Latest ratchet puller Tenders | Government ratchet puller Tenders

State Government

CTN :45303639

06 Jun, 2026 NA

Ranchi - Jharkhand

Tender For e-quotation for seeking firm rates of plant and machinery and materials category items for preparation/amendment of schedule of rate for the year 2026. - m 1055 - pumps supplying submersible pump sets confirming to is 8034 and motor confirming to is 9283. pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. motor suitable for working on 415v+10%, 3ph, 50 hz, a.c. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shall be suitable for direct coupling. pump shall have suitable outlet as per manufacturers design. anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump., submersible pump set 100 mm dia (with polypropylene/ noryl impeller) up to 20 stages 1 h.p. , 1.5 hp, 2 hp, 2.5 hp, 3.0 hp, 4.0 hp, 5.0 hp, submersible pump 150 mm dia (with bronze/ss impeller) up to 8 stages, 1.5 hp, 2.0 hp, 3.0 hp, 4.0 hp, 5.0 hp, 6.0 hp, 7.5 hp, m 1056 - pressure guage providing fabricating, testing and commisioning pressure vessel fabricating in m.s plate on providing foundation including epoxy paint, pressure gauge (100 mm dia), pressure gauge (150 mm dia), vacuum / combination gauge, m 1057 - lifting equipment chain pulley block supplying triple spur gear type chain pulley block suitable for capacity as below with 3 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark., 1 tonne capacity, 2 tonne capacity, 3 tonne capacity, electric operated circular or rectangular travelling crane (single girder) supplying single girder electrically operated rectangular over head travelling crane with 6 m lift complete with wire rope hoist, class ii duty, all three motions electrically operated by suitable rating motor ip 54, control panel and down pendant control block., 5 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, 7.5 tonne capacity, above 6 m upto 8 m span, above 8 m up to 10 m span, 10 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, m 1058 - lightening arrester, ab switch, insulators, lightening arrestor supplying, erecting approved make thyrite type lightening arrestor suitable for h.t. supply with necessary ancillary material complete on provided cross arm and connected to overhead line., suitable for 11 kv supply, distribution class, suitable for 22 kv supply, distribution class, suitable for 33 kv supply, station class, disc insulator. supplying, erecting porcelain disc type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, pin insulator supplying, erecting porcelain pin type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, air break switch without earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps, suitable for 11kv line, rocking / tilting type, rotating type, suitable for 33kv line, rocking / tilting type, rotating type, air break switch with earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch with earth switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for op

State Government

CTN :44271122

03 Jun, 2026 NA

Gandhinagar - Gujarat

Tender For corrigendum : supply, erection, testing & commissioning of wire rope hoist with replacement of existing one for pa fan & air pre-heater area for bmd at gtps.

Central Government And Public Sector

CTN :45280929

01 Jun, 2026 NA

Dibrugarh - Assam

Tender For supply of allen key 8 mm , allen key 10 mm , allen key 22 mm , slugging wrench , slugging spanner , reversible ratchet handle half inch , reversible ratchet handle three fourth inch , torque wrench , outside micrometer , soft face hammer 40 mm with steel handle , center punch , straight air drill machine , air grinder , measuring tape , tungsten rotary cutter 6x5mm , tungsten rotary cutter 6x13mm , tungsten rotary cutter 6x10mm , flat file , half round file single cut grades of cut second , half round file single cut grades of cut bastard , half round file double cut grades of cut second , half round file double cut grades of cut bastard , needle file , cutting wheel , grinding wheel or dc wheel , gas cutting torch , welding rod ms 7018 36 h , welding rod ss 308 , welding rod ss 309 , emery paper grade 120 , emery tape fine grade , cleaner , developer , penetrant , rustolene rust disintegrator , wire brush , tefflon tape , tig electrode , air hose pipe wire embadded , masking tape 50 mm , ss wire 1.6mm , ss wire 2.4mm , masking tape 75 mm , half inch impact hexagon bit socket 6 mm drive , half inch impact hexagon bit socket 8 mm drive , half inch impact hexagon bit socket 14 mm drive , half inch impact hexagon bit socket 17 mm drive , size 19mm three fourth inch drive socket 12 point , jack up bolt m10 x 150mm , jack up bolt m12 x 150mm , jack up bolt m16 x 150mm , buff flap wheel , 11mm deep socket 6 point , combination plier , circlip plier set , hydraulic hand pump , hydraulic jack button type , hydraulic jack with hand pump , air micro grinder 120 degree angle grinders 3 collet , air micro grinder 90 degree angle grinders 3 collet , curbide rotary burrs 5x10 mm , curbide rotary burrs 3x15 mm , oil stone size 150mmx50mmx25mm fine grade , klinger gasket 1.5mm, non metallic , tinsnips , cylindrical grinding stone 10x20 mm , taper grinding stone 10x20 mm , taper grinding stone 21x50 mm , cylindrical grinding stone 20x50 mm , chain hoist , triple boiled linseed oil sealing compound , premium polyester rope , dowsil rtv sealant 736 , pneumatic connector with coupling allen key 8 mm,size: lenghth of the long arm=100 mm, lenghth of the short arm=36 mm, moc: chrome vanedium steel, black finsh, allen key 10 mm,size: lenghth of the long arm=112 mm, lenghth of the short arm=40 mm, moc: chrome vanedium steel, black finsh, allen key 22 mm,size: lenghth of the long arm=200 mm, lenghth of the short arm=80 mm, moc: chrome vanedium steel, black finsh, slugging wrench, size: 1 inch,moc: chrome vanedium steel, heavy duty black industrial finish- rust resistant, slugging spanner, size: 3/4 inch,moc: chrome vanedium steel, heavy duty black industrial finish- rust resistant, reversible ratchet handle 1/2'',head dia: 64 mm, head depth: 29 mm, gear action: 32 mm, oal: 605 mm, reversible ratchet handle 3/4'', head dia: 64 mm, head depth: 29 mm, gear action: 32 mm, oal: 605 mm, torque wrench, 1/2 inch square drive, 7-35 kg, widtht: 50 mm, height: 29 mm, length: 805 mm (approx. ), weght: 3.9 kg (approx. )., torque wrench, size :1/2 inch square drive, 25- 135 nm, torque wrench, size :1/2 inch square drive, 50-220 nm, torque wrench, size :3/4 inch square drive, 135-675 nm, outside micrometer, range (200-225)mm, graduation: 0.01mm, material of the frame: stainless steel, material of the spindle and anvil: hardened stainless steel, soft face hammer 40 mm with steel handle, center punch, length: //bid details 2 / 59

Central Government/Public Sector

CTN :45214323

25 May, 2026 NA

Multi City - Chhattisgarh

Tender For scope of work (sow) as mentioned in tender and schedule of work( 33 )items as given below ,[1] svcng/rep/repl mechanisms of b/saw area 48.000 set,[2] servcng/rep/repl mech. of circular saw 6.000 set,[3] servcng/rep/repl rollers, g/box of conv. 120.000 set,[4] svcng/rep/repl mech. of mobile chargers 40.000 ea,[5] svcng/rep/repl pumps, v/vof hyd p/packs 200.000 ea,[6] svcng/rep/repl sub systems of cnc m/cs 40.000 ea,[7] svcng/rep/repl components of 7 t hmr 20.000 set,[8] svcng/rep/repl axle forging manip 16.000 set,[9] svcng/rep/repl hoist, lt. of e.o.t. cra 40.000 ea,[10] rep/repl water, air. gas lines 52.000 ea,[11] svcng & rep online wheel & axle testng s 20.000 ea,[12] svcng/rep blowers, h/drive, etc of furnc 36.000 ea,[13] svcng/rep/repl componts 63 mn & w/mill 30.000 ea,[14] svcng/rep/repl components of rim spray 16.000 set,[15] structural rep. of fcs, chrgrs, cnc m/cs 20.000 ton,[16] svcng hyd system of mob charger 20.000 set,[17] svcng steerg mech. of mobile charger 40.000 set,[18] tech upkeep of hyd tanks & oth equip 3.000 le,[19] srvcg hyd cyl of press 24.000 ea,[20] up keepg,floor area of wheel forge area 12000.000 ft2,[21] rprg m/tong assy of mill 24.000 set,[22] rprg tracer roll assy 24.000 set,[23] rprg m/carriage of mill 24.000 set,[24] ovhlg /box edge roll 12.000 set,[25] srvcg hyd cyl of mill 24.000 ea,[26] rprg of liftg device 24.000 ea,[27] rprg of t/assy of chgr 24.000 set,[28] techl clng,gas pipeline 152.000 m,[29] disman,fab,main header gas pipeline 32.000 m,[30] clng,gasline,dia18in 82.000 m,[31] clng,gasline,dia8in 86.000 m,[32] fab,damaged gasline 126.000 m,[33] rep,serv of wheel mill gripper system 21.000 set

Central Government And Public Sector

CTN :45167110

02 Jun, 2026 NA

Bangalore - Karnataka

Tender For wire rope hoist of 2t capacity confirming to is-807,3938 with hoist carrier for ct movement to suit 150 mm rail width as per the following specification. equipment : electric wire rope hoist; capacity : 2000 kgs ; duty & class : class iv heavy duty; height of lift : 5.0 mtrs; rail size : 150 mm width, 450 mm height ; hoist head room : 900 mm ; hoist speed : 3 mpm; ct speed : 12 mpm; hoist motor : squirrel cage induction motor 5 hp with brake , tefc sq. cage induction motor 3.7kw / 5hp , 4 pole , class f insulation , 415v , 3 ph , flange mounted , frame size 112m with dc operated electromagnetic brake of minimum braking capacity of 5 kgm, continously rated; ct motor and brake specifications :squirrel cage induction motor power : 0.37 kw , pole : 4, efficiency : ie3 , frame : 71m , mounting : b5 flange , brake : electromagnetic disc type spring loaded ac fail safe brake of min torque : 0.6kg.m; voltage : 415v , phase : 3 phase , compressed spring length : 40 mm , air gap : 0.5 mm; hoist & ct gearbox : helical / spur gear combination. all gears inside the gearbox shall be of en-24 material with hardness of 40-45 hrc. mtc and htc from nabl accredited lab should accompany the supply. wire rope : round strand steel wire rope conforming to is 2266 latest and is 6594 latest size : 10mm or 12mm , 4/1 falls construction : 6 x 36 . drum : seamless pipe of suitable dia & shell thickness to accommodate wire rope single layer as per is-2062; hook : forged heavy duty single shank typeplain hook as per is-3815, 360 swivel type with spring loaded safety latch. control panel :consists of mcb, olar, fuse, etc. note: (a) test certificate for hook shall accompany the supply (b) make of bearings: skf/ntn/fag/timken only. (c)the firm shall furnish inspection certificate from manufacturers or their authorised testing agents preferably incorporating the details of traceability of the bearing. (d) all gears inside the gearbox shall be of en-24 material with hardness of 40-45 hrc. mtc and htc from nabl accredited lab should accompany the supply (e) make of motors: ngef / abb / lhp / cg / hem /bharat bijlee only; (f) make of electricals: siemens/ge/alstom/l & t/abb only ;control voltage: 110v ;supply voltage: 400/440v, 3 phase 50 cycles. (g) guarantee: 12 months from the date of commissioning or 18 months from the date of supply, whichever is earlier. [ warranty period: 18 months after the date of delivery ]

CTN :44774301

26 May, 2026 NA

Mumbai - Maharashtra

Tender For corrigendum : tender for supply of set of wear parts , set of wear parts , threaded spindle , shaft seal , spring plate , coupling , thermocouple , calibration sleeve , pointer , supporting ring , plc binary input/output module 07dc92 , pressure piece , thermocouple , axial compensator , sealing ring , mounting device forsealing rings , turbine nozzle ring complete , compression spring , cooliing system turbine disc complete , supporting device , o ring seal , sealing cover compressor side , gripper , measuring device , bellow , retaining ring , eccentric ring , sleeve , compression spring , strap , bush , o ring seal , plate for adjustable wrench , shackle a0 6 , set of wear parts , main starting valve complete , ring , grip handle , fitting and removing device , outlet valve seat ring , seal , pump impeller , washer , o ring seal , o ring seal , compression spring , holding device , seal , compression spring , sealing ring , retaining ring , counter thrust bearing , supporting device , oil scraper ring , set of wear parts , o-ring seal , sealing ring , support , o ring seal , shaft , retaining ring , pressure gauge , stud , support cup , seal , set of seals , set of wear parts , compensation disk , retaining ring , set of wear parts , sealing ring , overspeed relay type 2 , seal ring , fuel injection valve complete , adapter , fuel pipe , lock nut , seal disk , support , step plate , rope guide , hexagon nut , compressing ring , sealing ring , assembly taper , lower bearing shell , plc kt98 cpu , valve cone piece , indicator pipe , interface relay , o ring seal , o ring seal , o ring seal , butting ring , set of wear parts , guide shoe , set pump element , grinding tool , seal , o ring seal , seal , o ring seal , bush , o ring seal , o ring seal , driver unit em300 , plc analog i o module 07ac91 , valve cone piece , compressing ring , buffle screw with pin , sealing ring , o ring seal , indicator valve , sealing ring , sealing ring , thrust pad , holding device , screwed socket , ratchet puller , o-ring seal , insulation , fuel injection pipe , measuring gauge measuring device , deep groove ball bearing , o ring seal , insert , inlet valve seat ring , o ring seal , o ring seal , o ring seal , upper bearing shell , plc analog input module 07ai91 , sealing ring , set of wear parts , sealing air pipe , set of wear parts , assembly kit for nozlle ring , water jacket , tab washer , set of gasket , set of wearing part soleniod valve , lybrinth ring , hexagon bolt , speed transmitter , lock washer , set of wearing parts , locating ring , terminal box , locking ring , nozzle holder with gasket , shaft seal , mechanical shaft seal , analog input module 07 ai 91 adjusted programmed rfno a501 , pressure gauge ft , roller bolt ft , molykote hb , sealing paste hb , guide bolt , pressure spring nt , bearing bush ft , temperatumre sensor ft , proller bolt zb , thrust piece ft , cylinder pin nt , inlet cam ft , bearing bush ft , lock nut nt , valve piston nt , nut ft , pack of wear parts ts , plc analog i o module 07ac91 , temperatumre sensor ft , lock nut , voltage relay ref no 3a1 , staring valve cone ft , roller zb , lubricant hb , emergency stop button ref no 50s3 , hexagon bolt , lock washeer pair , lock washer pair

Central Government/Public Sector

CTN :45110709

15 May, 2026 NA

Multi City - Tamil Nadu

Tender For auction sale of depot ferrous scrap - cond.& u/s diesel/emu/c&w/lhb, equilising beam, buffer, ac loco components such as tooth gears, crank shaft, brake disc, pinion, injector, gear wheel, cylinder liners, grease cup, alternator fan cover filter assembly, cattle guard, sab air brake components,air brake cylinder components, shock absorber, cattle guard, linear,traction motor spare parts, dust collector, motorman driver seat base with bend, hp cylinder rail guard, outer/inner sleeves of bearing bolts& nuts, air filter, damper, lube oil filter, tiny springs,rotor, anchor link scrap, sab components, cutoff angle cock, control arm upper, ca lower, traction rod, anti roll bar assembly, axle box components, gears, brake disk, leaf spring, carrier assembly, bearing bolt, centering device, fork eye, coupler sleeve, air pipe assembly, break shoe bolster link, hoop coupler, parking break assembly,erclips,primary and secondary springs,footsteps,bolster hanger, dust guard, wearing plate, compensating ring, impeller, inner hanger, safety strip, iron bracket above transformer, brake gear components, spring plate, coupler sleeve, brake hanger, yoke lead, coupler bearing, coupler rear plate, coupler clearance plates, wearing plate, brake beam, dust covers, collar, dashpot top, protective tube, gear case vocer, side bearer cover, pins for hanger, machinery items cut pieces, shock absorber, nipplers, cutout cocks, etc., tm pinion, tm parts as holder plate and end shield, axle box parts as axle box cover,boldter,oilcup,angles,equilising stay,pipes,nosepad,lsbeam,cibrakeblock , automobile parts,silentblock,impeller housing,cowl, axle guide and racer, traction link, the bar, traction housing,brake hangar, pull rod, slack adjuster, knuckle, clevis, screw coupling, cbc coupler and parts, fuffer, cattle guard, labyrinth, bearing for axle box, traction motor and aux motors, damper, sand box, sand ejector, sand pipe, foot step, sand ejector., angle cock and ferrous couplings, lathe machine head, junction box, cutting ferrous, angles, rod, ferrous heater coils, ferrous lamp pipe, transformet brackets, oil lubricator for suspension bearing, lid for gear case, linear, push rod &gudgeon pin, compressor, hood with impeller,ocb ducts, labyrinth, end frame tamper, hanger link, cylinder linear, oil dispersive, axle box cover, servo motor, striker casting with grease adherings(diesel), impeller, guard, compartment sliding doors, compensating ring, end sheild, cartridge with nu bearing,pipe, drum,hoist, gear, impeller, eot crane wheels, eot crane gears , side rod, pull rod, pinion wheel, pull lift chain, door closer, emu coupler,inter cooler, engine head, covers, dooms, pipes, tank, front cover, rear cover, hand rail, after cooler, cylinder body, spring piston, holder plate,sand box, labyrinth, lhb bearings, outer bearing covers, end shield, piston trunk, adjusting rod, palm pull rod, control arm, dbr rf boxes,hoods, brake hanger, brake hanger with head, brake head & semi permanent coupler and parts, bmbc components, bend cover, inspection cover, centrifugal dust collector, cut off angle cock, safety rod, racker arm, valve plate, cylinder bore, bearing cover, emu sliding door, silencer, racer, raiser, bellow plate, door operating cylinder scrap, msu components scrap, labyrinth &pinion shaft(diesel), compensation ring, buff gear, hood with impeller, ront fork complete housing, lb spring set scrap, stator w/o coil, contering dis, anger link with or w/o silent block, oil cup and all other scraps released from diesel / ac loco/emu/c&w/lhb components and all other ms/ci with/without minor non ferrous attachments in as is where is condition. pl no. 98050126. custodian: cdms-rsf-gsd-per. note: 1) cutting permitted to loadable sizes only. 2) during delivery if any major non-ferrous items found the same should be handed over to custodian. 3) loading by crane / jcb is also permitted. location: a row bin 1 & 2

Central Government/Public Sector

CTN :45045738

11 May, 2026 NA

Katipala - Karnataka

Tender For tender for supply of ccr 1 by 2 pneumatic hoist ingersoll rand air motor kit ml1000k amk model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand disc brake kit ml1000k dbk model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand inlet valve kit ml1000 vk model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand pendent kit ml1000 pk model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand filter regulator lubricator unit 3 by 4 inch model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand rotor and shaft kit mhlk 1000mrsh model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand brake piston and brake cover assy mhlk 1000 pbk model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand valve chest and chest plate kit mhlk 1000 mvck model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand pendent handle assy kit mhlk 269me model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand chain wheel assy kit mlk mcwk1 model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand gear frame assy kit mclk25k mca8 model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand load chain kit mlk me745 model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand double line top load hook assy mhlk mek378 model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand double line bottom load hook assy mhlk 1000 ma378 model ml1000k , ccr 1 by 2 pneumatic hoist ingersoll rand housing assy mhl50k ma300 model ml1000k

corporations/Associations/Others

CTN :44996885

30 Apr, 2026 NA

Bengaluru - Karnataka

Tender For auction sale of disposal of static test rig,disposal of electronic-waste (e-waste),disposal of electrical-waste (e-waste),disposal of various types of old, rusted, unusable old scrap ms pipes, etc,,disposal of various old, rusted facilities spare parts/tools, fittings, etc,,disposal of old, used hepa filter,disposal of old, un serviceable motors, pumps, vacuum pumps, valves, hoist etc,,disposal of air compressor system,disposal of three types of liquid nitrogen storage tank,disposal of old, rusted integration tools,disposal of old, rusted gi duct, walk-in coolers panel, tools,disposal of used fuel filters, oil filters, coolant and lube oils etc,,disposal of old, used and dead batteries (hazardous item)

CTN :44928435

08 May, 2026 NA

Kavaratti - Lakshadweep

Tender For supply of workshop tools, machinery and accessories to fisheries department, kavaratti island, ut of lakshadweep - square file smooth., square file rough., flat file, rough., flat file, smooth., flat file, rough., flat file, smooth., flat file, smooth., flat file, rough., flat file, smooth., flat file, rough., round file, smooth., round file, rough., round file, smooth., round file, rough., round file, smooth., round file, rough. 8", double end spanner set (mm) 6 mm 32 mm, double end spanner set (inch) 1/4 - 1 1/2", ring spanner set (mm) 6 mm 32 mm, ring spanner set (inch) 1/4 1 1/2", combination spanner set, box spanner set 6 mm 32 mm, pipe wrench, pipe wrench, pipe wrench, pipe wrench, torque wrench, cutting plier 6 , cutting plier 8 , screw driver 10 , screw driver 12 , hollow punch set, stud remover set, cir clip plier 8 inner,, cir clip plier 8 outer, cir clip plier 6 outer, cir clip plier 6 inner, cir clip plier 10 outer, cir clip plier 10 inner, vice grip plier 12 , screw spanner 12 , nose plier 8 , t spanner set (7mm to 14mm) (pack of 8), hex key set, tubular spanner set, indexable parting tool set,, straight round nose turning tool,, high speed steel tool bit (3piece set),, threading & boring tool set,, 4 flute end milling cutter,, taper shank (twist) drill bit,, hss straight shank drill bit set., centre drill bit set., tap and die set.mm., tap and die set. bsw., tap and die set. bsf., drill chuck with arbor., 1/2 inch 1.1mm bsw carbon steel die nut., 5/8 inch 1.1mm bsw carbon steel die nut., pillar / column drilling machine floor type., portable cut off saw., portable welding machine,, metal-arc earthing clamp,, welding holder., 10 ton 3 jaw hydraulic gear puller., 3 ton engine hoist (crane)., bench vice 6 ,, bench vice 12 ,, vernier caliper 0-300mm,, dial gauge indicator with stand,, pitch gauge (mm),, pitch gauge (inch),, piston ring compressor 4 ,, piston ring expander,, nozzle cleaning set,, angle grinder 4 ,, bench grinder,, welding cable,, welding hand shield,, 3 jaw puller,12 ., stainless steel scale 24 , bench grinding wheel(rough),, bench grinding wheel(fine),, air impact wrench, pneumatic type,, arc welding glass (black)., arc welding glass (plain)., arc welding gloves,, safety goggle.

Ratchet Puller Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors