Tender For supplying, installation, testing and commissioning of machines and equipment for civil engineering department at ttaadc polytechnic institute, khumulwng, west tripura for the project improvement of infrastructure in ttaadc polytechnic institute, kh - supplying, installation, testing and commissioning of machines & equipment in civil engineering department at ttaadc polytechnic institute, khumulwng, west tripura under the nec scheme "improvement of infrastructure in ttaadc polytechnic institute, khumulwng, west tripura, district under higher education departmen.", computerized universal testing machine, 6 pillar type, for conducting tests on various types of ferrous and non-ferrous materials; consisting of-loading unit 600 kn capacity, hydraulic jaws and pumping system, clamping jaws for round specimens, clamping jaws for flat specimens, pair of compression plates,for compression test, rollers of 160 mm width and 30 mm diameters, for transverse test, bending table stopper, allen keys, spanners,double shear test attachment, bend rebend test attachment, electronic extensometer., steel bar cutting machine, vernier caliper, stainless steel ruler, 1m length, mixer machineriesconcrete mixerthe counter balanced mixing drum is easy to tilt two cubic feet mix capacity. total drum volume is 3 cubic feet.. suitable for operation on 220 volt single phase, 50 cycle, a.c. supply, isi cube mouldcube mould, with base plate : as per is : 516 with isi mark cube mould, 15 cm x 15 cm with base plate (made of cast iron - isi mark), cement mortar cube mouldcement mortar cube mould cube mould, 7.06cm x 7.06cm with base plate (made of mild steel), vibrating machinevibration machine with timer : is : 4031 this apparatus is suitable for making cubes of 70.7 mm. for mortar strength evaluation. the mould is mounted on a vibrating platform with a frequency of 12,000 400 vibrations per minute. to the platform are attached four matched springs. the whole assembly is operated by a revolving shaft with an eccentric mechanism. the machine is supplied with a timer, a switch mounted on a steel panel and a 70.7 mm. steel cube mould with a base plate., electronic balancecapacity 500gm, 0.01 gm accuracy, electronic balancecapacity 5kg, 0.1 gm accuracy, electronic balancecapacity 20kg, 0.5 gm accuracy, electronic balancecapacity 100 kg, 10g accuracy, air permeability apparatus (blaine type)isi certification mark is;5516, fitted in aluminium box, vibrating tablevibrating table for compaction concrete cube, cylinders the table deck size 50 cm x 50 cm and has stops along its edges to prevent moulds from walking off the table during vibration the variably pitch pulley arrangement permits the frequency to be varied sleeplessly between a maximum of 3600 vibrations per minute a speed regulation handle is provided for increasing or decreasing the frequency. the vibrating deck. a switch is provided for starting the motor. operation on 440 volts, three phases, a.c. supply. table top - 50 cm x 50 cm, curing tankwater curing bath with agitation system digital indicator for temperature * 24- hour cycle from time of mixing * controlled 100 c +/- 2 c. temp. for concrete * controlled 27 c + 2 c curing temperature for grey cement the tank has been designed to accommodate 150 mm / 70.6 mm casted cubes up to 12/24 cubes and fully insulated. complete with a hinged lid, heated, thermostat and recirculation pump. provision of two removable racks allowing free circulation of water around each cube. the pump, drain valves and electrical equipment are housed in a compartment located at one end of the tanks. the tank is heated by an immersion heater under normal conditions and refrigeration system for grey cement, the temperature is controlled at 35deg.c. +/- 2 deg.c, for about 15 minutes after immersion of the freshly-made specimens. curing tank for 12 moulds of 150mm/24 moulds of 7.06mm, vicat apparatus boxwith isi certification mark, is:5513, fitted in aluminium, le-chatelier mouldwith
Tender For supply of manpower - 22 nos., of semi-skilled workers as counter operators to work under the control of o/o aeo(vqc), tirumala to utilize their services at vqc-i&ii, ttd, tirumala / ssd counters, tirupati as assigned by the department from time to time
Tender For supply of fret-real time pcr (bio molecular analytics system) along with accessories - fret-real time pcr (bio molecular analytics system) along with accessories along with the accessories with three years warranty, automated cell counter with three years warranty, semidry rapid western transfer system, optional: reverse transcription supermix; 100x 20 l rxns 400 l; 4 x100 l of 5x supermix, containing reverse transcriptase; rnase inhibitor, dntps, primers, mgcl2, stabilizers; 50 reactions of no-rt control supermix, optional: high-fidelity dna polymerase, 100 u (2u/ l), 50 l,(stand-alone enzyme) that includes 5x reaction buffers, mgcl2 solution, dmso, optional: horizontal gel electrophoresis system for dna and rna, 7 x10 cm tray, with mini-gel caster, mini horizontal electrophoresis system that includes 8- and 15-well combs, 7 x 10 cm (w x l), uv-transparent tray, mini-gel caster, optional: rna isolation reagent 100 ml, reagent for dna-and protein-free rna isolation, optional: plasmid miniprep kit 100 preps; plasmid dna purification kit that includes spin columns and plasmid dna isolation solutions (cell resuspension and lysis, neutralization, wash), optional: molecular biology grade agarose: 125g general purpose agarose for nucleic acid electrophoresis which is certified free of inhibitors, dnases, rnases, optional: 1 year amc post warranty period