Latest rheology equipment Tenders | Government rheology equipment Tenders

Central Government/Public Sector

CTN :45263257

23 Jun, 2026 NA

Delhi - Delhi

Tender For supply of uhv deposition chamber - uhv chamber specification (vacuum better than 2 10-9 mbar uhv) chamber overview spherical (diameter 14 ) or equivalent square shaped uhv chamber with support frame equipped with three (3) x 2-inch magnetron sputtering sources. all cf flanges and uhv viewports/ss blanks, three (3) x 2-inch magnetron sputtering sources. each sputtering source has an individual gas inlet line for process gases. all cf flanges., substrate holder : diameter: 2 inches; heating molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature to 1000 c without rotation. rotation: substrate holder can rotate continuously, driven by a stepper motor. variable speed from 0 to 10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to the substrate surface, tilt adjustable. two sputtering sources mounted confocally at an angle relative to the substrate. base pressure: lower than 2 10 mbar (ultra-high vacuum)., vacuum pumping system: turbo molecular pump: pfeiffer hipace300 / edwards next 300 / leybold turbovac 350i with cf100 flange or equivalent with integrated controller, ion pump with controller: included to maintain uhv vacuum levels and provide clean pumping., backing pump: pfeiffer hiscroll 12 / edwards nxds 15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves : one cf100 and one cf150 manual gate valves for isolating the chamber from the pumping systems as well as throttling, vacuum gauges and measurement: one cold cathode gauge with readout capable of measuring vacuum pressures down to1 10-10 mbar for precise uhv monitoring., one capacitance manometer gauge with measurement range from 1 10-1 to 1 10 mbar for accurate pressure reading during deposition phase, gas delivery system: two independent mass flow controllers (mfcs):a. one mfc (0-100 sccm) for argon gas feeding to all three sputtering sources via high vacuum valves.b. one mfc (0-100 sccm) for nitrogen gas feeding directly into the chamber with its own high vacuum valve.gas lines for ar and n2 are physically separated to avoid cross-contamination., chamber access and viewports: 1. two view ports installed on the chamber, each equipped with manual shutters. 2. access ports for gauges, pump, gas inlet and few spares for future upgradation., baking capability: entire chamber designed to bake-out at 150 c to reduce contamination and out gassing during operation, cooling capability : water manifold with flow switch / flow meters, near uhv chamber specification: chamber overview: spherical (diameter 14 ) or equivalent square shaped uhv chamber with stand., three 2-inch magnetron sputtering sources, each with individual gas inlet. all cf flanges and uhv viewports/ss blanks., substrate holder: a. diameter: 2inches; heating : molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature (rt) to 1000 c without rotation b. rotation : substrate holder driven by stepper motor. variable speed from 0 to10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to substrate surface (tilt able preferred). two sputtering sources mounted confocally at an angle. base pressure : lower than 5 10 mbar (near uhv)., vacuum pumping system: turbo molecular pump : pfeiffer hipace 700 / edwards next 730 / leybold turbo vac 900 ix or equivalent with cf100 flange and integrated controller, suitable for near uhv vacuum., backing pump: pfeiffer hi scroll 12/edwards nxds15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves: one cf150 manual gate valve to isolate / throttle chamber from pumping system, vacuum gauges and measurement: cold cathode readout capable of dis

CTN :45311622

09 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of lab equipments - beesley s balance count : manual , overall dimension of unit : length x depth x height, 535mm x 140mm x 230mm 21 x 5.5 x 9 , net weight of the unit : 6.2 kg (13.6 lb), gsm cutter cutter type: circular, hand-operated cutting area: 100 cm ; blade : circular hardened stainless steel blade , water bath capacity : 400 ml x 12 pots; maximum temperature : ambient to 90 c; accuracy : 1 c; capacity (in liters) of main both : 25 liters (approx.); pot size : inner dia. : 79 2 mm; length : 122 mm; temperature controller : digital, pt 100 sensor ( 0.1 c accuracy); heater capacity : 3000 watts; bath size : 675 x 235 x 160 mm; power supply : single phase 220vac @ 50hz; consumption : 3050 watts; s ize(wdh) : 1100 x 350 x 250 mm; weight : 25 kg , crock meter rubbing finger shape: cylindrical; diameter: 10 0.1mm; diameter: 10 0.1mm; force: 9 0.2 n; stroke length: 100-110 mm; direction: straight line , back and front , hygrometer measurement range: 20- 80 %rh; accuracy : 2% rh; temperature measurement range: 20 - 30 c; sensor type: capacitive humidity sensor; response time 30 seconds, twist tester gauge length : 2 to 20 inch (5 to 50 cm); counting system : direct result; in-built calculations; readout in dot-matrix display; control system : microcomputer based pre-selectable / pre-programmable solid-state circuitry control user-friendly menus with membrane keypad assembly; programmable parameters : measurement unit, sample length & type, twist direction and speed index, etc.; elongation setting range : - 10 to + 100 mm; tensioning range : 1 to 90 grams (by calibrated augment weights); power supply : single phase 220vac @ 50hz; consumption : 100 watts; applicable standard(s) : astm d1422 / d1423 and is 832; physical dimensions : size (wdh) : 1000 300 200 mm; weight : 12 kg; swift/wheel circumference : 1.5 yards or 1 , yarn appearance board winder tapered board : 01 no. parallel board : 01 no; main unit : 01 no. bobbins holder stand : 01 no., crimp tester measuring length : 60 cm; tension weight : 35g; net weight of the unit: 5 kg., thickness gauge measuring range : 0.010 to 10.00 mm measuring accuracy : 0.01 mm (or) 10 microns readability : 0.01 mm; diameter of anvil : top : 75 0.2 mm physical dimensions : size (wdh) : 150 110 160 mm; weight : 4 kg (accessories included) , wrap reel meter number of leas made at a time : 10 spread of each lea : 20mm 5 counter (three digits) : digital pre-set counter with sensor operating speed : 100 5 rpm motor : 1/8 hp 230v geared motor

corporations/Associations/Others

CTN :44946861

27 May, 2026 12.90 Lacs

Aligarh - Uttar Pradesh

Tender For corrigendum : providing of system integration service to implement iot sensor-based measurement and monitoring of rural water supply systems - comprehensive annual maintenance contract for preventive and breakdown maintenance of installed instruments, hardware and software etc for online continuous ..

CTN :44652558

07 May, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of propeller pump coupling with acoustic wheel , circlip , spare kit ra , mechanical seal , impeller nut , shaft liner-sleeve , impeller , hexagonal fitted screw , collar nut , cable gland , rim v200 st1-50d , rim st vp100 , worm 100 1-30d mhi32 s1 , worm 200 1-50 d mhi32s1 , drive sleeve , immovable rim , coupling rotex , hexagonal nut , hexagonal nut , hexagonal fitted screw , split lip seal dint480 ls aft-gearbox p28 , minor kitsee kit g053 , flat gasket for aft low speed seal suport , seal ring a26x34 for ball valves and nozzles , casing gasket 274.7283.9x0.5 , mechanical seal complete u3.0d , driven lube oil pump spares set , sea water driven pump spares set , 3mm thick shim , plate locking pin hs , plate locking pin lower case , hs fore-ls fore inspection door gasket , hs aft inspect door gasket , adjusting shim , adjusting shim , switch 4 positions , flat gasket for aft low speedseal support , gearbox 3 ways ball valve dn40 , gearbox 3 ways ball valve symetrical dn40 , gearbox 2 ways ball valve dn25 , gearbox 2 ways ball valve dn40 , steel ball valve with npt 1-2 threaded sleeves - nd15 , filter for fan , starboard seawater driven pump , generic diffrential pressure switch , differential pressure switch series f , relative pressure transmiter 0-10 bar 4-20ma without display , excess pressure valve on oil system , shftline rpm transmitter , fastener bellows , thrust sensor , thrust measurement electronic cabinet , thrust measurement cabinet spares set , seawater pump coupling , split lip seal dint270 hs fore , reinforced bellow nd 200 , bellow nd 200 , bellow nd 40 , reinforced bellow nd 50 , bellow nd 50 , temperature transmitter type pt 100 l-110 , temperature transmitter type pt 100 l-65 , temperature transmitter type pt 100 l-77 , adjusting shim for seawater pump , adjusting shim seawater pump square , adjusting shim 230x 320 for sea water pump support , gasket for pump and heater , seal ring a26x34 for ball valves and nozzles , mechanical seal , multiple actuator , viton oil seal 70 110 8

CTN :44963673

05 May, 2026 1.54 Crore

Mysore - Karnataka

Tender For supply, installation, commissioning, testing, training and maintenance of instrumentation of taraka dam in mysore district of karnataka state under drip-ii (package-3) - world bank aided. - automatic water level recorder, weather station, uplift pressure measurement system, jelly filled cable, cable termination and switch box, spvc cable, laying of armoured jelly filled cable, providing and installing of digital readout unit, providing and installing of data collection unit and transmission system server, settlement plate/survey markers, data collection unit and transmission equipment, providing and installing of electronic sirens, providing installation and commissioning of tilt meters, vibrating wire piezometer/pore pressure meter, drilling of 1 mts bore holes, pair armored jelly filled cable of standard, cable termination and switch box-2, laying of armoured jelly filled cable-2, pvc pipe, v noutch, slope stability analysis, masw test to estimate dynamic soil constant, installation charges, installation charges for drainage gallery instrumentation, total station, amc

CTN :44802326

29 Apr, 2026 NA

Goa - Goa

Tender For providing of custom bid for services - annual maintenance contract for upgraded acoustic range for fy 2026-28 (two year) - nuwr (goa) -, uwrjb-under water junction box, amu-acoustic measurement unit, interconnect cable, dhs- data handling system, computer system with software for dhs, rcs, online & offline aac, range test jig, range calibration equipment jig

CTN :44774586

20 Apr, 2026 NA

Delhi - Delhi

Tender For supply of water level sensor (seepage) l-10 general specifications item : water level sensor (tank) 1. float shape: biconical eco- the sensor uses a biconical eco-shaped float for measuring water levels. 2. cable: neoprene- the cable of the sensor is made of neoprene material.3. service: waste water/sewage- this sensor is suitable for use in waste water and sewage applications. 4. contact rating: 8a, 250 vac- it has a contact rating of 8 amperes at 250 volts ac. 5. maximum temperature: 85 c- the sensor can operate in environments with a maximum temperature of 85 degrees celsius. 6.maximum test pressure: 3.5 kg/cm2- the sensor can withstand a maximum test pressure of 3.5 kilograms per square centimeter. 7. length of wire: 10 mtr- the sensor comes with a 10-meter long wirefor connecting to a control system. 8. number of floats: one- this sensor utilizes a single float for its level measurement. 9. terminal enclosure x cable entry: cast ai ip66 x pg11 cable gland- the terminal enclosure is made of cast aluminum (ai) and is rated ip66. it includes a pg11 cable gland for cable entry. 10. process connection moc x type: the material of construction for the process connectiondetermines th ecompatibility of the sensor with the fluid or medium in the tank. the moc should be stainless steel, brass, plastic, or other materials depending fluid in the tank. 11. system configuration:adjustable stopper - the sensor has an adjustable stopper as part of its system configuration. 12. pr. cn (pressure connection): 4" nb bs-10 t d- the pressure connection is a 4 & quot; nominal bore (nb) as per bs-10 table d standards. 13. moc (material of construction): pp (polypropylene) - the sensor is primarily made of polypropylene material. 14. pressure rating: 1 kg/cm2- the pressure rating for this sensor is 1 kilogram per square centimeter. 15. switch type: microswitch (1 spdt)- the sensor is equipped with a microswitch with a single-pole, double- throw (spdt) configuration. ]

State Government

CTN :44668101

13 Apr, 2026 NA

Itanagar - Arunachal Pradesh

Tender For supply, installation, and commissioning of the laboratory items-computerised multi cylinder diesel engine test setup with programmable open ecu, computer, pfil /urea /water methanol injection, pficng, pfih2, hcci vaporisor fumigation, vibration sensor vs125, icenginesoft, automatic bomb calorimeter with printer, rotating viscometer, air-conditioner test rig with humidification & dehumidification system, thermal conductivity of metal rod apparatus, thermal conductivity of liquids apparatus, heat transfer in forced convection set up, heat transfer in natural convection set up, emissivity measurement apparatus, vernier caliper (digital), mechanical comparator, outside micrometer ,ring gauges ,laser displacement sensor ,pressure sensors, autocollimator ,pc based analog & digital motor control trainer ,noiseless air compressor ,flight controller

Central Government/Public Sector

CTN :44699518

22 Apr, 2026 NA

Prayagraj - Uttar Pradesh

Tender For pre and post tamping track measurement survey using trimble gedo vorsys trolley system in section under aden/line/cnb & provision of water level indicator for rcc over head tanks (27 nos.) under aden/hq/ii/cnb.