Tender For supply of ahu bearing with tapper block and slive uk 205 , condenser pressurereliefvalve 450psi , expansion valve hse12c , vibration eliminator 1 18 inch , vibration eliminator 7 8
Tender For supply of 1-1/2" inch lpg control valve without actuator , 3/4" inch pilot lpg regulator inlet pressure 7 psi max outlet pressure range 18 to 40 mbar , 1/2" inch pressure balance ratio regulator for lpg service , uv sensor for lpg burner flame detection , dn40 main gas regulator for lpg service 5 bar max inlet pressure outlet pressure range 85-180 mbar , ignition electrode for heater , pilot burner without ignition rod , 1-1/2 inch solenoid valve normally closed auto reset fofc with cpi switch for lpg service 240 volts , dn25 pressurereliefvalve for lpg service
Tender For supply installation testing and commissioning of pump unit and other electro-mechanical equipments at laripora pahalgam - supply, installation, testing and commissioning of submersible type pump sets with motors and allied mechanical and electrical components/ items as per manufacturer s recommendations and guide lines, and as per the scope of the work at site. the equipment supplied conform to latest is- standards and codes with fail safe circuits/ devices for(i) over loading (ii) under loading (iii) clogging (iv) shut off (v) low liquid level (vi) single phase prevention devices (vii) over heating etc. the pumping units shall have following technical specifications: pumps:type of pump :non clog centrifugal volute type sewage submersiblepumpscapacity= 28.4lpshead = 17.5 metres or abovesolid handling capacity: 20mm (minimum) quality of water: sewage water to be handled meterial of construction:pump casing : cast ironimpeller : stainless steelpump shaft : stainless steelmotor body : cast ironsealing : dual mech. seal...contd.. as per annexure-a, providing/supplying and fitting of 100 mm m.s flanged delivery main to be connected with existing rising main at site. the job includes providing and welding of m.s flanges 12 mm thickness. the flanges shall be double welded both from inside and outside of the pipe using standard electrode of reputed make. the cost on account of supply/ fabrication of bends and providing/ fitting of flanges is included in the job. (complete job)., providing and fitting of 100 mm dia ductile iron double flanged, non-rising spindle soft seated glandless gate/ sluice valves as per is14846 for regulating the water supply outside the pumping units p.n rating 1.0.the job includes providing and fitting of 02 nos. m.s flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with rising main of the pumping unit at appropriate spots as per site requirement (complete job)., providing and fitting of 100 mm dia ductile iron double flanged, slanted seat swing check valve( nrv) as per is 5312 p.n rating 1.0.the job includes providing and fitting of 02 nos. m.s flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with rising main of the pumping unit at appropriate spots as per site requirement (complete job)., gantry over sump :- fabrication, providing, fitting of ms gantry over sump with 02 nos. vertical columns. the gantry fabricated out of ismb-100, 3.25 mts long placed face to face. 300x300mm ms plates 12mm thick fitted on top and bottom side of column .bottom plate welded to the reinforcement of the sump and grouted in 1mx1mx1m pcc 1:1.5:3 mix. ismb-100,3mts long is to be placed and welded to the top plate of the columns .the job also includes providing and fitting of 2-tonne capacity chain pulley block with monorail along with hoisting chain (complete job)., providing and fitting of 50 mm23.5 core ,al pvc insulated cable, armouredfor internal connectionscrimping, taping etc. note:- the cable terminal ends for connection to switchgear at various requisite points shall be al. thimbles and of appropriate size and connected by hydraulic crimp tool only (complete job)., providing and fitting of 4-core 16 mm2 flat /circular submersible copper cable conforming to is: 694 (part 1st) 1964 & is: 694 (part 2nd) - 1964 for submersible pumping unit and other electrical equipment s. the cable connections terminal shall be fitted with copper thimbles of required size (complete job)., fabrication, providing and fitting of main electric control panel of appropriate size fabricated out of 14 swg sheet having required openings/vents and protection class : ip-55 & fitted with accessories as under: a) bus bar chamber: 160 amperes(tpn) b) main circuit breaker (incomer mccb) qty:- = 01 nocurrent rating = 160 amp. c) change over switch:qty. = 01 no.rating = 160 ampere....contd... as per annexure-a., electrification. providing/fitting of lighting and fan points (06) in
Tender For auction sale of depot ferrous scrap - 98080106: cond. & u/s. signal items and ms/ci/gi item scrap consisting of point machine, ground connection, , point machine base, lock rod,contactor unit parts, other point machine parts, loco parts, gears, slide cover, cams, ms rotors, beaters, bars, ms rod/angle /channel/pipe cut piece, bm box, pipe fittings, screw couplings, coupling hook, signal three aspects, signal two aspects, cast iron components, pressure tank, augers, dip lorry, ms trolly, tension rod, plate, large pipe,signal post, fastners, pick axe, beaters, crow bars, lever, train coach door broken parts, ms stand, weighing set, traction motor case, compressor case, compressor valve, ms tank, nut, bolt, tool box, ci linked pots, chain, damper, l c gate parts and tap, valve, gear case, flat rod, ms trolley, rottery key, grill, pulley, air filter,cut of angle cock,knuckle pin,wearing plate,cp bottom,ci part, fencing, hood, boiler tube, winch wheel, lc gate parts, steel rope, ladder, battery boxes, frames, ms boxes, ring, ci foundation ct boxes, loco liner, buffer, buffer case, buffer plunger,icf buffer complete set, piston, piston cylinder,weigh machine, connecting rod, signal posts with or without base, bearing case, tension rod, cam shaft,ms cut pieces,pipes, storng part with diabar ms attachment,pure iron flats,pump case, pta parts,shock absorber,e type lock,d bracket,axle box housing,end shield,cast iron component, trolly parts, hyd scissors table,air suspension system, pipe,ladder, pantograph parts, sack barrow,winch for lb gate,l angle,gate boom,rail wheel barrow,nozzle pricker, ms hood tap and such other similar signal,cut pieces of mast, loco and c&w items with or without non ferrous and other attachments as is where is condition. note: (1) if any non- ferrous items found in loose in the location to be handed over to custodian at the time of delivery, (2) crane/jcb loading permitted (3) cutting permitted to loadable size at the time of delivery (4) electronic weighbridge capacity 30 mts only. hence purchaser should bring suitable vehicle so that the loaded weight should not exceed 28 mts at the time of delivery. locotion: w-6& 7 of scrap yard/ssd/ptj.
Tender For high pressure jet cleaning machine working pressure: 200-250 bar water flow rate: 900-1100 liters/hour steam temperature (if applicable): 140-155 degree celsius hot water output temperature: 85-90 degree celsius suction height (from water source): minimum 0.5 m pump specifications critical for durability and pressure stability. pump type: triplex plunger pump pump speed: around 1450 rpm number of pistons: 3 piston material: ceramic minimum feed pressure: 6-8 bar motor & electrical specificationsdefines power and efficiency. power supply: electrical phase: single phase / three phase motor rating: around 7-7.5 kw protection class: ipx5 or higher automatic pressure cut-off: yes heating system (for hot water models) optional but essential for grease removal. burner type: diesel / electric burner power: 60-90 kwfuel tank capacity: around 20 liters detergent tank capacity: around 20 liters hose, gun & lance user interaction components. high-pressure hose length: 8-10 meters electrical cable length: 5 meters spray lance length: approx. 700 mm spray gun: standard high-pressure trigger gun quick-connect couplings: preferred construction & materials ensures robustness and long service life. chassis material: mild steel (industrial grade) body material: mild steel or corrosion-resistant metal wheels: solid rubber wheels frame design: compact, vibration-resistant safety & protection features mandatory for industrial equipment. thermal motor protection pressurereliefvalve overload protection weather-proof switches low-water cut-off (recommended) dimensions & weight affects portability and storage. weight (without accessories): 140?150 kg mobility: trolley-mounted with heavy-duty wheels accessories (standard supply) high-pressure hose spray gunspray lance nozzle set detergent suction hose operating conditions operating temperature range: 0 degree celsius to 40 degree celsius environment: dusty, humid, industrial conditions [ warranty period: 30 months after the date of delivery ] ]