Tender For bid to ras supply of supply of adhesion promoting primer (twopack) , supply of pu surfacer (two packs) , supply of pu finish paint ral 9003 (signalwhite) , supply of pu thinner , supply of acetone
Tender For supply of ordinary portland cement 43 grade , fine aggregate sand of best quality , crushed stone graded aggregate 20mm , crushed stone graded aggregate 40mm , quarryed oblique crushed stone graded aggregate of size 63 to 100mm , ms binding wire 0. 90mm dia , ms nails size 1 inch , ms nails size 2 inch , ms nails size 3 inch , mild steel tmt bar 8 mm dia , mild steel tmt bar 20 mm dia , mild steel tmt bar 12mm dia , loop hole with gussol plate comma ralls comma braces comma shuttter etc complate drilled for fixing of steel sheeling or other covering comma doors etc , mild steel door with gussol plate comma ralls comma braces comma shuttter etc complate drilled for fixing of steel sheeling or other covering comma doors etc , 100 mm butt hinges heavy weight colled rold milled steeled complate , 100 mm long ms tower bolt compale , 100 mm long m s handle complate , m and l for 75mm dia pvc swr floor trap comma plain with grating incl jointing with solvent cement complate , pvc swr pipe for fixing in wall of 110 mm dia with gi clip for fixing in wall 2 nos per rm complete , pad lock , integrated water proofing compound , water proof wooden ply board 08 feet long x 04 inch wide x 25mm thick , wooden ballies of 10 feet long , well burnt common building bricks sub class b of size 23 x11. 5 x 7. 5cm , stone setts flooring with stone setts of size 200 to 250mm long comma 150 to 200mm wide and 150mm deep and sides dressed , synthetic enamel paint of approved colour , redoxideprimer , painting brush 4 inch , turpentine oil , wire brush , multipurpose heavy duty gumboots of reqd size of make bata oblique hillson , multipurpose heavy duty latex rubber hand gloves of reqd size and approved make , diesel for concrete mixer ) /bid number: gem/2026/b/7100007 * /dated: 11-01-2026 & & / bid document1 / 29
Tender For corrigendum : procurement of 2k pu paints. - metallic silver 2k pu paint, base coat of different colour - 2k pu paint -orange, ashok layland blue 2k pu paint , base coat of different colour - 2k pu paint new shade blue paint volvo, cng green 2k pu hs paint, mat black 2k pu h.s paint, clear coat 2k pu, putty/polyster putty 2k pu, thinner for 2k pu paint, surfacer primer 2k pu, hardner for 2k pu surfacer primer, ashok layland white 2k pu paint , hardener for 2k pu clear coat, hardener for 2k pu paints, base coat of different colour - 2k pu paint- white, base coat of different colour - 2k pu paint metallic blue
Tender For corrigendum : supply of materials for construction of lingayata veerashaiva graveyard in sirigeri village at siruguppa taluk - display board sfhrte01, pvc pipe of 4kg per cum 63 mm sfhrte01, binding wire sfhrte01, tmt bars fe 500 sfhrte01, granite trap broken metal 100 mm and down size sfhrte01, bitumen washer sfhrte01, gi washers sfhrte01, gi j or l hook with nuts and bolts 8 mm dia sfhrte01, ac sheet 6 mm thick corrugated ac sheet to be used 2 x 20 x 3 x 1.05 equals to 126 sqm 2 x 20 x 2.50 x 1.05 equals to 105 sqm sfhrte01, plumber sfhrte01, add 2percent for fittings and wastage charges sfhrte01, gi pipe 50 mm dia b class sfhrte01, tools & plants and electrical charges at 2percent sfhrte01, add brush at 1percent on cost of paint sfhrte01, enamel metal paint sfhrte01, add handling , loading and unloading at 2percent on material sfhrte01, add providing and removing scaffolding at 3percent on labour sfhrte01, painter class 2 sfhrte01, add wire brush fine steel wool putty sand paper at 3percent on cost of paint sfhrte01, ready mix primer paint ready mix red lead paint sfhrte01, hom of cutting and grinding machine sfhrte01, add sfhrte01, hom of welding and grinding machine sfhrte01, welder grade 1 sfhrte01, corbon electrodes sfhrte01, anchor bolts 750mm sfhrte01, base plate base plate sfhrte01, gusset plates 6 mm thick sfhrte01, ms angle iron 40mm x 40mm x 6mm 23 mtr in length at 3.5 kg per mtr sfhrte01, ms angle iron 50mm x 50mm x 6mm 33.8 mtr in length at 4.5 kg per mtr sfhrte01, burnt bricks class 35 non modular sfhrte01, hom of vibrator 0.71 days sfhrte01, plasticizer super plasticizer sfhrte01, add handling loading and unloading at 1percent on material sfhrte01, casurina poles 100 150 mm sfhrte01, stone chistler class 2 sfhrte01, mason class 2 with tools sfhrte01, mason class 1 with tools sfhrte01, mixer concrete small used in culvert sfhrte01, boulders sfhrte01, bond stone 20 x 20 x 45 cm sfhrte01, size stone 20 x 20 x 25 cms sfhrte01, add watering charges at 1 percent on material sfhrte01, mixer concrete 1 cum capacity sfhrte01, portland cement sfhrte01, coarse sand zone 3 sfhrte01, broken stone aggregate 12 mm to 10 mm size sfhrte01, broken stone aggregate 20 mm size sfhrte01, broken stone aggregate 40 mm size sfhrte01
Tender For construction of madakkathara grama panchayath stadium in ollur lac, thrissur- supply and installation of outdoor gym equipment - open gym equipment, od263824/2025-2026 : chest press (double) - supply and installation of double chest press having the following specifications: dimensions: (l x w x h) 1955 x 710 x 1900 mm. main center pipe - ø 114 mm od ?b? class gi pipe. foundation plate ?m.s. round plate of ø 250mm & 8 mm thick. foundations cover cap- dome shape of pp / nylon / hdpe material. remaining frame - made up of ø 48 mm od ?b? class g.i. pipe. handle - made up of ø48mm od ?b? class g.i. pipe. link - made up of ø 48 mm od ?b? class g.i. pipe. seat & back rest ? 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 integrated wall thickness 3 to 4 mm. bearing bush closing cap?s? pp / nylon / hdpe material. handle must be connected with frame by 8 mm laser cutting ms profile. top closing cap ? dome shape made by pp / nylon / hdpe material.foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brands. pin ? made up of ø 25 mm m.s. bright bar pin. bearing bushes - ø 60 mm od seamless pipe. grips - high quality rubber ø 46 mm od. circlips?a 24 circlips are used for assembly. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zincprimer paint should be applied at all the welding points prior to finishing. (foundation shall be min m20 cc and design shall be approved by the engineer-in -charge before installation.), od263826/2025-2026: air walker - supply and installation of air walker having the following specifications: dimensions: (l x w x h) 1190 x 380 x 1244 mm. main frame- ø 88 mm od "b" class gi pipe dually bending design.foundation plate- m.s. round plate of ø 250 mm & 8 mm thick. paddle ø 42 mm od round gi pipe. handle - ø 33 mm od "b" class gi pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s. plate of 2 mm thick use to support it. top closing cap dome shape made by pp / nylon / hdpe material. closing cap's - pp / nylon / hdpe material. bracket - 8 mm thick laser profile is used to support paddle frame. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing- use is 6005 permanent lubricated reputed brands. pin's ø 25mm m.s. bright bar pin. circlips- a 24 circlips are used for assembly. bearing bushes -ø 60 mm od seamless pipe. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart start & finish position stick on product. all joints must be welded as per is standards and zincprimer paint should be applied at all the welding points prior to finishing. (foundation shall be min m20 cc and design shall be approved by the engineer-in -charge before installation.), od263830/2025-2026 : leg press (double) - specifications: dimensions: (l x w x h) = 1676 x 400 x1500mm. main frame - ø 114 mm od “b” class gi pipe. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. foundations cover cap - dome shape of pp / nylon / hdpe material. link - is ø 60 mm od “b” class gi pipe. seat frame - ø 42 mm od “b” class gi pipe. leg press back rest should be angled in 120 - 130 degree. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 2 mm thick use to support it. seat & back rest – 380 x 275 x 60 mm thick high- density polyethylene (hdpe) blow molded with m
Tender For one panchayath one playground- thanniyam stadium in kallara grama panchayath in vamanapuram lac, thiruvananthapuram- supply and installation of outdoor gym and sports equipment - outdoor gym equipments, od252260/2025-2026 : horse rider - supply and installation of horse rider having the following specifications:dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundationplate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon /hdpe material. remaining frame is made by 48 mm od ?b? class gi pipe. seat frame ?is made by 48mm od ?b? class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od ?b? class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od ?b? class gi pipe. paddle vertical support - 60 mm od ?b? class gi pipe. handle frame- 42 mm od ?b? class gi pipe dually bending design. foot pipe - 33 mm od ?b? class gi pipe. support frame ? 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe.bearing bush closing cap ? pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft.foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand.bearing bushes - 60mm od seamless pipe. pin ? made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips ? a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zincprimer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252261/2025-2026 : back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od ?b?class g.i. pipe. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od ?b? g.i pipe. seat rest pipe ? 42 mm od ?b? class g.i pipe. handle pipe ? 33 mm od ?b? class g.i pipe.footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 3 mm thick used to support it. footrest pipe ? 42 mm od ?b? class g.i pipe and 80 x 40 mm ms rectangular pipe. closing cap ?pp / nylon / hdpe material. seat ? 360 x 300 x 2 mm thick m.s. seat with corner fillet for safety. grips - high quality rubber 46 mm od. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zincprimer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252262/2025-2026 : cross trainer (double) - supply and installation of double cross trainer having the following specifications: dimensions: (l x w x h) 2280 x 550 x 1650 mm. main frame- made of 88 mm od ?b? class gi pipe dually bending design. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. paddle vertical support - 42 mm od ?b? class gi pipe. handle - 33 mm od ?b?class gi pipe dually bending design. leg movement frame ? 50 mm x 50 mm x 2 mm thick square pipe. footrest - cast iron 124 x296 x 5 mm thick and m.s. plat