard 24 spares - cgsd (mbi), automatic voltage regulator, model avr r450, make leroy somer, service kit for sea water pump - sw23/24/26/28 - long yoyage, i/o module with 8 ai(4.20ma), oil level sensor, set of joints, hp pipe set, pressure transmeter(danfoss make,type mbs 3250,range 0 to 10 bar), 0-2.5 bar danfoss make pressure transmitter for marine, leak off pipe (uniflex), injector, fuel filter cartridge(for dup lex fuel filter), set of copper washers, magnetic pickup sensor, belt for sea water pump drive, water level switch, wire braided pipe from jacketed leak off to fuel, lub oil pressure sensor with switch three point dual wiper type, breather hose for marine, leakoff pipe for hp jacketed pipe (lh), top ring, s.s joint(4), second ring, big end bearing (std), connecting rod bolt, rc joint, valve cup, counter shunk head screw (for dv injector leakoff), s.s.nut, joint (bet.inlet manifold and cyl head), set screw - m8x1.25x25-8.8, plain machined washer-m10, joint (for suction tube flange), nut-m10x1.5-gr.8, stud-m10x1.5x25-8.8, set screw m8x1.25x25...8.8, plain machined washer - m8, set screw - m8x1.25x22-8.8, washer copper, plain machined washer, washer copper for lub oil pipe, washer copper (18x22), copper washer, nozzle body (for oil spray nozzle), sealing cap (40 din 443)8, vent pipe, air shut off valve, exhaust valve, washer copper, stud m10x1.5x35 - 8.8, nut-m10x1.5-gr.8, service kit for centrifugal filter, alternator(2 wire), support for expansion tank, support for expansion tank, support for expansion tank, support for expansion tank, support for expansion tank, plate for thermostat, k sealant (80 ml), joint cooler cover (rh), joint for cooler cover (modified), joint cooler cover (lh), special bolt (233 mm.long) (for integral cooler cover), dome nut for lub oil cooler, special bolt for intergal cooler cover, joint (for thermostat housing), o ring (dia.29) for element oil cooler, set of gasket for heat exchanger, avr, preline filter cartridge, lub oil filter, lub oil pressure switch (4-20 ma), lub oil filter, conical copper washer, valve seal, drain cock, cup for p r tube, rubber bush (top), copper washer, hose clip, wire braided pipe from jacketed leakoff to fuel collector, banjo bolt, coil spring loaded level-edged oil ring piston, inlet valve seat (finish), exhaust valve seat (finish), valve guide (finish), rubber bush (bottom), joint for cac water, breather pipe, make up pipe, fuel pipe (pre-filter to leak off pipe), joint for t connection, leak off pipe (from hp pipe to collector), anti vibration mount - cori, stud, hose clamp, hose t bolt, o-ring for drain plug, 5.6 mm copper washer, o ring for injector, oil filling body o ring, banjo bolt for return line, set bolt-m12x1.75x70-8.8, nut-m12x1.75-gr.8, nut-m14x2-gr 8.8, plain machined washer-m12, plain machined washer-m14, grommet for 12 dia ferrule, grommet for 22 dia ferrule, ferrule(12dia), ferrule 22 dia, grommet support washer 20.2, grommet support washer for dia 31.5, gasket(lub oil header), joint(for flange)for t/c luboil outlet pipe, gasket between oil sump and centrifuge adaptor, dowel bush(for alt. mtg. bracket), alternator pulley, dowel bolt for micro alternator, turbo oil supply pipe(lh), joint between cac &turbo adaptor, sea water outlet pipe from cac, k-cool super plus, ball bearing 6305-2rs1, lub oil filter sub assembly, low water level tank switch, npt plug with zinc bar with he, thermowell for lo temprature sensor, voltage established relay -24v dc, cgsd(chn), fuel filter cartridge, sea water pump, avr (automatic voltage regulator) for cg alternator, pipe lub oil filter header remote, rra assembly for 150 kva alternator, joint for inlet manifold, joint for supply turbo charger, joint for exhaust manifold, r rings, set of joints, k sealant(80 ml), fuel level (leakage) off sensor, oil pipe (lg-675), big end bearing (top std), big end bearing (cap end-bottom std), gpu-3, main bearing(top) std, primary element/air
Tender For supply of multitec mt 02 dx self adjusting wire stripper,taparia 1420 215 mm long nose,wire cutter taparia ws 05 steel 130 mm,taparia 210 mm cutter plier,alis 10 pcs precision esd tweezer set,rc radio master boxer elrs 2 point 4 g 16 channel remote control,soldron temp controlled analog soldering station,quick 857dw plus lead free hot gun,sparkfun electronics 09317 magnifying glass with led light,zip tie,heat shrink wrap,korad dc power supply ka3010d unit,3 point 5 kva ls a 100 portable spot welding machine,rc cellmeter bty,battery stap belt,radio master battery,bty strip nickel strip,skydroid h12 5 point 8 ghz receiver for drone 7 and flight controller,dropping mechanism servo motor
Tender For supply of belt for cutter sa b 46 - cutting plier make taparia , paint aluminium make asian oblique burger oblique shalimar , synthetic enamel paint white make asian oblique burger oblique shalimar , synthetic enamel paint blue make asian oblique burger oblique shalimar , synthetic enamel paint post office red make asian oblique burger oblique shalimar , og paint make asian oblique burger oblique shalimar , paint red oxide make asian oblique burger oblique shalimar , paint smoke grey make asian oblique burger oblique shalimar , turpentine oil make himalayan , french chalk powder , circular saw blade for wood 16 inch dia 25mm bore 80 teeth make extra power oblique bosch , belt for cutter saw b 46 , wooden screw 35 oblique 08 , wall getty 50mm , sanding sheet 60 nos as per sample , sanding sheet 80 nos as per sample , sanding sheet 100 nos as per sample , sanding sheet 120 nos as per sample , sanding sheet 240 nos as per sample , socket set 10mm to 38mm make taparia , sanding machine stand pad as per sample , apron for carpenter , philip oblique multi screw driver 18 inch , 1.5 sqmm pvc copper wire make polycab oblique anchor , electric wire 1.5mm 2 core copper make polycab oblique anchor , plug 3 pin top make anchor oblique polycab , cable copper 9mm make polycab oblique anchor , electric board 3 pin top , casing capping 25mm
Tender For supply of alternator 12v , rubber coupling , fan armature , avr , m seal , lock tie , insulation tape , dc wire 0.75 mm , tape transparent , fevi kwick , needle no 21 , needle no 18 , machine oil , male female clip , anabond , fan belt