Get complete information related to latest Reaming Shell Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Reaming Shell Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Reaming Shell Tenders.
Tender For corrigendum : supply of battery operated rotary hammer drill st machine complete with battery pack (02nos), charger, hammer drill bit (4 cutting edge made of tungsten carbide) 10mm 12mm and 16 mm, narrow flat and pointed chiesel single impact energy 2.6j, 1050 rpm, hammer drilling range 4mm to 28mm, optimum drilling range 6mm to 18mm, weight of tool must be less than 3kg, active torque control (atc), inbuilt active vibration reduction (avr), chiseling, chipping, depth gauge, removable chuck, reverse mode, torque clutch, triaxial vibration value for hammer drilling into concrete must be less than 11 (m/s2), triaxial vibration for chiseling in concrete must be less than 6(m/s2), 1st battery 22 (v) 8amp, weight less than 1.5kg, 2nd battery 22 (v)-4amp, weight less than 1.0kg, battery working range minus()17 degree to 60 degree, state of charge display, upgraded durability and battery monitoring ac??? built-in battery health tester, sealed electronics, shock absorbers and reinforced housing to better protect against jobsite conditions, battery charger i/p 230v, o/p power 240, o/p current 9.6amp, state of charge display. , supply of electrically operated concrete breaker with self sharpening chisels (four numbers). 02 nos 36 cm narrow flat chisels, 01 no 36 cm pointed chisel and 01 no 50 cm narrow flat chisel. the tool shall be of the following specification i.e impact energy 35j, impact frequency 1800, vibration to body less than 5m/s2, weight of concrete breaker tool must be less than 15kg, power i/p approximate 2.1kw, brushless motor, detachable supply cord, three lubricating chambers inside machine
Tender For supply of spares - inner tube 3000mm inner tube 3.0 meter underground conentional drilling 48tt part no-8393 0810 55, make- epiroc , outer tube 3000mm outer tube 3.00 meter underground conentional drilling 48tt part no-8393 0810 36 make-epiroc , core barrel comp. 48tt 3000mm complete 3.0 meter core barell underground conentional drilling 48tt part no-8393 0811 62 make-epiroc , spring part no-3716 0268 00 make-epiroc , overhaul kit rotation unit net weight 4591gm, gross weight 4591gm part no- 3716 0248 93 make-epiroc , daimy reamingshell od 48mm, nominal fit for 48tt or ltk core barrel, matrix height 6 inch, matrix rib part no-8370 1749 75 make-epiroc , filter insert complete part no-3716 0107 90 make-epiroc , piston kit net weight 140gm, gross weight 140gm, kit includes piston repair components for trido 45 pump part no-3715 8309 00 make-epiroc , sleeve and p.a.l.s part no-3715 8315 00 make-epiroc , packing kit rotation unit part no- 3716 0248 92 make-epiroc , overhoul kit chuck used in chuck unit kit includes essential parts to restore the chuck unit to optimal working condition. part no-3716 0181 90 make-epiroc , strainer part no-3716 0223 00 make-epiroc , spindle part no-3176 0003 00 make-epiroc , disributor net weight 500gm, gross weight 430gm, integration within the rotation unit and aliged with the spindle part no-3176 0012 00 make-epiroc , core lifter 48tt core lifter underground conentional drilling 48tt part no-3863 2165 00 make-epiroc , core lifter case 48tt core case underground conentional drilling 48tt part no-8393 0810 50 make-epiroc , twin pump 1450rpm part no-3716 0458 00 make-epiroc , guide shoe . part no-3716 1004 00 make-epiroc , packing kit control valve panel net weight 111gm, gross weight 111gm, comprehensive set of sealing components designed to prevent leakage. part no-3716 0186 94 make-epiroc , diaborit core bit sc 10 by 3 excore bit-ltk48-10-13-8- stds125-0 excore bit part no-3760 9180 29 make-epiroc , seal ring part no-6666 000 11 make-epiroc , diaborit core bit sc 10 by 3 excore-10 bit-ltk48-10-13-8-stds125-0 excore bit part no-3760 9180 29 make-epiroc
Tender For corrigendum : supply of goods, machine tools & equipment foran international standard itotin mechanic diesel engine (md) tradeat iti bardoli, gujarat, india (package 3: mechanic diesel - files assorted sizes and types including safe edge file(20nos), flat file, second cut, flat file, bastard, grease gun, grease gun heavy duty trolley type, growler, hacksaw frame, hammer ball peen, hammer chipping, hammer copper with handle, hammer mallet, hammer plastic, hand operated crimping tool, hand vice, hollow punch set of seven pieces, insulated screwdriver, insulated screwdriver, left cut snips, magnifying glass, oilcan, philips screwdriver set of 5pieces, pipe cutting tool, pipe flaring tool, pliers combination, pliers flat nose, pliers round nose, pliers side cutting, engine wire harness connected complete with electrical equipment, diesel fuel quality test equipment set, training setup for adas systems, 4-wheel alignment set & hoist with advanced driver assistance systems (adas), training system for sensors in motor vehicles, training system for the basics of pulse generation and ignition in vehicles, training system: common rail diesel injection system, batterycharger, car jet washer with standard accessories, chain pulley block capacity with tripod stand, compression testing gauge suitable for diesel engine with standard accessories, connecting rod alignment fixture, cylinder liner-dry& wet liner, press fit & slide fit liner, different type of engine bearing model, different type of piston model, fuel feed pump for diesel, fuel injection pump (diesel)inline, fuel injection pump dismantling toolkit /universal vice, fuel injection pump ve pump/ distributor fuel rotary pump (dpc) pumps, glow plug tester, injectormulti hole type, pintle type, injector cleaning unit, injector testing set (hand tester), oil pump for dismantling and assembling., piston ring compressor, piston ring expander and remover., piston ring groove cleaner., radiator cut section-crossflow, radiator cut section-downflow, radiator pressure cap, tandem master cylinder with booster, turbo charger cut sectional view, water pump ford is mantling and assembling, workbench with bench vice and storing drawers, arbor press hand operated 2-ton capacity, drilling machine bench to drill, dual magnetization yoke, grinding machine pedestal (general purpose), hydraulic jack, pipe bending machine (hydraulic type), pneumatic rivet gun with standard accessories, tin smiths bench folder, trolley type portable air compressor, special tools and equipment, hydraulic vertical honing machine for engine cylinder and brake bore, pneumatic valve seat grinder and lapping kit, intercooler cut model assembly with air filter & housing assembly diesel engine, work benches with bench vices and storage draws to demonstrate machines, belt tensioner gauge, granite surface plate with stand and cover, marking out table, multi scan tool, spring tension tester, ammeter dc with external shunt, cylinder bore gauge, dc ohmmeter, depth micrometer, dial gauge, multimeter digital, oscilloscope, outside micrometer, outside micrometer, outside micrometer, outside micrometer, sheet metal gauge, straight edge gauge (2ft.), straight edge gauge (4ft.), surface gauge with dial test indicator plunger type, tachometer (counting type), telescope gauge, temperature gauge with sensor, thermostat, timing lighter, tyre pressure gauge with holding nipple, vacuum gauge, vernier calliper, wire gauge(metric), hydrometer, engineers stethoscope, drill twist (various sizes), hand reamers adjustable, drill twist(assorted), set of stock and dies with die stock-metric, taps and dies complete sets(5types), steel rule, caliper inside with spring, caliper outside with spring, dividers with spring, engineers square, feeler gauge 20blades (metric), hand shear universal, bench lever shears, air blow gun with standard accessories, air ratchet with standard accessories, air impact wrench with standard accessories, angle
Tender For drilling of state govt tubewell for 1.0 cusec discharge 450mm to 676mm dia bore, lowering of pipe assembly 300mmx150mm dia m.s. pipe with direct/reverse rotary rig machine including required all operations (transportations to feeding pea gravel), t&p and labour required for proper completion of work, excluding the cost of material (pea gravel and pipe assembly with accessories as per required & quantity of hsd oil quoted by firm/contractor) provided by the department as above mentioned tubewell site.
Tender For drilling of state govt tubewell for 1.0 cusec discharge 450mm to 676mm dia bore, lowering of pipe assembly 300mmx150mm dia m.s. pipe with direct/reverse rotary rig machine including required all operations (transportations to feeding pea gravel), t&p and labour required for proper completion of work, excluding the cost of material (pea gravel and pipe assembly with accessories as per required & quantity of hsd oil quoted by firm/contractor) provided by the department as above mentioned tubewell site.