Tender For purchase of renewable energy practical equipments - equipments for renewable energy practices:, rc phase shift oscillator oscillator type: rc phase shift oscillator using transistor / op-amp configuration. input supply: 230 v / 50 hz ac with regulated internal dc supply. output frequency range: 100 hz 10 khz adjustable. output: sinusoidal waveform with adjustable amplitude up to 10 vpp. rc network: three-stage rc phase shift network with frequency control arrangement. cro test points: dedicated cro terminals at amplifier output, each rc stage, and final output for waveform and phase-shift observation. protection: over-voltage and short-circuit protection provided. indicators and controls: power on led indication with frequency and gain adjustment controls. accessories: patch cords, circuit diagram, strain guage characteristics kitac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords, load cell characteristics kit input supply: 230 v / 50 hz ac with regulated internal dc supply. sensor: strain gauge load cell with suitable mounting arrangement. load range: 0 10 kg. display: digital display for load/output indication. cro / test points: test points provided for observing bridge output, amplifier output, and signal conditioning stages. controls: zero adjustment and calibration controls provided. protection: overload and short-circuit protection provided. accessories: loading arrangement, connecting leads., measurement of tank level using rotometer input supply: 230 v / 50 hz ac with regulated internal dc supply. tank arrangement: transparent tank with 30 liters capacity with suitable supporting stand. rotameter range: 0 4000 l/hr calibrated rotameter. flow system: pump, control valves, and piping arrangement provided for continuous flow operation. measurement facility: provision for flow-based tank level measurement and observation. display / observation: calibrated level indication with flow monitoring arrangement. test points: output terminals provided for monitoring sensor/output signals. accessories: connecting tubes., measurement of tank level using displacer type level transmitter input supply: 230 v / 50 hz ac with regulated internal dc supply unit. measurement principle: buoyancy (archimedes principle) using displacer element. tank arrangement: transparent experimental tank with 30 liters capacity and suitable mounting stand. level range: suitable laboratory-scale level measurement (0 100% tank height). sensor system: displacer type level transmitter with continuous level output signal. display unit: digital indicator for level display in percentage / engineering units. output signals: standard analog output (4 20) ma / (0 10) v provided for monitoring. test points: provided for transmitter output, signal conditioning, and display unit verification. controls: zero and span calibration adjustment provided for setting level reference. protection: over-voltage and short-circuit protection for electronic modules. accessories: connecting cables, piping arrangement, loading medium (water), measurement of temperature using pt100 input supply: 230 v / 50 hz ac with regulated internal dc power supply unit. sensor: pt100 resistance temperature detector (rtd) probe with stainless steel sheath. measurement principle: resistance variation of platinum element with temperature. temperature range: 0 c to 150 c (or suitable laboratory range). display unit: digital temperature indicator with direct c display. accuracy: high accuracy with linearized rtd signal conditioning circuit. sign
Tender For purchase of lab equipments for res dept - purchase of lab equipments for res dept, rc phase shift oscillator (iemcode:o001)specifications: oscillator type: rc phase shift oscillator using transistor / op-amp configuration. input supply: 230 v / 50 hz ac with regulated internal dc supply. output frequency range: 100 hz 10 khz adjustable. output: sinusoidal waveform with adjustable amplitude up to 10 vpp. rc network: three-stage rc phase shift network with frequency control arrangement. cro test points: dedicated cro terminals at amplifier output, each rc stage, and final output for waveform and phase-shift observation. protection: over-voltage and short-circuit protection provided. indicators and controls: power on led indication with frequency and gain adjustment controls. accessories: patch cords, circuit diagram., strain guage characteristi cs kit(iemcode:o002)specifications: ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. no rs.10,000 2 table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords, load cell characteristi cs kit(item code: o003)specifications:input supply: 230 v / 50 hz ac with regulated internal dc supply. sensor: strain gauge load cell with suitable mounting arrangement. load range: 0 10 kg. display: digital display for load/output indication. cro / test points: test points provided for observing bridge output, amplifier output, and signal conditioning stages. controls: zero adjustment and calibration controls provided. protection: overload and short-circuit protection provided. accessories: loading arrangement, connecting leads., measurement of tank level using rotometer(item code: o004)specifications: input supply: 230 v / 50 hz ac withregulated internal dc supply. tank arrangement: transparent tank with 30 liters capacity with suitable supporting stand. rotameter range: 0 4000 l/hr calibrated rotameter. flow system: pump, control valves, and piping arrangement provided for continuous flow operation measurement facility: provision for flow-based tank level measurement and observation. display / observation: calibrated level indication with flow monitoring arrangement. test points: output terminals provided for monitoring sensor/output signals. accessories: connecting tubes., measurement of tank level using displacer type level transmitter(item code: o005)specifications: input supply: 230 v / 50 hz acwith regulated internal dcsupply unit. measurement principle:buoyancy(archimedesprinciple) using displacerelement tank arrangement: transparent experimental tank with 30 liters capacity and suitable mounting stand. level range: suitable laboratory-scale level measurement (0 100% tank height). sensor system: displacer type level transmitter with continuous level output signal. display unit: digital indicator for level display in percentage / engineering units. output signals: standard analog output (4 20) ma / (0 10) v provided for monitoring. test points: provided for transmitter output, signal conditioning, and display unit verification. controls: zero and span calibration adjustment provided for setting level reference. protection: over-voltage and short-circuit protection for electronic modules. accessories: connecting cables, piping arrangement, loading medium (water), measurement oftemperature using pt100(item code: o006a)specifications: input supply: 230 v / 50 hz ac with regulated internal dc power supply unit. sensor: pt100 resistance temperature detector (rtd) probe with stainless steel sheath measurement principle: resistance variation of platinum element with temperature. temperature range: 0 c to
Tender For corrigendum : tender for supply of bulb 24v 40w b15 , bulb 40w , glass globe joint , o ring joint , bulb 115 60w b22 , bulb 24 v 40 w b15 , bulb 24 v 40 w b15 , bulb quartz iode 120v 250w , optical class , optical glass joint , pressure switch sensing element for fplm34dtxnsn , pressure switch sensing element for fplm34dkxsn , pressure switch sensing element for fpm34dqxnsn , temperature switch sensing elements for fcm34dgnsn , temperature sensor type pt 100b with ss316ti heath , configurable electronic module with pcb for emi protections , programmable temperature detector with 110mm probe length , temperature sensor assembly without electotronic module lm 176 , temperature sensor assembly without electotronic module lm 196 , flowrate signal processing unit amesys internation , typr 14p limit switch with a 20 m cable , 24 v aquacel type l37 reserve battery , pressure transmitter 0 15 bar absolute g 1 4 female , proximity detector neb 12 18mg50 e2 , remote thermometer 100mm type form 0 to 100 deg g full , thermometer 0100mm type a 0 to 100 degree c fcapillary k 2 m , manual call point , smoke detector , input module , limit switch contact , 1 0 m maximum height fresh water tank 1 level gauge , absolute pressure switch , conduct electrode h20 detect device al threaded coupling , differential pressure switch sensing element , electronic for fmb52 , electronic insert fel54 relays dpdt , level transmitter fmb52 , level transmitter fmb52 , position detector end valve fresh air pipe cm e 14 g21 3 , posn detector end vv air pipe cm e 14 g21 3 , pressure switch sensing element , pressure switch sensing element , pressure switch sensing element , pressure switch sensing element , pressure swith sensing element , pressure 60l alimentary quality balloon horiz or vert , dc dc converter , relay 2rt10a 28vcc , relay 4rt10a 28vcc , relay tpr2 28vcc , relay 6rt10a 28vcc , relay 6rt10a 28vcc , fuse series psc type 6 6 urd 30 tt f 0200 , cartridge fuse ha22 type 6 3 32 6 3 a , cartridge fuse ha22 type 6 3 32 1 6 a , monostable relay 10a 28vdc type 4 i 10 b1 p 28 , berard acturator oa8 115b 60 hz 3ph marline ral7038 , 115v 24 vdc converter , relay2rt 10a 28vdc suppressed device saphir code rel005appar , relay4 rt 2a 28vdc dc p
Tender For qualifying requirement for vendor enlistment for supply of pressure transmitter(electronic transmitter for pressure, diff press and dp based flow / level measurements)
Tender For supply of import substitution of items by indigenous development - crome casing pipes, chrome tubing pipes, drill pipes, heavy weight drill pipe, drill collars and lifting plug, drilling stabilizers, drilling/ workover handling tools --- elevators, tongs,, slips etc., potassium formate, solid control equipment --- mud cleaner/ degasser/, centrifuge/ linear motion shale shaker, sucker rod pump (srp) and its accessories:, tubing conveyed sucker rod downhole pump, rod conveyed sucker rod downhole pump, downhole gas separator, downhole anchor catcher, srp fishing tools:, overshot, spares for overshot (grapple, control, guide etc.), srp insert pump, ethyl mercaptan, low shear velocity fluids/polymers, emd chemical dosing pump, reciprocating pump, hsp 20/40, isp 20/40, isp 30/50 mesh, pig tracker/transmitter, pipeline locator, logging cables, tri cone roller drilling bits of various sizes, 11"od standard reverse circulating junk basket & 7.7/8" od reverse, circulating junk basket, pdc drill bits of various sizes, fishing tool; 6.5/8 inches od junk sub for operation inside 8.1/2 inches hole, impression block for 4.5 inch od, 5.0 inch od, 9.625 inch od & 13.375 inch od, casing, pneumatic spinner, 5.1/ 2" premium threaded casing (grade: n80 & grade p110), cased hole logging units with tools and accessories along with, installation, commissioning and training, wireline mast unit, including training and installation& commissioning, oil well explosives: (i) 2-1/8 inch tubing cutter along with detonator and, hardware accessories, (ii) 1-9/16 inch tubing puncher/ circulation charge & hardware accessories, oil well explosives: explosives for baker pressure setting tools: power, charge, primary ignitor & secondary ignitor, procurement of oil well explosives used in exploration and production of, hydrocarbon, (i) deep penetration charges, (ii) resistoriess detonator assy,, (iii) deto cord 80 hmx nylon ls 1.4s, (iv) 54 mm strip carrier, 6spf, 12 ft/3 m long, (v) detocord /charge clips, (vi) tandem connector ,2.1/8" stri p carries, (vii) splice boot for lead wire, (viii) detonator cord retainer, (ix) 53.975 mm (2.1/8") od firing head assy, (x) nut & bolt for connecting strip, (xi) nut & bolt for connect tandem(xii) deto cord end seal (100 nos./pkt), (xiii) 2.1/8" charge tightening wrench, 27.1/2" (698.50 mm) rotary table, 7.1/16" x 10 m double ram bop with accessories, 13.5/8" x 10 m single ram bop with accessories, 3.1/16" x 10 m flexible steel hoses for choke manifold, 3.1/8" x 5 m flexible steel hoses for choke manifold, 2.1/16" x 5m - ss flexible steel hose 3.1/16" x 10m - ss flexible steel hose, 3.1/8" x 5m flexible steel hoses, thermal wellheads for 7" and 9.5/8" casing completion with installation &, commissioning, hose vibrator, rotary hose, drilling in assorted length, 2.34 mm (0.092") piano wireline (well measuring line), static gel strength analyzer, electronic reservoir pressure and temperature measuring gauge., automatic distillation apparatus, ft ir spectrophotometer, rheometer, 350 short ton drilling hook & elevator links (250 short ton, 350 short ton, and 500 short ton), digital acoustic liquid level measuring cum dynamometer equipment, (echometer), cross over, premium box x api eue & pup-joint, 2.7/8", premium in assorted, length, geological thin section preparation unit comprising of cutting, vacuum, impregnation, grinding and polishing equipment and consumables., polarised microscope, pony drill collar, premium tubing, 37.1/2 rotary table, air gas permeameter, double block and bleed isolation plug, gas chromatograph, low to moderate temperature cement retarder, high temperature fluid loss control cement additive, xcd-polymer, xc-polymer (premium), poly anionic cellulose-regular, poly anionic cellulose-super lo, junk sub 5.1/2 inch & 7 inch, 13.5/8-inch x 10000 psi annular bop, 13.5/8-inch x 10000 psi double ram bop., ct reels, super fishing jar, drilling jar, overshots, slammer l
Tender For corrigendum : tender for supply of thermostat for oa 1854 , star delta timer 3 60sec 240v ac 50hz , shaft for fan for ahu , split ac model ftks 71 , liquied line filter drier , core for liquid line filter drier , auxiliary contacts , expansion valve ahu 2 5point6 tr , set of gasket both ends , corrossion protection plug , under voltage relay 415v 50 hz , set of seals for oil cooler , 100a hand change over swithch , 63a hand change over swithch , 160 a mccb , plc electronic module analogue input 6960379 , spares for oil duplex filter , reagent a in plastic bottle 1000 ml , regent b in plastic bottle 50 ml , regent e in plastic bottel 500 ml , regent f in plastic bottle 200 ml , regent g in plastic bottle 500 ml , filter paper 50 nos , fcu 4 fan coil unit , fcu 6 , angle valve 1 4 x 1 4 , gauge pressure compound 0 300 psi 2 dia suction , gauge temp 0point150c dial with 4mtr sensor 6 , main engine f w cooling prpointtransmitter range 0 to 6 bar , gear box s w pressure oulet indicator range 0 to 6 bar , temperature gauges 10 to 50 , temp sensor resistance thermometer pt 100 , starting air pressure transmitter range 0 to 60 bar , starting air pressure indicator range 0 to 60 bar , pcb b1 , electro magnetic valve , drive pin , set of o rings , dry running protection , test cock , level sensing probe , piece distance , gasket , cord type tc air filter insert copper mesh , socket screw , oil separator 7 8 , ring nut , locking washer , thermometer , 5hp 4 pole f 5112m condpointpump motor , gasket , set of spare screws , flow switch , differential pressure relief valve , o ring for filter element , shaft seal , membrance cleaner i , activated carbon , oil seal , oil seal , mechanical seal , kit valve , mechanical seal lp feed pump water , product rotameter , pressure guage 0 140 kg sqpointcm , nc solenoid valve coil 2 way , cd 9 assembly kit , hpointppoint hose 1 bsp , v belt , top cover gasket for cartridge filter , o ring for carbon filter , membrane cleaner ii , membrane cleaner iii , neutralite