Tender For repair of vehicals c c - steering gear box overhauling kit , front axel major repair lit bearing oil seal gasket kit lock washer bearing outer cone , reverse gear union , reverse gear conractor , main relay set , 30a fuse chamber set , 4x4 contactor wall set , 4x4 adopter , 4mm wire , the above mention repair steering gear box remove and clean all parts and send to the lathwork rectified the fault replaced the damaged parts services and reassemble to fit the vehicle. , clutch assy , pressure plate set , pressure release bearing set , clutch master cylinder assy , clutch repair master kit , vacuum cylinder hose head assy , clutch pedal bearing set , clutch top rod assy , synchorinzer cone , synchorinzer ring , shift slivering , shifter assy , reverse gear bearing , extra gear bearing , connection shifter rail , main shaft oil seal , gear box packing kit , reverse gear wheel assy , extra reverse gear wheel assy , gear top fit assy , gear sleeves assy , ignition switch , starting coil relay with base assy , pump solenoid switch , 30 a fuse base assy set , 5mm wire , door inches set , door lock set , main realy , holding realy , the above mentioned break down veh remove the clutch assy housing clean the all parts replaced the damaged parts reassembles to fit the veh the above mentioned the gear box remove the gear box , 4x4 adopter assy , 4x4 connector valve assy , door winding mechanism set , wire 4mm , break synchronizer ring , break cylinder major repair kit , c washer set , the above mentioned 4x4 wiring check and replace the damged parts and burn wire and check the veh on road test done , right door lock inches , left door lock inches , the above mentioned door removed the damaged parts replace the door inches door lock and tilting and tinkering work completed to refit the veh check and tested , wind screen replaced ) /bid number : gem/2025/b/6746294 * /dated: 01-10-2025 & & / bid document 1 / 30
Tender For tender for supply of safety articles at gtps : : - safety net with over lay net, size: 10 mtr.x, 5mtr., mesh size: 100 mm, mesh rope size: 4 mm, material: high stength polypropyline., full body harness, 3 piece pvc suit for protection against chemicals containg pant, coat and face piece with visor, boiler suit (apron), barricading tape red & white tubing roll with "danger" & "caution" written., gum boot which offer resistance to acid and alkalis., aluminium pipie step wall mounted ladder,, size: 14 feet., alluminium ladder self supported 'a' type, having 08 feet length, alluminium ladder self supported 'a' type, having 10 feet length, ceramic fiber blanket, long rang rechargeable torch with charger., industrial vacuum cleaner.motor, specification: watts capacity: 1200 w max.,, voltage: 220-240 volts a/c supply, capacity: 15 ltr, all standard accessories., traffic cone, fire proximity suit
Tender For supply of coal mill spares for coal mill unit-3, 4 & 5 at gandhinagar tps. - keeper ring for upper bearing, air seal ring for roller journal assembly of coal mill #384, cap screw lock of roller journal assly b/00235-1, cap screw lock of bull ring segment locking ring b/00235-ii, journal assly lock plate (drg.ext-b00273), vertical plate for mill dust guard chamber b/00801 r1, bowl hub cover for mill bcp 2360/77, oil bracket with nipple and pipe for roller assembly of coal mill bcp 2360/77, scraper for coal mill, bowl top liner for coal mills of unit 3&4, bull ring locking ring for mills of #3&4 gtps., body liner, size: 1575 mm outer radius,, 2150 mm cord length, 700 mm width and 12 mm the. for coal mill xrp 883, set of vane for classifier as per gtps/bmdii/00648, 36 nos/set, mill body liner for coal mill type bcp 2360/77 at gtps., end cover for roller journal shaft for bcp 2360/77, lower bearing keeper plate of journal assembly for coal mill bcp 2360/77, oil seal keeper plate of journal assembly for coal mill bcp 2360/77, trunion bushing retainers for journal head and trunion shaft assembly for coal mill bcp 2360/77, scraper guard assembly gtps/extn/b-, , journal assembly stop bolt with nut, housing for stop bolt of roller, dust protection cover for mechanical face seal of "stein" france coal mill type bcp 2360/77 for #3&4, dust protection assly (two halves), b/00782, inverted cone for coal mill #3&4