Latest quick coupling Tenders | Government quick coupling Tenders

Central Government/Public Sector

CTN :45424816

15 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of set of quick coupling for main transformer of 3 phase locomotives as per clw specification no. clw/es/3/0456, alt-e and confirming to clw drg. no. clw/es/3/sk-4/0456, alt-c. consisting of the following two items (1). male coupling as per abb id no. hstn 422023p003, qty-01 no. (2). female coupling as per abb id no. hstn 422023p0013, qty. 1 no. [ warranty period: 30 months after thedate of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

CTN :45433426

18 Jun, 2026 NA

Uttara Kannada - Karnataka

Tender For tender for supply of rib obm spares - screw m10x50 , screw m6x78 , screw locating , screw , plug drain , screw , screw m8x35 , plug , screw , screw m8x18 , screw , screw m10x45 , screw set m6x3 , screw , screw , screw m10x45 , nut , nut , washer , washer , pin-pivot , cap , check valve , bushing , nyliner , bushing , spring , spring , ball bearing lower , exhaust hose , water hose , fuel filter , ring set-std. , stator assy , gasket set power head , seal kit gear housing , coupling , clutch assly , diaphragm , bellows , anode kit , seal kit , gear housing , filter element , propeller aluminium , guage - water temperature , valve collet , oil drain pump , anode kit 2 , insert-trim adj , o-ring , fuse yellow - 20 ampere , anode kit , link throttle , harness-ignition , cable assy 12 , arm assly rocker , retainer seal kit , cable kit , poppet , bellows assy , universal joint , bolt , filter , fuel , lifter roller , cylinder liner kit , with piston rings , starter , pump assembly - injection , pipe , gasket set , engine , cooler kit , oil , ring set , screw , seal oil , anode kit-alum , o ring , tensioner , potentiometer , filter fuel , belt , hose , bearing assy , repair kit-water , sender assy-trim , belt tensioner , hose , anode zinc , spark plug , o ring 2 , seal-exh. pipe , ring-retaining , ngk zfr5f 4 , gasket , gasket , fuel line-12ft-qs , pump , high , pump , low , gasket , dsh adptr , cable t s g2 12ft , gearcase seal kit , ring set , piston , gasket exh man , trim sender , fuel injector , seal-valve stem , tubing-20 feet , fuse , 20 ampere , hose trim cylinder to connector , enrichner valve , screw m4x10 , water pp repair kit , screw , hose-hydraulic , screw

CTN :45332313

08 Jun, 2026 NA

Bareilly - Uttar Pradesh

Tender For corrigendum : providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - manufacturing unit; supply installation commissioning and succesfull trial of mill drive with 450kw ac vfd motor planetary gear box and rope less coupling with all acces..

CTN :45413730

09 Jun, 2026 NA

Tiruvallur - Tamil Nadu

Tender For supply of civil department lab apparatus - lab items, auger boring machine (motorised) engine type: 4-stroke, air-cooled, single-cylinder petrol engine displacement: 196 cc power output: minimum 6.5 7 hp ( 3.5 kw) maximum engine speed: ~3600 4000 rpm starting system: recoil (manual) start fuel type: pure petrol fuel tank capacity: minimum 1.5 1.6 l supported auger bit sizes: 4 , 6 , 8 , 10 , 12 , 14 (100 350 mm) bit material: heavy-duty mild steel with powder coating typical drilling depth: minimum 3.5 4 ft per bit (800 mm 1.2 m) bit coupling: quick-coupling system for easy bit replacements frame: robust tubular steel frame with ergonomic handles and vibration absorbers weight: minimum 20 22 kg (without auger bit) , flow table apparatus for concrete with accessories dimensions and specifications as per is 9103, table top made from flat metal plate, minimum thickness 1.5 mm. table top size: 700 mm 700 mm, with flatness tolerance of 1.5 mm. table top marked with: scribed cross at centre, lines parallel to table edges and central circle of 200 mm diameter underside of table top reinforced to prevent distortion. total mass of table top: 16 1 kg. table top, base frame front and upper stops provided as per is 9103. lower front edge fitted with two rigid stops to transfer load directly to base frame. base frame designed to transfer impact load directly to supporting surface, minimizing bounce. stop watch digital - 2 nos scale 1 mtr 2 nos mounting wooden platform 300 mm height amc for 3 years inclusive.

Co-operative

CTN :45415201

10 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For fabrication and erection -replacement of the 2" x 2" square bar rails installed on the cane unloader. removal of the old juice gutter from 'a' mill, fabrication and installation of a new one, and conducting a successful trial run. removal of the old m.s. juice tray from 'a' mill, and fabrication and installation of a new one using m.s. plates. fabrication and installation of a new gear guard in the 'a' mill house. welding of worn-out teeth on the mill pinion as required, followed by grinding to a smooth finish. repair of damaged/worn parts of the tail bar coupling by welding as required, followed by grinding. repair of damaged/worn parts of the tail bar by welding as required, followed by grinding. comprehensive repair of the d.s.m. screen: cutting out and removing corroded sections, fabricating and fitting new replacements, repairing all internal piping, and conducting a successful trial run. thorough cleaning of the cane carrier slats, along with their attached links, pins, rollers, and bushes; followed by greasing and refitting said components into the slats in their proper positions. thorough cleaning of the slats, links, pins, bushes, and rollers of the primary/secondary cane carrier chains; followed by greasing, assembling the chain components, and preparing the chain as per instructions. fabrication and installation of juice rings for the rollers. fabrication and installation of mill bearing guards using 3 mm plates. fabrication and installation of m.s. scrapers for the under-feed rollers. cutting of chevron grooves into old mill rollers as required. cutting of chevron grooves into new mill rollers as required. creating 'dots' on the top and feed rollers of the mill using arc-welding electrodes, as per instructions. [repair/replacement of] m.s. components for the worn-out teeth of the under-feed rollers. cutting out patches from a plate and installing them as new teeth. performing arc welding on the grooves of rollers used in the mills using electrodes, as per instructions. fabricating side juice guards for mill rollers from 3 mm plates, as per instructions. fabricating an under-feed roller for the mill in accordance with the provided drawings. dismantling a damaged or defective juice tank in the mill house; fabricating and installing a new tank in its place, and conducting a trial run. replacing or repairing the damaged sections of a defective juice tank in the mill house. dismantling and replacing the bottom plate of a damaged or defective juice tank in the mill house. cane carrier / bagasse carrier / bagasse elevator / cross bagasse carrier / r.b. c. removal of the cane carrier side plate and installation of a new plate. a. welding or forging the enlarged pin holes in the links of the cane carrier, bagasse carrier, etc., to match the specific pin size. a. removal of broken runners from the cane carrier, inter-carrier, bagasse elevator, return bagasse carrier, or cross bagasse carrier, and installation of new runners in their place. a. removal of old, damaged cane carrier slats and installation of new slats. a. the task of drilling holes in new slats for the cane carrier and inter-carrier. a. straightening and repairing cane carrier slats as required. a. repairing damaged and weakened hoods of the cane chopper, cutter, and fibrizer in accordance with instructions. a. removal of old, damaged cane carrier slats; straightening the damaged slats; cutting out the damaged sections; and repairing them by welding in new or salvaged slat pieces cut to size, thereby restoring the slats to their proper dimensions. a. welding the enlarged holes in the inter-carrier links and re-drilling them to the correct size to match the rivets. a. filling the enlarged holes in old inter-carrier slats by welding, and subsequently re-drilling them to create new holes in accordance with the engineering drawings. a. removal of the damaged band from the inter-carrier clutch shaft, fabricating and installing a new one, and conducting a satisfactory

Central Government/Public Sector

CTN :45423329

15 Jun, 2026 NA

Vijayapura - Karnataka

Tender For supply of high pressure hose pair (hre) with quick coupling - 10 meters long [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45390951

15 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For corrigendum : supply of set of quick coupling for main transformer of 3 phase locomotives as per clw specification no. clw/es/3/0456, alt-e and confirming to clw drg. no. clw/es/3/sk-4/0456, alt-c. consisting of the following two items (1). male coupling as per abb id no. hstn 422023p003, qty-01 no. (2). female coupling as per abb id no. hstn 422023p0013, qty. 1 no. [ warranty period: 30 months after thedate of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government/Public Sector

CTN :45405495

22 Jun, 2026 NA

Samastipur - Bihar

Tender For supply of plug for quick coupling arrangement for brake van type bvzc rdso drg. no. wd-91101-s-05 item no. - 01, alt. - 5. spec: 02-abr-02_amdt 4 [ warranty period: 36 months after the date ofdelivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government And Public Sector

CTN :45384707

05 Jun, 2026 NA

Nicobar Island - Andaman And Nicobar Islands

Tender For 86 items of is group c002 - pressure guage plug for regulator unit for aga divator cover holder locking strap spiromatic test diaphragm stop ring hand wheel cover for cylinder pack for aga divator spacing washer cap valve slug assy for cylinder valve for aga divator gland seal shield ring for breating valve with safety pressure gauge hose guide pin lever retaining plate sealing sleeve valve cone quick coupling connection drain button washer sealing spring holder nut balancing diaphram retaining ring head hardness spacer push pad relief valve piston adjusting nut screw blank cover grery valve connection assy valve cone assy o ring 5-pack o ring 10-pack o ring 10-pack o ring 10-pack o ring 3 1x16 10 pack-pack screw 10 pack circlip 10-pack protective cap 3-pack pin 10-pack pin 10-pack burst disc rubber plug 10-pack sealing piston assy inner mask assy grey screw 10 pack oring 81x16 10-pack valve housing assy level assy regulating house valve insert assy mkii w sp complete counter pressure mki pressure equalizing pad regulator unit cw pressure o-ring 10 pack o-ring 10 pack low volume visor innermask strap lovk o-ring screw o-ring divator mask gr nr sp face mask w brea set of special tools and test equipment for is mix diver panel dive control no comms with shut-off valves weight pocket aga bcd jacket with backplate rail inflator cylinder fiqures

CTN :45386616

06 Jun, 2026 NA

Vellore - Tamil Nadu

Tender For supply of civil dept lab items - auger boring machine (motorised) engine type: 4-stroke, air-cooled, single-cylinder petrol engine displacement: 196 cc power output: minimum 6.5 7 hp ( 3.5 kw) maximum engine speed: ~3600 4000 rpm starting system: recoil (manual) start fuel type: pure petrol fuel tank capacity: minimum 1.5 1.6 l supported auger bit sizes: 4 , 6 , 8 , 10 , 12 , 14 (100 350 mm) bit material: heavy-duty mild steel with powder coating typical drilling depth: minimum 3.5 4 ft per bit (800 mm 1.2 m) bit coupling: quick-coupling system for easy bit replacements frame: robust tubular steel frame with ergonomic handles and vibration absorbers weight: minimum 20 22 kg (without auger bit)

Quick Coupling Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Co-operative

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government And Public Sector