Latest rail hoist Tenders | Government rail hoist Tenders

State Government

CTN :45303639

06 Jun, 2026 NA

Ranchi - Jharkhand

Tender For e-quotation for seeking firm rates of plant and machinery and materials category items for preparation/amendment of schedule of rate for the year 2026. - m 1055 - pumps supplying submersible pump sets confirming to is 8034 and motor confirming to is 9283. pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. motor suitable for working on 415v+10%, 3ph, 50 hz, a.c. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shall be suitable for direct coupling. pump shall have suitable outlet as per manufacturers design. anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump., submersible pump set 100 mm dia (with polypropylene/ noryl impeller) up to 20 stages 1 h.p. , 1.5 hp, 2 hp, 2.5 hp, 3.0 hp, 4.0 hp, 5.0 hp, submersible pump 150 mm dia (with bronze/ss impeller) up to 8 stages, 1.5 hp, 2.0 hp, 3.0 hp, 4.0 hp, 5.0 hp, 6.0 hp, 7.5 hp, m 1056 - pressure guage providing fabricating, testing and commisioning pressure vessel fabricating in m.s plate on providing foundation including epoxy paint, pressure gauge (100 mm dia), pressure gauge (150 mm dia), vacuum / combination gauge, m 1057 - lifting equipment chain pulley block supplying triple spur gear type chain pulley block suitable for capacity as below with 3 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark., 1 tonne capacity, 2 tonne capacity, 3 tonne capacity, electric operated circular or rectangular travelling crane (single girder) supplying single girder electrically operated rectangular over head travelling crane with 6 m lift complete with wire rope hoist, class ii duty, all three motions electrically operated by suitable rating motor ip 54, control panel and down pendant control block., 5 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, 7.5 tonne capacity, above 6 m upto 8 m span, above 8 m up to 10 m span, 10 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, m 1058 - lightening arrester, ab switch, insulators, lightening arrestor supplying, erecting approved make thyrite type lightening arrestor suitable for h.t. supply with necessary ancillary material complete on provided cross arm and connected to overhead line., suitable for 11 kv supply, distribution class, suitable for 22 kv supply, distribution class, suitable for 33 kv supply, station class, disc insulator. supplying, erecting porcelain disc type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, pin insulator supplying, erecting porcelain pin type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, air break switch without earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps, suitable for 11kv line, rocking / tilting type, rotating type, suitable for 33kv line, rocking / tilting type, rotating type, air break switch with earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch with earth switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for op

Central Government/Public Sector

CTN :45287725

29 May, 2026 49.41 Lacs

Visakhapatnam - Andhra Pradesh

Tender For running maintenance of technological equipment in converter shop of sms-1.- repair of technological structures in converter shop, mixer discharge spout door rope changing, lance oxygen and water hoses replacement and hose shifting , lance guide minor structural repairs during operation, assistance in removal of lance from thimble socket, converter tilt drive lube oil topping up in lube tank, minor structural repairs of ferro alloy chutes, hoppers and bulk material chutes during converter operation, shifting of stc, sptc&sdc, various running repairs of stc, sptc, sdc, and sample&service car, lime fines screw feeder jamming rectification by cleaning, shifting of mobile equipments like debricking m/c during breakdown in front of converter., tap hole drilling m/c drill bit hard facing, telescopic hoist rope changing/portable repair during relining of converter, well mix pipe changing in l.p bay, steel teeming ladle bell crank lever bracket/ trunnion collar changing, steel teeming ladle bottom purging adapter plate fixing, hot metal tilter /steel teeming ladle resting bracket repair, various minor structural and other repairs like dart pipe centering, tip cleaning and device locking etc in slag cut off device.replacement of charging crane/ mixer crane tilter hook, assistance in shifting jack car and telescopic hoist, minor repairs of lance carriage balancer during operation of converter, minor repairs of lance foldable platform &lance stands, minor repairs of dog house & dog house doors during operation, hot metal ladle spout repair, lub pump changing in revamped converters, shifting, jam cutting and other minor repairs of lance assemblies.

Central Government And Public Sector

CTN :45280929

01 Jun, 2026 NA

Dibrugarh - Assam

Tender For supply of allen key 8 mm , allen key 10 mm , allen key 22 mm , slugging wrench , slugging spanner , reversible ratchet handle half inch , reversible ratchet handle three fourth inch , torque wrench , outside micrometer , soft face hammer 40 mm with steel handle , center punch , straight air drill machine , air grinder , measuring tape , tungsten rotary cutter 6x5mm , tungsten rotary cutter 6x13mm , tungsten rotary cutter 6x10mm , flat file , half round file single cut grades of cut second , half round file single cut grades of cut bastard , half round file double cut grades of cut second , half round file double cut grades of cut bastard , needle file , cutting wheel , grinding wheel or dc wheel , gas cutting torch , welding rod ms 7018 36 h , welding rod ss 308 , welding rod ss 309 , emery paper grade 120 , emery tape fine grade , cleaner , developer , penetrant , rustolene rust disintegrator , wire brush , tefflon tape , tig electrode , air hose pipe wire embadded , masking tape 50 mm , ss wire 1.6mm , ss wire 2.4mm , masking tape 75 mm , half inch impact hexagon bit socket 6 mm drive , half inch impact hexagon bit socket 8 mm drive , half inch impact hexagon bit socket 14 mm drive , half inch impact hexagon bit socket 17 mm drive , size 19mm three fourth inch drive socket 12 point , jack up bolt m10 x 150mm , jack up bolt m12 x 150mm , jack up bolt m16 x 150mm , buff flap wheel , 11mm deep socket 6 point , combination plier , circlip plier set , hydraulic hand pump , hydraulic jack button type , hydraulic jack with hand pump , air micro grinder 120 degree angle grinders 3 collet , air micro grinder 90 degree angle grinders 3 collet , curbide rotary burrs 5x10 mm , curbide rotary burrs 3x15 mm , oil stone size 150mmx50mmx25mm fine grade , klinger gasket 1.5mm, non metallic , tinsnips , cylindrical grinding stone 10x20 mm , taper grinding stone 10x20 mm , taper grinding stone 21x50 mm , cylindrical grinding stone 20x50 mm , chain hoist , triple boiled linseed oil sealing compound , premium polyester rope , dowsil rtv sealant 736 , pneumatic connector with coupling allen key 8 mm,size: lenghth of the long arm=100 mm, lenghth of the short arm=36 mm, moc: chrome vanedium steel, black finsh, allen key 10 mm,size: lenghth of the long arm=112 mm, lenghth of the short arm=40 mm, moc: chrome vanedium steel, black finsh, allen key 22 mm,size: lenghth of the long arm=200 mm, lenghth of the short arm=80 mm, moc: chrome vanedium steel, black finsh, slugging wrench, size: 1 inch,moc: chrome vanedium steel, heavy duty black industrial finish- rust resistant, slugging spanner, size: 3/4 inch,moc: chrome vanedium steel, heavy duty black industrial finish- rust resistant, reversible ratchet handle 1/2'',head dia: 64 mm, head depth: 29 mm, gear action: 32 mm, oal: 605 mm, reversible ratchet handle 3/4'', head dia: 64 mm, head depth: 29 mm, gear action: 32 mm, oal: 605 mm, torque wrench, 1/2 inch square drive, 7-35 kg, widtht: 50 mm, height: 29 mm, length: 805 mm (approx. ), weght: 3.9 kg (approx. )., torque wrench, size :1/2 inch square drive, 25- 135 nm, torque wrench, size :1/2 inch square drive, 50-220 nm, torque wrench, size :3/4 inch square drive, 135-675 nm, outside micrometer, range (200-225)mm, graduation: 0.01mm, material of the frame: stainless steel, material of the spindle and anvil: hardened stainless steel, soft face hammer 40 mm with steel handle, center punch, length: //bid details 2 / 59

Central Government/Public Sector

CTN :45264914

30 May, 2026 NA

Bhopal - Madhya Pradesh

Tender For supply of 2.2 kw ac crane drive , 5.5 kw ac crane drive , 11.0 kw ac crane drive , 22.0 kw ac crane drive , 37.0 kw ac crane drive , 55.0 kw ac crane drive , 75.0 kw ac crane drive 3 phase, digital ac crane drive 2.2 kw, ac drive should be suitable for heavy duty operation of 2.2 kw. offered ac drive should be suitable for crane-hoist operation. if, separate software required for crane application, it must be clubbed with supply of material. ac input voltage: 380 to 480v ac 10%, 3 phase, 3 wire, 50 hz; mode of control: bi-directional fully controlled 3-phase ac; speed regulation: 1% of base speed; braking: suitable dynamic braking resistance and chopper unit (external or in-built); acceleration time: 0.1 to 1000s or better; deacceleration time: 0.1 to 1000s or better; overload: 150%-1min, 200%-3.0s; ambient temperature: 0 to 50 c (derating shall not occur below 50 c. in the event that derating occurs below 50 c, the supplier shall provide a higher-rated drive to match the requirement); rated current at 50 c: min. current should be 5.5 amps at 50 c; high starting torque at low speed: 200% starting torque at 0.3 hz; two analog inputs: two nos. analog inputs having signal voltages of 0 to 10 vdc or 4 to 20 ma (configurable); two analog outputs: two nos. analog outputs having signal voltages of 0 to +/-10 vdc or 4 to 20 ma (configurable); six digital inputs: pnp/npn; one relay output: with short-circuit and overload protection; two digital outputs: with short- circuit and overload protection; brake release signals: outputs braking signals based on inverter operating conditions to prevent cargo bed rollback and overrunning; load adaptive control: when the actual load level is lower than the configured load level, the system can be operated at a ratio-multiplied speed (in terms of the configured frequency), resulting in significantly better efficiency; load ) /bid number : gem/2026/b/7563714 * /dated: 20-05-2026 & & / bid document 1 / 29 frequency), resulting in significantly better efficiency; load limiter: maintains the safety and rescuability of suspended loads by stopping when excessive torque is detected and by allowing operation only in the direction opposite to that in which the excessive load was detected; cooling capacity degradation alarm: detects and displays cooling capacity drop due to cooling fin clogging caused by dust and cooling fan airflow reduction; igbt life expectancy forecasting: estimates the power cycle life expectancy of the main circuit s igbt semiconductor device temperature due to frequent acceleration and deceleration stoppages, and displays the estimate before the design life is reached; protection: it must have all standard protections like stall protection, instantaneous power failure, single phasing, over voltage, under voltage, over current, inverter overload, thermal overload etc; display console: it must have alpha numeric display console for programming of drive, fault display and operating condition; dynamic qr code: it must have dynamic qr code for trouble shooting; tuning facility: it must have auto tuning facility. this must enable perfect matching of motor coupled to load with regards to optimum acceleration time, deceleration time, speed regulation etc; drive programming software: suitable drive programming software along with necessary connecting cable and adapter for connection with laptop and drive should be provided to get online with the offered drive (laptop not in scope); automatic voltage regulation: it must have automatic voltage regulation function to maintain high starting torque even at reduced voltage; regenerative option: it must be capable of regenerative operation; communication protocol: modbus (rtu/serial) or ethernet (tcp/ip); make of drives: fuji- electric/yasakawa/schneider/abb only; suitable dynamic breaking resistance unit of 60% wattage rating of drive, however the value of resistance is to be decided by manufacturer as per their technical manual for crane-ho

Central Government And Public Sector

CTN :45194274

28 May, 2026 NA

Bangalore - Karnataka

Tender For shaft for main hoist gear box of eot crane 1 & 2 as per rwf drg no. 711014411840 . note:- 1) material test certificate for chemical and hardness from the nabl accredited labs should accompany the supply. 2) the shaft should be ut tested for defects and ut certificate from the nabl accredited labs should accompany the supply. [ warranty period: 30 months after the date of delivery ] ]

Central Government And Public Sector

CTN :45167110

02 Jun, 2026 NA

Bangalore - Karnataka

Tender For wire rope hoist of 2t capacity confirming to is-807,3938 with hoist carrier for ct movement to suit 150 mm rail width as per the following specification. equipment : electric wire rope hoist; capacity : 2000 kgs ; duty & class : class iv heavy duty; height of lift : 5.0 mtrs; rail size : 150 mm width, 450 mm height ; hoist head room : 900 mm ; hoist speed : 3 mpm; ct speed : 12 mpm; hoist motor : squirrel cage induction motor 5 hp with brake , tefc sq. cage induction motor 3.7kw / 5hp , 4 pole , class f insulation , 415v , 3 ph , flange mounted , frame size 112m with dc operated electromagnetic brake of minimum braking capacity of 5 kgm, continously rated; ct motor and brake specifications :squirrel cage induction motor power : 0.37 kw , pole : 4, efficiency : ie3 , frame : 71m , mounting : b5 flange , brake : electromagnetic disc type spring loaded ac fail safe brake of min torque : 0.6kg.m; voltage : 415v , phase : 3 phase , compressed spring length : 40 mm , air gap : 0.5 mm; hoist & ct gearbox : helical / spur gear combination. all gears inside the gearbox shall be of en-24 material with hardness of 40-45 hrc. mtc and htc from nabl accredited lab should accompany the supply. wire rope : round strand steel wire rope conforming to is 2266 latest and is 6594 latest size : 10mm or 12mm , 4/1 falls construction : 6 x 36 . drum : seamless pipe of suitable dia & shell thickness to accommodate wire rope single layer as per is-2062; hook : forged heavy duty single shank typeplain hook as per is-3815, 360 swivel type with spring loaded safety latch. control panel :consists of mcb, olar, fuse, etc. note: (a) test certificate for hook shall accompany the supply (b) make of bearings: skf/ntn/fag/timken only. (c)the firm shall furnish inspection certificate from manufacturers or their authorised testing agents preferably incorporating the details of traceability of the bearing. (d) all gears inside the gearbox shall be of en-24 material with hardness of 40-45 hrc. mtc and htc from nabl accredited lab should accompany the supply (e) make of motors: ngef / abb / lhp / cg / hem /bharat bijlee only; (f) make of electricals: siemens/ge/alstom/l & t/abb only ;control voltage: 110v ;supply voltage: 400/440v, 3 phase 50 cycles. (g) guarantee: 12 months from the date of commissioning or 18 months from the date of supply, whichever is earlier. [ warranty period: 18 months after the date of delivery ]

Central Government / Public Sector

CTN :45160212

19 May, 2026 NA

Multi City - Telangana

Tender For auction sale of depot miscellaneous scrap - 128001eot26k, pl- 98325061- 40000 kgs. scrap cond.u/s. eot 40 tones capacity, m&p no.1619.consisting of the details- 1) main hoist motor: 1 capacity-88 kw/118hp, qty- 01no. (2) auxiliary hoist motor- 23kw/30hp-01 no. (3) long travel motor 9kw/12hp-01 no. (4) cross travel motor 17.5 kw/23hp-01 no. (5) inching motor 9kw/12hp-01 no. total motor-05 nos, total copper content-140 kgs (approx). note: delivery by weighment basis. gas cutting permitted for the purpose of loading. note:1) custodian should make the premises clear to facilitate easy loading of the material. he should allow the vehicle inside, up to the location without any hindrance to the movement of vehicle of the purchaser. note: 2) custodian is advised to take all precautionary measures to avoid fire accident while gas cutting. purchaser has to make his own arrangements for cutting, lifting and loading of material and also any other equipment for the purpose and delivery of material. purchaser has to take all safety precautions/care for men & material while gas cutting and lifting of material. location: bin no 8001, power cars shop sc end/cws-lgd. custodian- sse/millwright/ws/lgd, controlling officer- cwm/ws/lallaguda, hsn code- 84261100. gst-18 percent. ss no: s/sd/lgd/insp/2026-27 dt 02.03.26 delivery on actual weighment basis only. special note: overload of the carrying capacity of the vehicle will not be permitted at the time of taking delivery

Central Government/Public Sector

CTN :45064002

23 May, 2026 NA

Ranga Reddy-T - Telangana

Tender For supply of ring spanners set , allen keys long ball point set (1.5 to 10 mm) , allen keys long ball point set (1/16 to 3/8 inches) , hand oil pump , grease gun (lever type) , bucket grease pump with trolley , hydraulic bottle jack 2 ton , hydraulic bottle jack 3 ton , hydraulic bottle jack 5 ton , hydraulic bottle jack 10 ton , bench vice with fixed base , needle files set 140 mm , needle files set 160 mm , drill driver , billet level /spirit level , torpedo level/ spirit level , combination spanner set , shallow offset ring spanner set crv , adjustable wrench 8" , adjustable wrench 12" , long nose plier 6" , long nose plier 8" , plier circlip external (bent) , plier circlip internal (bent) , plier circlip straight external , plier circlip straight internal , curved lock plier mat handle , straight jaw locking plier , slotted screw driver , pipe wrench , hacksaw frame with blade , sledge hammer with wood handle , bearing pullers , line testers , small angle grinder(4 inch) , blower , heavy duty heat gun , welding helmet , mixed tools set , 3 in 1 mobile tools storage box , handheld torch light , polyster webbing sling lifting belt for crane hoist material handling. , combination spanner set (inches) , torque wrench ( 5 to 25 n-m) , torque wrench ( 10 to 50 n-m) , impact drill machine , pipe wrench 450 mm-18" , 1/4 inch sq. drive socket set 6 pt met , oxygen acetylene torch kit (used 13 1 for welding, brazing and cutting) , 1/2 drive pear head ratchet set metric , double open end spanner set

Central Government And Public Sector

CTN :45066384

07 May, 2026 NA

Bangalore - Karnataka

Tender For bush for main hoist lifting beam as per rwf drg no.701014412840. material test certificate should accompany the supply. [ warranty period: 12 months after the date of delivery ]

Central Government And Public Sector

CTN :45066432

08 May, 2026 NA

Bangalore - Karnataka

Tender For output shaft for auxiliary hoist of (40/12.5t)eot-1 crane as per rwf drg no. 701014413550. (including item no.1 to item no.3 as per bom) note:- 1) material test certificate from the nabl accredited labs should accompany the supply. 2) the shaft should be ut tested for defects and ut certificate from the nabl accredited labs should accompany the supply. [warranty period: 30 months after the date of delivery ]

Rail Hoist Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors