Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging
Tender For procurement of spares for dewatering pumps make-maxflow pumps type 50-smp1 installed at fuel oil unloading pump house at unit no. 1 and 2 sgtps mppgcl, birsinghpur - as per schedule, strainer, suction cover, pressure body, impeller (semi - open), impeller nut, impeller key, pump shaft, block, seal plate, oil seal, block bush, top spider, line spider, top spider bush, line spider bush, line shaft, top shaft, pump shaft coupling, bearing sleeve, ratchet plate, grease nipple, pump coupling, ratchet pin, top adjusting nut, coupling rubber, motor coupling, line shaft coupling, gasket, suspension pipe, delivery pipe, .
Tender For supply of pump shaft 40 c8 part no f59751 or equivalent f59751 or equivalent , key pump half coup. part no f59752 or equivalent , oil seal for bearing cover at d.e. part no f59753 or equivalent , hx hd cap screw part no f59754 or equivalent , bearing cover d.e. part no f59755 or equivalent , bearing housing d.e. part no f59757 or equivalent , stuffing box cover d.e. and n.d.e. part no f59759 or equivalent , water seal tube part no f597511 or equivalent , key for impeller 1st stage part no f597514 or equivalent , clinch fitiing part no f597513 or equivalent , impeller 1st stage f597515 or equivalent , wearing ring casing part no f597516 or equivalent , inter stage bush part no f597517 or equivalent , dowel pin int stage bush part no f597518 or equivalent , inter stage sleeve part no f597519 or equivalent , key for impeller 2nd stage part no f597520 or equivalent , impeller 2nd stage part no f597521 or equivalent , shaft sleeve part no f597522 or equivalent , stuffing box bush part no f597523 or equivalent , water seal ring part no f597525 or equivalent , o ring shaft to shaft sleeve part no f597526 or equivalent , split gland assy. part no f597527or equivalent , water thrower part no f597529 or equivalent , oil seal for bearing housing part no f597530 or equivalent , grease nipple bearing housing part no f597531 or equivalent , pipe plug for vib and temp at brg. hsg. part no f597532 or equivalent , bearing housing n.d.e. part no f597533 or equivalent , bearing cover n.d.e. part no f597535 or equivalent , lock nut for brg. part no f597536 or equivalent , lock washer for brg part no f597537 or equivalent , grease relief fitting for brg hsg part no f597538 or equivalent , shaft collar part no f597539 or equivalent , sleeve nut n.d.e. part no f597540 or equivalent , pipe nipple gland drain part no f597541 or equivalent , sleeve nut d.e. part no f597550 or equivalent , spr dowel sleeve part no f597553 or equivalent , pipe plug gauge and air vent part no f597555 or equivalent , eye bolt part no f597556 or equivalent , priming plug part no f597557 or equivalent , clinch fitting part no f597559 or equivalent , fourway adoptor part no f597560 or equivalent , stud bolt nut and washer stfng box cshng part no f597510 or equivalent , stud bolt with nut part no f597528 or equivalent , rotating assembly part no flrauf5975ds or equivalent //bid details 2 / 44
Tender For supply of fuel filter , oil filter , hyd filter , steering filter , jack cyl seal , hyd mtr , track chain seal , his mtr cable , terminal , mud filter , air filter , painting gun with air line , fan belt , bty post lead , feed pump , lifting pump , accelerator cable , break bulb , jcb cabin fan , air filter , service kit mpt , mpt staring ignition switch , heavy duty socket , lashing belt for jcb and mpt , heavy duty knot opener machine , mini socket set , washing pump with motor 3hp single phase , washing pressure pipe , pressure adopter , and bond , hammering paper , m seal , third tape , grease gun adopter , adjustable , grease gun 8 kg , hose pipe 1 and half inch
Tender For supply of washing plant for unit vehicles , hydraulic jack 15 ton , grease gun 5 kg , fuel lifting barrel pump , lifting belt 3 ton , hydraulic lifting truck , ss stand with wheels for tpu and csau