Latest refrigerant pipe Tenders | Government refrigerant pipe Tenders

State Government

CTN :45303639

06 Jun, 2026 NA

Ranchi - Jharkhand

Tender For e-quotation for seeking firm rates of plant and machinery and materials category items for preparation/amendment of schedule of rate for the year 2026. - m 1055 - pumps supplying submersible pump sets confirming to is 8034 and motor confirming to is 9283. pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. motor suitable for working on 415v+10%, 3ph, 50 hz, a.c. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shall be suitable for direct coupling. pump shall have suitable outlet as per manufacturers design. anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump., submersible pump set 100 mm dia (with polypropylene/ noryl impeller) up to 20 stages 1 h.p. , 1.5 hp, 2 hp, 2.5 hp, 3.0 hp, 4.0 hp, 5.0 hp, submersible pump 150 mm dia (with bronze/ss impeller) up to 8 stages, 1.5 hp, 2.0 hp, 3.0 hp, 4.0 hp, 5.0 hp, 6.0 hp, 7.5 hp, m 1056 - pressure guage providing fabricating, testing and commisioning pressure vessel fabricating in m.s plate on providing foundation including epoxy paint, pressure gauge (100 mm dia), pressure gauge (150 mm dia), vacuum / combination gauge, m 1057 - lifting equipment chain pulley block supplying triple spur gear type chain pulley block suitable for capacity as below with 3 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark., 1 tonne capacity, 2 tonne capacity, 3 tonne capacity, electric operated circular or rectangular travelling crane (single girder) supplying single girder electrically operated rectangular over head travelling crane with 6 m lift complete with wire rope hoist, class ii duty, all three motions electrically operated by suitable rating motor ip 54, control panel and down pendant control block., 5 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, 7.5 tonne capacity, above 6 m upto 8 m span, above 8 m up to 10 m span, 10 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, m 1058 - lightening arrester, ab switch, insulators, lightening arrestor supplying, erecting approved make thyrite type lightening arrestor suitable for h.t. supply with necessary ancillary material complete on provided cross arm and connected to overhead line., suitable for 11 kv supply, distribution class, suitable for 22 kv supply, distribution class, suitable for 33 kv supply, station class, disc insulator. supplying, erecting porcelain disc type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, pin insulator supplying, erecting porcelain pin type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, air break switch without earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps, suitable for 11kv line, rocking / tilting type, rotating type, suitable for 33kv line, rocking / tilting type, rotating type, air break switch with earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch with earth switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for op

State Government

CTN :45268513

05 Jun, 2026 NA

Bankura - West Bengal

Tender For supply delivery and fitting fixing of gaseous chlorination items for the standby system of clear water pumping station and supply of 1 no empty chlorine tonner at ibs uporgora under chhatna, saltora block sub-surface water based piped water - supply and delivery of gaseous chlorination unit spares (0-10kg) & (0-4kg)kg/hr. require of wallace & triman evoqua, vacuum regulator (wall/cylinder mounted)with auto switchover facility, capacity 0-10 kg/hr max, evoqua make s10k scale controller, capacity 10.0kg/hr, manual control, evoqua make 1 injector suitable for 40 psi backpressure, fitting fixing of the above new supplied spares on the existing position part by part with new ejector pipe line with necessary fitting materials and necessary welding job by expert mechanical complete the job as per direction of eic and as per is:10553., supply and delivery at site of 1000 kg empty chlorine tonner hydraulic test pressure 30 kgf design as per asme section viii div.1 with hot-forged steel hook and a safety tongue piece, add: 18% gst, add: 1% cess

State Government

CTN :45268542

05 Jun, 2026 NA

Bankura - West Bengal

Tender For supply delivery and fitting fixing of gaseous chlorination items for the standby system of clear water pumping station and supply of 1 no empty chlorine tonner at intake kukrakuri under chhatna, saltora block sub-surface water based piped - supply and delivery of gaseous chlorination unit spares (0-10kg) & (0-4kg)kg/hr. require of wallace & triman evoqua, vacuum regulator (wall/cylinder mounted)with auto switchover facility, capacity 0-10 kg/hr max, evoqua make s10k scale controller, capacity 10.0kg/hr, manual control, evoqua make 1 injector suitable for 40 psi backpressure, fitting fixing of the above new supplied spares on the existing position part by part with new ejector pipe line with necessary fitting materials and necessary welding job by expert mechanical complete the job as per direction of eic and as per is:10553., supply and delivery at site of 1000 kg empty chlorine tonner hydraulic test pressure 30 kgf design as per asme section viii div.1 with hot-forged steel hook and a safety tongue piece, add: 18% gst, add: 1% cess

Central Government/Public Sector

CTN :45235182

26 May, 2026 NA

Multi City - Maharashtra

Tender For auction sale of others - scrap released industrial waste products unserviceable for railway use 1 coal /coke ashes debris steam coal and hard coke dust scrap pieces of u/s fire bricks 2 broken piece of plain and color glass mirror porcelain washbasin commode crockery item etc.3 u/s cotton rag canvas released from coaches old unusable hand gloves aprons etc 4 u/s rubber items window sealing rubber foam pieces gas rubber hose pipes shutter felts damaged & condemned rubber hose and pvc pipe pieces damaged torn vacuum hose pipes without universal couplings small broken pieces of rubber released from roof of the coaches & glass wool 5 unusable timber plywood wooden scrap pieces of compreg ply broken slates pieces of berth shutter panel etc scrap broken pieces of released packing wood timber jolly board condemned wooden seats without rexene & ferrous fittings wood shavings mixed with sand & rubbish 6 released packing material rubber fibre wooden polythene bags gunny bags card board paper puttah gatta thermocole etc. broken and u/s pieces of asbestos cement sheets released from shops 7 unserviceable old lp sheet including pop rivet seat berth number plate unuseable off cuts of new lp sheet unusable pieces of limpet /nftc sheet 8 floor sweeping consisting of sand mud mud muck scrap paper shrubs tree branches including dried grass & leaves coach-rust rusty nails screws and washers u/s aluminum rivets mixed with sweepings and ashes from burn material mud and muck includes unserviceable pieces of stones boulders broken concrete foundations and u/s pieces of other bricks oily greasy rags oily dirt and mud mixed with rubbish heaps excluding sludge oil 9 unserviceable off-cuts of fresh rexene pvc sheet coir recron foam released and unserviceable rexene pvc sheet coir recron foam 10 unserviceable frp products like window shutters louvers inlay lavatory wall protectors wash basin fish tails banjo shutter front cover or axle box mouldings 11 u/s nylon plastic bushes nylon wire rope and other nylon items broken welding hand screen helmet face shield 12 u/s bakelite bakelite box with screws broken and condermned bakelite cover of tumber switch and fuse without non-ferrous fitting mcb with embedded material except aluminum and copper, ceramic pieces plastic pvc sheet and sleeves broken pieces of electric switches battery floats flexible pipes unserviceable broken tube lights and bulbs fuse without non-ferrous fittings broken damaged pieces of insulating material 13 engineering garbage not required by iow and generated inside workshop like tree branches loose earth etc 14 following unserviceable items released from poh activities -bp and fp houses with end ferrous parts, unserviceable buffer pads and draft pads, frp main door embedded with ferrous window bars handle latch etc frp window shutters with embedded ferrous material, unserviceable lavatory door vestibule door fiied with latch/handle and ferrous mouldings etc, hdpe commode chute with ferrous bracket and supporting ring,plastic spool with end pieces of filler wire. 15 ferrous pieces mixed with rubbish weighing not more than 500gms 16 any item of industrial waste not covered above as advised in writing by the site engineer in charge. as is where is basis. loading by purchase. location of material : site c i.e. 100 kld etp plant/lower parel workshop/ maharashtra. custodian :sse/ys/pl(total approximate weight 50 mt.) note 1)the above items are expected generation of various items in the workshop. the railway does not guarantee availability of all types of industrial waste at all times in the same proportion some item may be even zero 2)the railway will not accept any claim for availability of any specific items or their quantities 3)no material other than above shall be permitted to be lifted 4)mode of delivery will be in metric tonne. no sorting & pick and choose of material will be allowed.

CTN :45302604

08 Jun, 2026 NA

Gwalior - Madhya Pradesh

Tender For supply of front wheel spoke outer re , hydraulic distributer head assy als , vane pump als , part set of seals als , supporting plate als , assy oil filter safari , assy fuel filter safari , solenoid als , fixing bracket assy als , mounting bracket als , muffler comp mg , rubber hose for vacuum pump safari , rubber hose uc pipe to egr cooler safari , gaskit cylinder head mg , timing device piston tata , distributor head tata , assy injector safari , condenser fan scorpio , brake pad r808 scorpio , blade wiper front scorpio

CTN :45201311

30 May, 2026 NA

Birbhum - West Bengal

Tender For procurement of miscellaneous items for u-3 oh under ahp-mm deptt at bktps - materials, u-clamp,m16 for 8 in ci pip for ahp bktpp moc: ms; size: 232mm dia,308mm length,75m ( with 02 nos of nuts and 02 nos of washers for each u-clamp ), u-clamp 16 mm dia with 02 nos nuts & 02 nos washer# for 150 nb ms line ( with 02 nos of nuts and 02 nos of washers for each u-clamp ), pipe bend (short),50nb,90 deg for ahp bktpp moc: ms is:1239,heavy grade,without flange ( thickness not less than 5.54mm ), pipe bend (short),100nb,90 deg for ahp bktpp moc: ms is:1239,heavy grade,without flange ( thickness not less than 8.58mm ), pipe bend (short),80nb,90 deg moc: ms is:1239,heavy grade,without flange ( thickness not less than 8.08mm. ), union,ms-25 nb, nipple ms-25 nb, elbow ms-25 nb # ( thickness not less than 4.55mm ), elbow,1/2 in for 12x10 diffuser feeder air line ahp-1 bktpp moc: gi,with both ends inside threaded, pipe bend (short),65nb,90 deg for ahp bktpp moc: ms is:1239,heavy grade,without flange ( thickness not less than 7.01mm ), nipple,1/2 in for 12x10 diffuser feeder air line ahp-1 bktpp moc: gi,length-50mm, union,ms-15 nb, elbow 150nb,90 deg for ahp bktpp moc: ms is:1239,heavy grade,without flange ( thickness not less than 10.97mm ), counter flange for 150nb ms pipe for ahp bktpp moc: ms; od-280 mm,id-170 mm,pcd-240 mm,holes-08 nos,hole dia.-20 mm ; 01 set=02 nos, counter flange for 80nb ms pipe for ahp bktpp 01 set=02 nos, nipple ms-40 nb, nipple ms-15 nb, pipe bend - 45 deg. , 65nb,ms is: 1239 make-blue sta ( thickness not less than 7.01mm ), tee,1/2 in for 12x10 diffuser feeder air line ahp-1 bktpp moc: gi,with all ends inside threaded ( moc: ms ), elbow 90 deg # moc-ci bs1211 class d,size-10",ahp-i# for fa line ( moc- ni-chrome alloy ci, hardness-400bhn min, bend min working pr-0.55ksc(16"hg),working in vacuum line.wetting head. ), turn buckle,gi ( type-eye to eye, eye hole should be for m20 bolt total length-1350mm, thk-20mm square section-50x250mm ), bend pipe, 90 deg, 40nbx40nb,ms seamless for wet ash system moc-ms thk-3.7mm as per sch 40 steel pipe, reducer 25x15mm ms # with both end inside pipe thread, counter flange for 400nb ms pipe for ahp bktpp as per ansi-16.1 ; class 125,flat face; 01 set=02 nos ( 1st : 8 set flanges flange od: 630mm flange id: 410mm pcd: 580mm no. of hole: 16nos. hole size: 20mm flange thickness: 20mm 2nd : 7 set flanges flange od: 595mm flange id: 410mm pcd: 545mm no. of hole: 12nos. hole size: 20mm flange thickness: 20mm ), counter flange for 100nb ms pipe for ahp bktpp as per ansi-16.1 ; class 125,flat face; 01 set=02 nos

CTN :45292467

01 Jun, 2026 NA

Jhansi - Uttar Pradesh

Tender For supply of starter im t , vdcvdc converter actia make , pump hydraulic ram hand driven , horn valve , hose 650 mm , manual brake valve wabco , assy injector , assy vacuum hose for tc , pipe assembly

CTN :45261594

30 May, 2026 1.07 Lacs

Baramulla - Jammu And Kashmir

Tender For supply of black screw , 2 core copper wire 2 point 5 mm , 5 amp switch board with 3 switch modular , floor carpet 26 ft x 5 ft , vacuum cleaner , nail 2 point 5 inch , pvc flexible pipe 1 inch , socket 16 amp and 6 amp , acrylic bd , photo frame

CTN :45254893

27 May, 2026 NA

Jamshedpur - Jharkhand

Tender For supply & testing of high vacuum type transformer oil filtration machine of capacity: 1000 lph for 415v, ac, 3 phase operation, operating temperature range 40' c - 70' c and conform to is: 60341989 (reaffirmed 2005), compact type with dimension not more than length: 2.0 mtr. and breadth: 1.0 mtr. including suitable size of trolley and wheel with all accessories. the machine shall include suction pump with flow rate 1 hp 20 lpm, motor capacity (cg/havells/siemens/kirloskar make), vacuum pump motor capacity 0.75 hp (cg/havells/siemens/kirloskar make), magnetic strainer, degassing chamber capacity 95 itr or higher, suitable size dirt bag. the cost is inclusive of complete set with powder coating painted control panels, protection devices, flow meter to monitor volume of oil filtered, temperature gauge, safety relief valve, inlet & outlet pipe each of 10 mtr. length and all accessories necessary for transformer oil filtration operation. the machine shall be capable for removal of moisture, gas and solid particles and achieve breakdown voltage(dielectric) 270 kv post filtration. after supply, contractor shall arrange demonstration, training on operation, maintenance and troubleshooting in presence of concerned ssee(g) & staff/operator. make: cbs technologies/ sbe or reputed make conforming to is as approved by dee(g)/ckp before supply, gad of filtration plant set with details of all parts including trolley, wheel etc. shall be submitted to dee(g)/ckp for approval. [warranty period: 30 months after the date of delivery ] ]

CTN :45236118

02 Jun, 2026 34.64 Lacs

Murshidabad - West Bengal

Tender For supply and installation and commissioning of different machineries and tools of dihipara beekeeping cluster, dihipara, murshidabad under wbkvib during the year 2026 27 2nd call - supply and installation and commissioning of raw honey storage tank specification:fabricated from 304 grade 3 mm thick stainless-steel sheet, all joins argon welded and polished. one number manhole is provided on top. both top and bottom is dished type.capacity 1200 kg, supply and installation and commissioning of honey processing plant 1. ms control panel - 012. ss channel and angel structure - 013. pre heating tank in coil shape - 014. microfine replaceable cartridge filter press with gear pump - 015. processing tank with 1 nb coil - 016. falling film evaporator with ms stand - 017. wate ring vaccum pump 3 hp + water pump - 028. cooling tank with 1 nb pipe coil - 019. settling tank - 0210. set of ss pipes for honey piping - 0111. set of gi pipes with specials for water pump fitting -01specification:1. one no stainless steel prefilter tank having thickness of 1.6mm with volumetric, capacity of 500 kg along with 500 micron mesh.2. gear pump: made by m/s. rotodel company with full stainless steel body and gears. basic output capacity: 2000 its/hour. it will be suitably reduced to give required output.3. drive motor: 1.00 h.p. 3 phase 440 vol tefc 1440 rpm make crompton or siemens.4. pre-heating tank: made from 2.0 mm thick stainless steel sheet with heater.5. microfine filter: full stainless steel self locking high pressure filter which has poly propylene filters made of 40 micron size,6. processing tank: made from 2.0mm thick stainless steel sheet. one set of coil will be provided for processing tank.7. crompton make water circulation pump 0.50 hp, mono block, with 18 m head, 230 volt ac single phase mechanical seal.8. falling film evaporator: made from 3.0 mm thick stainless steel sheet, with concentric cone in side. subjected to vacuum and ensuring falling film, to evaporate moisture.9. cooling tank: made from 1.5 mm thick stainless steel sheet, exactly same as pre-heating tank but without heaters.10. settling tank: made from 2.0 mm thick stainless steel sheet, top and bottom dished ends fully leak proof, bottom drain for honey withdrawal.11. control panel: having cut off mcb, control circuit fuses, and mcb in each time to protect the wiring, with brass earthing bolt to prevent electric shocks.12. water ring vacuum pump: 1.0 hp, 3000 rpm, 440 volts ac, tefc. kirloskar make with 750+mm 4g vacuum.13. ms chasis made out of 75x40 ms channel in two parts., supply and installation and commissioning of semi automatic volumetric honey filling machine, twin head, stroke typespecification:this is specially designed to fill squash/juice in bottles. all contact parts are made from 304 type stainless steel materials, supported on mild steel angle structure, covered with stainless steel sheet. the machine is suitably arranged to upper and lowering of filling head with nozzle so that there is no spillage of squash or juice while filling. this helps to fill in accurate measure.no bottle no filling system.operated by 1 hp motor with gear box.filling capacity: 100ml to 500 ml.filling speed: 14/16 bottles per minute., 500 ml to 1000 ml, supply and installation and commissioning of twist off lug cap sealing machine:specification:for 100% leak proof airtight sealingno hand pulling system.this machine is ideal way to hermetically seal bottles products with twist off/vacuseallug caps to preserve taste and flavour.semi-auto-manual and pneumatic working.capacity: 600 bottles/hr of 53 to 63 mm caps. (for 200 and 400 gm. pickle)supply is complete with air compressor., supply and installation and commissioning of weight scale digital display specification:capacity: 100 kgreadability: 10 gm, supply and installation and commissioning of digital refractometer, supply and installation and commissioning of shrink tunnel specification:seals pp/pvc shrink film.separate controls for h

Refrigerant Pipe Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

Central Government/Public Sector