Latest road light panel Tenders | Government road light panel Tenders

State Government

CTN :45317702

01 Jun, 2026 NA

Delhi - Delhi

Tender For supply of domain make capacitors panel spares for various sites under ae(e and m)-iv - s/f of heavy duty capacitors, rated at 415v, 50 hz 3 phase ac, mpp type make : domain: 1. 5 kvar, s/o microprocessor based apfc relay 8 steps with digital display of power factor and parameters make : domain, s/f of tp contactor cap-24 50 a. make : domain, s/o voltmeter 0-500 v. make : domain, s/o ammeter 0-1000 v. make : domain, s/o rack on indicator lamps. make : domain, s/o sensing ct 150/5a. make : domain

CTN :45332966

11 Jun, 2026 NA

Rourkela - Odisha

Tender For supply of electrician screwdriver thin stem insulated handle , electrician screwdriver thin stem insulated handle , knife double bladed electrician , neon tester , blow lamp brass , crimping tool , wire cutter and stripper , copper bit soldering iron , de soldering gun , contactor and auxiliary contacts , limit switch , rotary switch , relay cut out relays reverse current relays over current relays under voltage relays , pin type shackle type egg type and suspension type insulators , hydrometer , portable electric drill machine , load bank lamp or heater type , laboratory type induction coil , out side micrometer , knife switch dpdt fitted with fuse terminals , knife switch tpdt fitted with fuse terminals , earth plate , earth electrode , mccb , elcb , rccb , fuses , rheostat sliding type , capacitors , various lamps , bus bar with brackets , rubber mat , electrician helmet , safety belt , ohm meter series type and shunt type portable box type , digital multi meter , a c voltmeter m i analog portable box type housed in bakelite case , milli voltmeter centre zero analog portable box type housed in bakelite case , ammeter mc analog, portable box type housed in bakelite case , ac ammeter mi analog portable box type housed in bakelite case , kilo wattmeter analog , digital wattmeter , a c energy meter , power factor meter digital , frequency meter , magnetic flux meter , lux meter , tachometer , tong tester or clamp meter , megger , 3 point d c starter , 4 point d c starter , wheat stone bridge with galvanometer and battery , single phase variable auto transformer , phase sequence indicator , growler , ac starters , oscilloscope dual trace , function generator , soldering iron , temperature controlled soldering iron , discrete component trainer , linear i c trainer , digital i c trainer , electric induction plate , electric kettle , electric iron , immersion heater , a c ceiling fan and ac table fan , geyser storage type , mixture and grinder , washing machine semi-automatic , motor pump set , inverter with battery , voltage stabilizer , dc power supply , battery charger , current transformer , potential transformer , solar panel with battery , ink jet or laser printer , dc compound motor with starter and switch , thyristor igbt controlled d.c. motor drive with tacho generator feedback arrangement , thyristor igbt controlled a.c. motor drive with , electrical machine trainer , used dc generators series shunt and compound type for overhauling practice , motorised bench grinder , manual motor coil winding machine , ceiling fan coil winding machine , primary current injection set , stepper motor with digital controller , shaded pole motor , smart meter , ev charger , ev charger home , portable double telescopic ladder , 3 ph variac , rotary hammer drill 1 ph , lcr meter

CTN :45322644

01 Jun, 2026 8.70 Lacs

Sawai Madhopur - Rajasthan

Tender For supply, installation, testing and commissioning of phase wire and street light and vairious electrical equipment needed for implementation of budget announcement 2025-26 - providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with uv stabilized pc (uv stablization report submitted for uv cover ) /toughened glass cover and secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm/ wt and potted driver & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driver efficiency >85% ,thd(i) 70 and cct 5700k +355k. surge protection shall be min 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in, led street light fixture with minimum lumen output 5600 lm, sitc of ip-42 and general construction confirming to is:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-(a)thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided(b)complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam/ neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.[c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra )(d)wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap-offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.(e)all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be point to point (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.(f)floor mounted panel sh

CTN :45345533

15 Jun, 2026 10.15 Lacs

Lalpur - Gujarat

Tender For supply of bending machine conduit pipe , bus bar with brackets 1 mtr , cctv camera kit , ceiling fan coil winding machine , conduit pipe cutting and threading machines , control panel , digital multi meter , discrete component trainer , dmx controller 512 , ev charger home 1 phase input , ev charger 3 phase input , file half round 2nd cut 250 mm with handle , file round 2nd cut 150 mm with handle , knife switch dpdt fitted with fuse terminals 16 amp , knife switch tpdt fitted with fuse terminals 16 amp , ladder - tower 3 meters on tyre wheels - min 10ft - max. 30ft , lux meter lcd read out 0.05 to 7000 lumens with battery. , magnetic flux meter , mallet barwood , meter reading instrument mri , potential transformer 415 v, 50hz, pt ratio, 440v.110v,10va , power factor meter digital , primary current injection set , rcc pole with accessories , rechargeable battery 12v,100ah , rubber mat , single phase transformer , single phase variable auto transformer , smart meter 3 phase - smart energy meter , soft starter , solar dc pump 1 hp , solar panel with battery 18 watt , solar street light , solar traffic light , solid state solar base single phase energy meter , spanner d.e. set , tachometer analog type - 10000 rpm , three phase transformer , wheat stone bridge ) /bid number : gem/2026/b/7576252 * /dated: 27-05-2026 & & / bid document 1 / 40

State Government

CTN :45275642

02 Jun, 2026 3.07 Lacs

Serampore - West Bengal

Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging

State Government

CTN :45243396

29 May, 2026 23.40 Lacs

Jaipur - Rajasthan

Tender For nit 107 work of providing, fixing and installing of automatic power factor control panel (apfc) for the period of 5 years under the jurisdiction of executive engineer, phed division paota

Central Government/Public Sector

CTN :45189157

03 Jun, 2026 1.77 Lacs

Vadodara - Gujarat

Tender For service and repair of automatic power factor correction (apfc) panel installed at electrical sub-station, cws vadodara by oem

corporations/Associations/Others

CTN :45245823

25 May, 2026 NA

Surat - Gujarat

Tender For supply of different type of electrical material for maintenance purpose at various muni. building of north zone (katargam)-tube light and accessories 4 ft. (1200 mm) tube fitting including 36/40 watt electronic ballast without tube rod only fixture , 4 ft. (1200 mm) tube light rod, light output 2450 lumens. , 4 ft. 18/20 watt led complete pvc t5 tube light lumen output , 2000/2100, luminary efficiency 100lm/watt , 2 ft. 08/10 watt t5 led complete pvc tube light lumen output , 800/1000, , 4 ft. 18/20 watt led complete aluminum body t5 tube light lumen , output 2000/2100, luminary efficiency 100lm/watt , 2 ft. 08/10 watt t5 led complete aluminum body tube light lumen , output 800/1000, , 4 ft. (1200 mm) tube fitting without led tube rod only fixture with , rotating type side holder , 4 ft. led t5 tube light rod, glass type 18/20 watt lumen out 2100, 1200 , mm luminary efficiacy 100lm/watt , 36 watt electronic ballast (choke) , tube light side holder simple , led tube light side holder (rotating type ) , lamp & halogen tube , light & accessories , 2.0 x 2.0 feet square 36/40 (watt) led fixture for indoor lighting or its , equivalent , 2.0 x 2.0 feet square 36/40 (watt) led fixture driver for indoor lighting or , its equivalent , 18/20 watt, led panel light (square/round), 1700 lumens , 20/24 led panel light size 1 x 1 inch , 12/15w led panel light (square/round), 1020 lumens , 50-55 watt led flood light fitting having efficacy 100lm/watt, cct 5000 k to , 5700k , 30-35 watt led flood light fitting having efficacy 100lm/watt, cct 5000 k to , 5700k , 120 watt led flood light fitting having efficacy 100lm/watt, cct 5000 k to , 5700k , led strip light & driver , celling fan & accessories , supply of 1200 mm sweep (48''),bee 5 star rated, ceiling fan with brush less , direct current (bldc)permanent territe magnet motor, class of insulation: b, , rust free 3 nos. aluminum blades,2 nos, canopies , shackle kit with earthing , provision, 22 guage copper winding, power factor not < 0.9, service value , cmm/w) minimum 6.85, air delivery minimum 215 cmm, 305 rpm , ceiling fan,(48''),1200 mm, energy efficient ,bee 1 star rated, high speed air , delivery ,minimum 218 cmm input power maximum 53 w , pedestal fan a.c. 230 v. 50 cy/s. 400 mm sweep oscillanting ,type and , adjustable ,height complete with guard regulator, & standard lead fleixble , wires and plug top 110 watt. , supplying & erecting single phase industrial pedestal fan suitable for , medium duty ring mounted low noise operation suitable for medium duty , having 450 mm dia size and maximum speed 1440 rpm 0.80 a,80 watt. , wall fan a.c. 230 v. 50 cy/s. 400 mm sweep oscillating ,type and adjustable , height complete with guard regulator, & standard lead flexible wires and plug , top , wall fan a.c. 230 v. 50 cy/s. 450 mm sweep oscillating ,type and adjustable , height complete with guard regulator, & standard lead flexible wires and plug , top , supplying & erecting single phase approved make industrial wall fan , suitable for medium duty ring mounted low noise operation suitable for , medium duty having 600 mm dia size and maximum speed 1440 rpm 0.80 , a,180 watt. , supplying & erecting single phase approved make industrial exhaust fan , suitable for medium duty ring mounted low noise operation suitable for , medium duty having 300 mm dia size and maximum speed 1350 rpm , supplying & erecting single phase apporved make industrial exhaust fan , suitable for medium duty ring mounted low noise operation suitable for , medium duty having 225 mm dia size and maximum speed 1370 rpm , supplying & erecting approved make low noise decorative exhaust fan , having square frame abs body with inbuilt lowers & square frame, having , 150 mm with 1350 rpm , supplying & erecting approved make low noise decorative exhaust fan , having square frame abs body with inbuilt lowers & square frame, having , 200 mm with 1350 rpm , supplying & erec

Central Government/Public Sector

CTN :45241980

21 May, 2026 NA

Ernakulam - Kerala

Tender For battery charging and discharging panel: supply and commissioning of digital signal processing (dsp) controlled igbt based ac to dc rectification (converter) with active power factor correction with finecontrol on voltage regulation, ripple, thd and improved efficiency with re-generative feature suitable to provide float charging and boost charging of ni-cd batteries of 199 ah/110 v capacity & lead acid batteries of 75 ah/110 v capacity as per specification no. c/e/els/ers/spec/06 attached. all meters and gauges to have valid calibration certificate from nabl approved lab. [ warranty period: 30 months after the date of delivery] ]

Central Government/Public Sector

CTN :45141051

21 May, 2026 NA

Ernakulam - Kerala

Tender For corrigendum : battery charging and discharging panel: supply and commissioning of digital signal processing (dsp) controlled igbt based ac to dc rectification (converter) with active power factor correction with finecontrol on voltage regulation, ripple, thd and improved efficiency with re-generative feature suitable to provide float charging and boost charging of ni-cd batteries of 199 ah/110 v capacity & lead acid batteries of 75 ah/110 v capacity as per specification no. c/e/els/ers/spec/06 attached. all meters and gauges to have valid calibration certificate from nabl approved lab. [ warranty period: 30 months after the date of delivery ]

Road Light Panel Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

Central Government/Public Sector

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector