Latest polyethylene liner Tenders | Government polyethylene liner Tenders

State Government

CTN :45007424

26 May, 2026 1.49 Crore

East Nimar - Madhya Pradesh

Tender For corrigendum : complete overhauling of electrical wire rope hoist along with supply of spares for electrical wire rope hoist installed at coal mill area at 2x600 mw, stage-i, sstpp, mppgcl, dongalia. - scope of service, complete supervision & installation of new spares/replacement of damaged/eroded spares of all 08 numbers of hoist (04 numbers capacity-20 ton & 4 numbers of capacity-15ton)., scope of supply, spares for 20 ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4 duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct<, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 20, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 20 mm / 6x36 steel core/ galvanized, make- ushamartin, push buttons with 12 meter cable, rectifier size- eh720hhd, long travel dsl system, i- chain (5 mm)-, ii- cable 6 mm epr, iii- fasteners (1/4x2 ), lt motor shaft, lt motor pinion, spares list of 15-ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4,duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 18, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 15 mm / 6x36 steel core/ galvanized, make- ushamartin, pendent push buttons, rectifier size- eh720hhd, long travel dsl system, chain (5 mm)-, cable 6 mm epr, fasteners (1/4x2 ), lt motor shaft, lt motor pinion

CTN :45291537

05 Jun, 2026 2.99 Lacs

Darjeeling - West Bengal

Tender For tender for supply of repair maintenance and servicing of eot crane 2 ton - servicing and maintenance of cranes 02 ton an all allied works with load test. , bridge & cross traverse rail alignment by clamps fitting/ adjustment , replace repaire dsl or ip supply cable on long travel , replace current collector for smooth operation , hoisting motor 5.2kw , 3ph , sc servecing only , cross traverse motor 0.55kw , 3ph , sc servecing only , long travel motor 2.2kw , 3ph , sc servecing only , bridge wheel assembly maintenance and replacement of defective part any of wheel , bearing , spacer , shaft , coupling , brake , gearbox , trolley crab wheel assembly maintenance and replacement of defective part any of wheel , bearing , spacer , shaft , coupling , brake , gearbox , hoock block maintainance and replacement of defective part any of pullies , rope lock , pulley bearing , thurster bearing , cover fastners , replacement of hoist wire rope dia 12 6 nos 36 fibre core , hoist assembly maintenance and replacement of defective part any of coupling , brake shoes , bearing , spacer , shaft , gear. , equiliser pulley maintenance and replacement of defective part any of pulley , shaft , bearing , maintainance for span of the crane within limit , it must not wear wheels on either sides of flanges , maintainance for diagonals of crane within the limit , it must not wear flanges of lt wheels or must not get jam of lt motion , rubber buffers replacement , limit switch for any of motion long travel cross traverse hoisting ) , relay maintenance or replacement with accessories , cross traverse cable replacement , cross traverse cable trollies maintenance or replacement

CTN :45085629

01 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For corrigendum : supply of hoist brake for sul

Central Government/Public Sector

CTN :45111404

26 May, 2026 NA

Medak-T - Telangana

Tender For corrigendum : k6a1z68773-el.op.mll hand.system 8 mills -hp1103 - el.op.mll hand.system 8 mills -hp1103, set of axle bearings for long travel, gearbox bearings with sleeves for lt, long travel end shaft bearings, seals for long travel gear box, long travel brake shoes lining, axle bearings for cross travel, gearbox bearings with sleeves for ct, cross travel end shaft bearing, set of seals for gearbox for ct, cross travel brake shoes lining, main hoist pulley bearings, bearings for gear box for hoist, set of seals for main hoist, main hoist brake shoes, main hoist brake springs, main hoist brake shoe liners, 415 v motor bearings for each type, 415 v motor cooling fan ea type, 415 v motor terminal blocks for each ty, supervision of e&c at project site

State Government

CTN :45287266

04 Jun, 2026 NA

Chandrapur - Maharashtra

Tender For supply, installation, testing and commissioning of vfd, main-auxiliary hoist dbr & dc brake assembly for eot crane of capacity 100/15 ton installed at tg floor of 3x500mw, cstps chandrapur during coh of unit#7.

Central Government/Public Sector

CTN :45264914

30 May, 2026 NA

Bhopal - Madhya Pradesh

Tender For supply of 2.2 kw ac crane drive , 5.5 kw ac crane drive , 11.0 kw ac crane drive , 22.0 kw ac crane drive , 37.0 kw ac crane drive , 55.0 kw ac crane drive , 75.0 kw ac crane drive 3 phase, digital ac crane drive 2.2 kw, ac drive should be suitable for heavy duty operation of 2.2 kw. offered ac drive should be suitable for crane-hoist operation. if, separate software required for crane application, it must be clubbed with supply of material. ac input voltage: 380 to 480v ac 10%, 3 phase, 3 wire, 50 hz; mode of control: bi-directional fully controlled 3-phase ac; speed regulation: 1% of base speed; braking: suitable dynamic braking resistance and chopper unit (external or in-built); acceleration time: 0.1 to 1000s or better; deacceleration time: 0.1 to 1000s or better; overload: 150%-1min, 200%-3.0s; ambient temperature: 0 to 50 c (derating shall not occur below 50 c. in the event that derating occurs below 50 c, the supplier shall provide a higher-rated drive to match the requirement); rated current at 50 c: min. current should be 5.5 amps at 50 c; high starting torque at low speed: 200% starting torque at 0.3 hz; two analog inputs: two nos. analog inputs having signal voltages of 0 to 10 vdc or 4 to 20 ma (configurable); two analog outputs: two nos. analog outputs having signal voltages of 0 to +/-10 vdc or 4 to 20 ma (configurable); six digital inputs: pnp/npn; one relay output: with short-circuit and overload protection; two digital outputs: with short- circuit and overload protection; brake release signals: outputs braking signals based on inverter operating conditions to prevent cargo bed rollback and overrunning; load adaptive control: when the actual load level is lower than the configured load level, the system can be operated at a ratio-multiplied speed (in terms of the configured frequency), resulting in significantly better efficiency; load ) /bid number : gem/2026/b/7563714 * /dated: 20-05-2026 & & / bid document 1 / 29 frequency), resulting in significantly better efficiency; load limiter: maintains the safety and rescuability of suspended loads by stopping when excessive torque is detected and by allowing operation only in the direction opposite to that in which the excessive load was detected; cooling capacity degradation alarm: detects and displays cooling capacity drop due to cooling fin clogging caused by dust and cooling fan airflow reduction; igbt life expectancy forecasting: estimates the power cycle life expectancy of the main circuit s igbt semiconductor device temperature due to frequent acceleration and deceleration stoppages, and displays the estimate before the design life is reached; protection: it must have all standard protections like stall protection, instantaneous power failure, single phasing, over voltage, under voltage, over current, inverter overload, thermal overload etc; display console: it must have alpha numeric display console for programming of drive, fault display and operating condition; dynamic qr code: it must have dynamic qr code for trouble shooting; tuning facility: it must have auto tuning facility. this must enable perfect matching of motor coupled to load with regards to optimum acceleration time, deceleration time, speed regulation etc; drive programming software: suitable drive programming software along with necessary connecting cable and adapter for connection with laptop and drive should be provided to get online with the offered drive (laptop not in scope); automatic voltage regulation: it must have automatic voltage regulation function to maintain high starting torque even at reduced voltage; regenerative option: it must be capable of regenerative operation; communication protocol: modbus (rtu/serial) or ethernet (tcp/ip); make of drives: fuji- electric/yasakawa/schneider/abb only; suitable dynamic breaking resistance unit of 60% wattage rating of drive, however the value of resistance is to be decided by manufacturer as per their technical manual for crane-ho

Central Government And Public Sector

CTN :45252368

29 May, 2026 NA

Damanjodi - Odisha

Tender For supply of 1 . 71099046000 rear suspension cylinder seal kit part no-081805318 , 2 . 71099046170 front suspension repair kit pt.no.81805317 , 3 . 71099003410 repair kit pt.no. 81805315 , 4 . 71099039950 relay valve 81403325 , 5 . 71099059300 pto assly 81029246 for cat ws 1035 , 6 . 71015008480 hyd. break pump part no.81028771pump brake coolingpt.no.81028771 , 7 . 71099037260 hose assy 81025370 applicable for hm1035ws water sprinkler , 8 . 71099047740 coupling 81023675 , 9 . 71015051040 hose assembly pt. no. - 81022623 for cat water sprinkler model ws1035 , 10 . 71099037400 81021491 hose assy applicable for 1035 water sprinkler , 11 . 71050014460 hoist cable pt.no. 81017516 , 12 . 71015000620 hose pt.no.81015361 applicable for hm1035ws water sprinkler , 13 . 71099041430 hose pt.no.81011401 for water sprinkler model hm1035ws , 14 . 71015915760 hose assy. 081009401 , 15 . 71099024510 hoist cable part no. 81006056 , 16 . 71099039400 condensing drain valve 81005304 , 17 . 71099041740 horn solenoid 81004027 , 18 . 71015002550 hose pt.no-9194159

corporations/Associations/Others

CTN :44949160

25 May, 2026 6.32 Lacs

Kasimpur - Uttar Pradesh

Tender For corrigendum : tender for supply of mukand eot crane spares - mukund make eht brake 200 dia 18 cross travel , mukund make eht brake 200 dia 18 long travel , eht breake 400 dia 46 axis hoist oem mukand , pendent push button station oem mukand , mukund make rrc for eot crane , rg limit switch ratiooem mukand , master controller mh oem mukand , mukund make master controller ah for eot crane , master controller ct oem mukand , mukund make master controller lt for eot crane , eht breake 300 dia 34main hoist oem mukand

corporations/Associations/Others

CTN :45197456

04 Jun, 2026 5.77 Lacs

Jhansi - Uttar Pradesh

Tender For supply of 1723 brg of drum section model de-4sh-sp , 1723 coupling assembly model de-4sh-sp , 1723 driving wheel asly model de-4sh-sp , 1723 hoist brake model type-de-4sh-sp , 1723 brake disc assembly model de-4sh-sp , 1723 drum rope assembly model de-4sh-sp , 1723 main drum asly andbrg model de- 4sh-sp , 1723 hoist gearbox and brg model de-4sh-sp

Central Government And Public Sector

CTN :45167110

02 Jun, 2026 NA

Bangalore - Karnataka

Tender For wire rope hoist of 2t capacity confirming to is-807,3938 with hoist carrier for ct movement to suit 150 mm rail width as per the following specification. equipment : electric wire rope hoist; capacity : 2000 kgs ; duty & class : class iv heavy duty; height of lift : 5.0 mtrs; rail size : 150 mm width, 450 mm height ; hoist head room : 900 mm ; hoist speed : 3 mpm; ct speed : 12 mpm; hoist motor : squirrel cage induction motor 5 hp with brake , tefc sq. cage induction motor 3.7kw / 5hp , 4 pole , class f insulation , 415v , 3 ph , flange mounted , frame size 112m with dc operated electromagnetic brake of minimum braking capacity of 5 kgm, continously rated; ct motor and brake specifications :squirrel cage induction motor power : 0.37 kw , pole : 4, efficiency : ie3 , frame : 71m , mounting : b5 flange , brake : electromagnetic disc type spring loaded ac fail safe brake of min torque : 0.6kg.m; voltage : 415v , phase : 3 phase , compressed spring length : 40 mm , air gap : 0.5 mm; hoist & ct gearbox : helical / spur gear combination. all gears inside the gearbox shall be of en-24 material with hardness of 40-45 hrc. mtc and htc from nabl accredited lab should accompany the supply. wire rope : round strand steel wire rope conforming to is 2266 latest and is 6594 latest size : 10mm or 12mm , 4/1 falls construction : 6 x 36 . drum : seamless pipe of suitable dia & shell thickness to accommodate wire rope single layer as per is-2062; hook : forged heavy duty single shank typeplain hook as per is-3815, 360 swivel type with spring loaded safety latch. control panel :consists of mcb, olar, fuse, etc. note: (a) test certificate for hook shall accompany the supply (b) make of bearings: skf/ntn/fag/timken only. (c)the firm shall furnish inspection certificate from manufacturers or their authorised testing agents preferably incorporating the details of traceability of the bearing. (d) all gears inside the gearbox shall be of en-24 material with hardness of 40-45 hrc. mtc and htc from nabl accredited lab should accompany the supply (e) make of motors: ngef / abb / lhp / cg / hem /bharat bijlee only; (f) make of electricals: siemens/ge/alstom/l & t/abb only ;control voltage: 110v ;supply voltage: 400/440v, 3 phase 50 cycles. (g) guarantee: 12 months from the date of commissioning or 18 months from the date of supply, whichever is earlier. [ warranty period: 18 months after the date of delivery ]

Polyethylene Liner Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors