Get complete information related to latest Relay Station Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Relay Station Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Relay Station Tenders.
Tender For supply of 2.2 kw ac crane drive , 5.5 kw ac crane drive , 11.0 kw ac crane drive , 22.0 kw ac crane drive , 37.0 kw ac crane drive , 55.0 kw ac crane drive , 75.0 kw ac crane drive 3 phase, digital ac crane drive 2.2 kw, ac drive should be suitable for heavy duty operation of 2.2 kw. offered ac drive should be suitable for crane-hoist operation. if, separate software required for crane application, it must be clubbed with supply of material. ac input voltage: 380 to 480v ac 10%, 3 phase, 3 wire, 50 hz; mode of control: bi-directional fully controlled 3-phase ac; speed regulation: 1% of base speed; braking: suitable dynamic braking resistance and chopper unit (external or in-built); acceleration time: 0.1 to 1000s or better; deacceleration time: 0.1 to 1000s or better; overload: 150%-1min, 200%-3.0s; ambient temperature: 0 to 50 c (derating shall not occur below 50 c. in the event that derating occurs below 50 c, the supplier shall provide a higher-rated drive to match the requirement); rated current at 50 c: min. current should be 5.5 amps at 50 c; high starting torque at low speed: 200% starting torque at 0.3 hz; two analog inputs: two nos. analog inputs having signal voltages of 0 to 10 vdc or 4 to 20 ma (configurable); two analog outputs: two nos. analog outputs having signal voltages of 0 to +/-10 vdc or 4 to 20 ma (configurable); six digital inputs: pnp/npn; one relay output: with short-circuit and overload protection; two digital outputs: with short- circuit and overload protection; brake release signals: outputs braking signals based on inverter operating conditions to prevent cargo bed rollback and overrunning; load adaptive control: when the actual load level is lower than the configured load level, the system can be operated at a ratio-multiplied speed (in terms of the configured frequency), resulting in significantly better efficiency; load ) /bid number : gem/2026/b/7563714 * /dated: 20-05-2026 & & / bid document 1 / 29 frequency), resulting in significantly better efficiency; load limiter: maintains the safety and rescuability of suspended loads by stopping when excessive torque is detected and by allowing operation only in the direction opposite to that in which the excessive load was detected; cooling capacity degradation alarm: detects and displays cooling capacity drop due to cooling fin clogging caused by dust and cooling fan airflow reduction; igbt life expectancy forecasting: estimates the power cycle life expectancy of the main circuit s igbt semiconductor device temperature due to frequent acceleration and deceleration stoppages, and displays the estimate before the design life is reached; protection: it must have all standard protections like stall protection, instantaneous power failure, single phasing, over voltage, under voltage, over current, inverter overload, thermal overload etc; display console: it must have alpha numeric display console for programming of drive, fault display and operating condition; dynamic qr code: it must have dynamic qr code for trouble shooting; tuning facility: it must have auto tuning facility. this must enable perfect matching of motor coupled to load with regards to optimum acceleration time, deceleration time, speed regulation etc; drive programming software: suitable drive programming software along with necessary connecting cable and adapter for connection with laptop and drive should be provided to get online with the offered drive (laptop not in scope); automatic voltage regulation: it must have automatic voltage regulation function to maintain high starting torque even at reduced voltage; regenerative option: it must be capable of regenerative operation; communication protocol: modbus (rtu/serial) or ethernet (tcp/ip); make of drives: fuji- electric/yasakawa/schneider/abb only; suitable dynamic breaking resistance unit of 60% wattage rating of drive, however the value of resistance is to be decided by manufacturer as per their technical manual for crane-ho
Tender For tender for supply of ac under voltage_over voltage circuit of solid state sensing type alv-d2 for ov , input surge protection network (mov based) in-20ka , imax-40ka up-2.2kv , current transformer 80 a / 5 a , cl 1.0 , 5 va , current transformer for ac ammeter am1 , 75a/5a , cl1.0 , 5va , emc filter (ac side) (mf-423-3-3d-80a-440vac , case r4) 440 v , 80 a ac , emc filter (ac side) (mf-423-3-3d-60a-440vac , case r7) 440v/60a ac , surge suppressor mov for ac input 275 v/20d (mov1-3) , surge suppressor mov for ac input 510v ac (k510) (mov 4-6) , control transformer for ac auxiliary supply 456 / 240vac , 500va , cooling fan with fan failure alarm contact 230v ac , 6 inch , 50w , 3ph , ac power capacitor 7.5kvar , 480v , 3ph , ac power capacitor 10kvar , 480v , ac reactor for pfc1 25a , 1550 micro henry , three phase , double wound , impregnated naturally air cooled mains transformer 50.03 kva (456/300v) , three phase , double wound , impregnated naturally air cooled mains transformer 38.21kva (456/40v) , semi-conductor hrc fuses for the rectifier bridge 80et , 690v , semi-conductor hrc fuses for the rectifier bridge 690v/500a (500mmt) , rectifier fuse fail detector circuit for rectifier fuse 220v dc , rectifier fuse fail detector circuit for above fuse 24v dc , diode skkd101/16 , scr1 12 425 a 12nos (425a/1000piv) , d1 300a 300a/600piv , interphase transformer 1.238kva , interphase transformer 1.13kva , shunt for cpc1 , cpc2 sh 100a/75mv , shunt for cpc1 , cpc2 sh 600a/75mv , bleeder resistance 350 ohm 750w 2 in parallel , bleeder resistance 50 ohm 100w 4 in parallel , bleeder resistance 2k 50w 2 in series , bleeder resistance 50 ohm 50w , dc overload circuit of solid state sensing type for 110 percent overload alarm and trip function , dc overload circuit of solid state sensing type for 110 percent overload alarm and trip function 230v ac 744 a , dc overload circuit of solid state sensing type for 150 percent overload alarm and trip function 230v ac 177a , dc overload circuit of solid state sensing type for 150 percent overload alarm and trip function 230v ac 1014 a , filter choke 118 a 650 micro h , filter choke 676 a 16.5 micro h , filter condenser fuse fail detector circuit 220v dc , filter condenser fuse fail detector circuit 24v dc , 3 phase scr full controller card for scr firing 220v dc , 3 phase scr full controller card for scr firing 24v dc , 2 c_o plug in type auxiliary relay with base for ineterlock 240v ac 2c_o mpc , 2 c_o plug in type auxiliary relay with base for b2.4v function and interlock 240v ac 2c_o mpc , 2 c_o plug in type auxiliary relay with base for b2.75v function and interlock 240v ac 2c_o , double disk type wire wound potentiometer to adjust output voltage in float mode 10k _3w , potentiometer pcb for voltage control circuit for cpc1 and cpc2 mt 120a , potentiometer pcb for current control circuit for cpc1 and cpc2 mt 121a , rectifier dc over voltage circuit of solid state sensing type for alarm indication pfc and trip function , rectifier dc over voltage circuit of solid state sensing type for alarm indication pfc and trip function , rectifier dc under voltage circuit of solid state sensing type for alarm indication pfc and trip function , rectifier dc under voltage circuit of solid state sensing type for alarm indication pfc and trip function , 2 c_o plug in type auxiliary relay with base for trip latch function 240v ac 2c_o mpc , charger silicon blocker diode diode skr300_12 , 300a_1200 piv , 2 c_o plug in type auxiliary relay with base as contact multiplier for mccb4 220v dc 2c_o , load under voltage circuit of solid state sensing type for alarm indication and pfc , load under voltage circuit of solid state sensing type for alarm indication and pfc , load over voltage circuit of solid state sensing type for alarm indication and pfc , load over voltage circuit of solid state sensing type for alarm indication and pfc , load over voltage circuit of solid state sensing type for pfc and trip function , d
Tender For corrigendum : supply of door switch for illuminating lamp as per annexure 1 , door switch for led tube as per annexure 1 , emergency stop push button as per annexure 1 , hrc fuse and link as per annexure 1 , indicating lamp as per annexure 1 , time delay relay as per annexure 1 , under and over voltage with phase failure and phase reversal protection relay as per annexure 1 , motor protection on delay timer 1no plus 1nc as per annexure 1
Tender For corrigendum : procurement of spares for il-78 aircraft - 63 unit control heating, electronic altimeter, arm 62t self contained servo unit rudder installation, relay box 66, relay box 024, left pilot additional speaker, fire extinguisher, kursmp.70 control panel, csd turbine, actuator, fixture, control unit, tape transport mech block, tank unit, pump booster(v), bulb - temperature (v), semi automatic parachute release unit, v trailing edge inner wing (l h), te vane inner wing flap rh sec 2, outer wing flap rh, pipe exhaust, shutter, fuel oil heat exchanger, auto start control, receiverbsi-3k-7, sweep unit, power unit, input information, receiver(av2.026.004.2.03 sp), unit, valve eletro hydraulic, low frequency unit, monitor auto pilot (v), oxygen mask, gear distributive, device(yam2.087.067-01), pannel, switch - power failure, memory block, magnetic recorder, rectifier unit, pcb,y-5, pcb,y-6, differential switch (pressure), sensor
Tender For pump motor protection relay with phase failure, overload and dry run protection & under/over voltage protection, auxillary supply: 415 v ac. similar to minilec make model: s2cmr1. make: minilec, gic, schneider only required. [ warranty period: 12 months after the date of delivery ]
Tender For supply, installation, testing and commissioning of kutch and jamnagar islanding scheme as per technical specifications and scope of work. - ufr, 66kv sub-statin, rtu or equivivalent device, mfm in 66kv ss, gsm modem, 8 port switch, di card, do card, pt fuse, 66kv panel, 220kv sub-station, mfm for 66kv feeder, 220 & 132kv rtu, ai card, di card, do card, mfm for 220kv lines, cmr relay, cable for cmr relay integration, cable for mfm integration work, control cable for ufr wiring, control cable for ufr wiring, 0.5sqmm shielded cable for di/do, wiring, 12core 1.5sqmm armoured control, cable for di/ do wiring - from sic, panel to c&r panel, workstationwin 10 pro/intel 17/32 gb, ram/ 1 tb ssd, printer, ldms software, cyber security component, l3 switch at sub-station, l2 switch at sub-station, l3 switch at control centre, auxillary relay, rj45 lan cable, gps, annunciator, earthing cable for rtu and ufr panel, pt fuse, dc failure relay, 220v master panel, 220kv sic pane, 220kv slave panel, sikka 220 and sikka 132kv, connection, fodb 48 pair, liu, fo switch
Tender For corrigendum : supply of spare of lt vfd at hurl sindri on oem basis - dual temperature transmitter, filter capacitor for sine wave filter, current transformer ratio - 100/1a, vfd control device, vfd power device, hrc fuse link bs type, fuse holders & isolating link, hrc fuse bs type, fuse-link rating-80a, ac 690 v., fuse base nh din type, "6"" output filter ral 7035 size 6 incfan failure and temp detection unitiop (intelligent operator panel)power contactor rating-45a, 230v ac", "sine wave filter reactor rating -22kwpanel fanmulti-function meter (mfm)32-50 a, thermal overload relay""", circuit breaker with electronic trip, panel door mounted rotary op. handles, d series dc drm relay, d series drm relay socket, 4 contacts, d series ac drm relay, 5a, d series ac drm relay, 10a, d series drm relay socket, 2 contacts, digital indicator (rpm meter), transformer, 415vac/240vac, 500va, auto transformer, 22kva 3 pole, current transducer specs-4-20ma, motor restart timer, green push button & contact block, red push button & contact block, selector switch, 2-way, selector switch, 3-way, blue push button & contact block., yellow push button & contact block, black push button & contact block, fuse terminal, thermostate, high current connectors, 40mm insulator, 30mm insulator, indicating lamp, red, indicating lamp, yellow, indicating lamp, blue, indicating lamp, green, indicating lamp, amber
Tender For supply of siemens make components d d - contactor power 3rt1065 coil voltage 220v acdc with 2no2nc aux contacts , contactor power 3tf53 coil voltage 230v ac with 2no2nc aux contacts , contactor power 3tf50 coil voltage 230v ac with 2no2nc aux contacts , contactor power 3rt2037 1ne30 65 amp coil voltage 48v dc with 1no1nc aux contacts , contactor power 3tf32 coil voltage 230v ac , contactor power 3rt20351al20 coil voltage 230v ac with 1no1nc aux contacts , mccb 3va14635ee320aa0 630 amp , relay bimetal 3ua5800 2vz1 57 to 70 amp , timer 3rp15051aw30 0.05 sec to 100 hrs 24 240v dcac , timer 3rp1525 1bw30 8k 0.05 sec to 100 hrs 24 240v dcac , 5sl42027rc 2a 2p mcb , mcb 5sl44407rc 40amp 4ptpn , contactor aux 3th 3040 oaro , phase failure monitoring relay 3ug5512 1ar20 , relay 3ua 5000 0.8 to 1.25 , contactor 3th3040 0apo 230v ac , contactor aux 3th3022 0apo 230v ac , contactor aux 3th3022 0bm4 coil voltage 220vac , contactor aux 3th3022 0bm4 220v dc , over load relay 50 to 200 amp , contactor aux 3rh2140 1ap008k 230v ac , contactor power 3rt2037 1np30 65 amp coil voltage 220v dc , power contactor 3rt1054 48v dc , power contactor 3rt 1054 220v dcac , mccb 3vm1116 5ee32 0aao 160 amp , mccb 3vm1220 5ee32 0aao 200 amp , thermal overload relay 3ru2156 5ew10 8k 140 200 amp , 3kl8221 5ta10 sfu 125 amp , mccb 3vm1220 4ee32 0aao 200 amp , 3na78320rc hrc fuse 125a hrc type vsb size 00 , contactor 3rt1055 6ap36 200 220v acdc with 2no2nc contact block , position switch metal enclosure 40 mm device connection 1x m20 x 1.5 1 no 1 nc rotary actuator right left adjustable with adjustable length metal lever 100 mm long and stainless steel roller 19 mm , analog adjustment monitoring relay phase failure phase sequence asymmetry and under voltage monitoring 3x 160 690 v ac 15 70 hz 2 changeover contacts screw terminal , power contactor 3rt2024 1bm40 ac 3 12 a 5.5 kw 400 v 1 no 1 nc 220 v dc , auxiliary switch transverse 3rv2901 1e 1no1nc , signalling cont block model 3vu9131 7aaoo , auxiliary block 3rv2901 1a 1no1nc , mpcb 3rv2011 1ea10 2.8 4amps with aux block , mpcb 3rv2011 1ja20 7 10amps with aux block , fixed and moving contact for 3tf4702 0mb4za01 kit 3ty7 470 0ya , mpcb 3rv2031 4ea10 22 32a , sentron switch discon 3ld main switch 3 pole 32 a power at 400 v 11.5 kw , mcb single pole 5sl4104 7rc 4a , mcb single pole 5sl4106 7rc 6a , auxiliary block 5st3010as 1no1nc for mcb , mcb 5sl52047rc 2pole 400vdc 4a , power contactor 3rt2037 1np30 with 1no1nc block and with add on block 2no2nc 3rh29111ha22 , 3rt2026 1ag20 power contactor 25 a 1no 1nc coil 110 v ac 50 60 hz , 3rt2025 1ag20 power contactor 17 a no 1 nc coil 110 v ac 50 60 hz , 3tf3110 0afo contactor 12 a ac 3 110 v , 3rh21221afoo contactor relay 2 no 2 nc 110 vac , 3tf4602 0apoza01 2 nos 3ty7561 1ka008k coil voltage 230v ac tp air break contractor 45a coil 230v 4no4nc , 3tf3400 0apo 2 nos 3tx4010 2a 3tx4001 2a coil voltage 230v ac top mounted block 2no2nc tp air break contractor 32a coil 230v 2no2nc , 3tf3200 0apo 2 nos 3tx4010 2a 3tx4001 2a coil voltage 230v ac top mounted block 2no2nc tp air break contractor 16a coil 230v 2no2nc , 3th3031 0apo 4 nos 3tx4010 2a coil voltage 230v ac top mounted block 7no1nc aux contractor 10a coil 230v 7no1nc //bid details 2 / 64
Tender For multi functional monitoring relay 3 phase, 3 wire/4 wire with adjustable thresholdes, adjustable triping delay, monitoring of phase sequence and phase failure, voltage monitoring (under and over voltage), installation 35 mm din rail conforming tostandard en 60255-6, rated supply voltage 280-520v ac with self extinguishing properties as per rdso specification no-rdso/pe/spec/ac/0184-2015(rev.1) & rdso letter no.el/7.1.108/mssbc dtd 17.09.2021 to abb model no.cm mps, 41s or carlo gavazzi model no.dpc01dm48.400/480 or simens model no.7ug0818-ica20 or schneider model no.rm22tr33 or dold model no.bd9080.12 or phonex model no.mr-es-3 v-400( 1217805) or l&t model no.mg53bh l&t mg53bh. [ warranty period: 30 months after the date of delivery ]