Latest rocker shaft Tenders | Government rocker shaft Tenders

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

CTN :45675367

09 Jul, 2026 NA

Multi City - Jharkhand

Tender For auction sale of others - 1 v-belt a-40 06 nos. 2 v-belt a-42 02 nos. 3 v-belt a-49 18 nos. 4 v-belt a-59 02 nos. 5 rocker shaft with core plug 06 nos 6 copper joint 0.8 mm 11 nos 7 gasket for cummins make 08 nos 8 spring for valve kirloskar ra6 12 nos 9 bushing camshaft -2-7 03 nos 10 gasket wir out let cummins make 02 nos 11 banjo bolt 09 nos 12 banjo bolt for gear casing 04 nos 13 spacer 06 nos 14 retain fuel conn . gasket 40 nos 15 cut out 04 nos 16 gasket injfuel conn 28 nos 17 gasket 04 nos 18 screen oil pan 05 nos 19 lock 30 nos 20 cyl head gasket set 04 nos 21 hose 06 nos 22 hose 34 nos 23 hour meter 01 nos 24 piston complete rc-3 10 nos 25 ring 56 nos 26 connecting rod assembly 08 nos 27 cup for valve rn ¿ 6 06 nos 28 washer 03 nos 29 cylinder liner 06 nos 30 fuel pump coupler 01 nos 31 ball bearing double row 04 nos 32 dowel for connecting rod ra 6 12 nos 33 bushing 06 nos 34 liner ¿o¿ ring 02 nos 35 nut 78 nos 36 hose 03 nos 37 retainer coler & ring 12 nos 38 copper joint 0.5 mm 07 nos 39 guide valve stem 23 nos 40 rubber bush top size 08 nos 41 carbon bush m145 e 09 nos 42 rubber bush small size rc 8 06 nos 43 thermostat seal for kcl 08 nos 44 push rod 08 nos 45 copper joint 1.0mm 11 nos 46 stud for cy.head/short 12 nos 47 big end bearing 24 nos 48 stud for cyl head [long] ra-6 12 nos 49 joint for l.0 sump ra ¿ 6 02 nos 50 fuel injection pipe 01 nos 51 fuel filter element kcl 31 nos 52 relief valve 04 nos 53 starter [ c12 volts] 02 nos 54 starter with steel 01 nos 55 supply manifold assembly 02 nos 56 lock washer ra-6 12 nos 57 collects v[pair] for valve ra-6 12 nos 58 bush rubber bottom 06 nos 59 lock washer ra-6 12 nos 60 main bearing 0.20 u/s ra-6 14 nos 61 spring ra-6 12 nos 62 oil seal n.t.fwe ra-6 02 nos 63 joint for ra-6 10 nos 64 push rod tube 08 nos 65 joint for support ra-6 02 nos 66 l.o.pump complete ra-4/ra-6 01 nos 67 push rod ra-6 12 nos 68 core plug 04 nos 69 v.r lever with bush 12 nos 70 cap for rubber bush 08 nos 71 many fold fuel drain 02 nos 72 joint for pump 04 nos 73 fuel pipe pump to filter 03 nos 74 complete set of joints 02 nos 75 injector complete 06 nos 76 connecting rod 06 nos 77 cy lender liner 01 nos 78 piston ring oho c/s 12 nos 79 hose 13 nos 80 hose 01 nos 81 valve spring 24 nos 82 diesel filter 18 nos 83 connecting rod bearing 12 nos 84 l.f.bearing 10u/s 05 nos 85 main bearing bush ruston 02 nos 86 small end bush 06 nos 87 main bearing seal ruston 01 nos 88 valve guide ruston 04 nos 89 thrust washer 06 nos 90 piston assly [std] 11 nos 91 reliet valve assly 02 nos 92 oil seal ruston 02 nos 93 banjo bolt with tail 03 nos 94 exhaust silencer 02 nos 95 filter dise 12 nos 96 adaptor for filtr 03 nos 97 washer connecting rod 12 nos 98 main bearing narrow 10u/s 06 nos 99 connecting rod 20 nos 100 main bearing wide 20u/s 05 nos 101 joint 04 nos 102 gasket 07 nos 103 v belt a/57 01 nos 104 piston ring 02 nos 105 corrosion register 01 nos 106 banjo bolt belt 08 nos 107 guide for valve 06 nos 108 bushing gear cover 04 nos 109 piston ring 18 nos 110 cir clip ra-6 12 nos 111 piston pin ra-6 06 nos 112 fuel filter elements (pre) 18 nos 113 fuel filter elements (micro) 19 nos 114 expansion bellow of outlet 02 nos 115 banjo bolt (hallow bolt) 01 nos 116 banjo bolt 01 nos 117 copper washer 12 nos

corporations/Associations/Others

CTN :45648129

03 Jul, 2026 NA

Puruliya - West Bengal

Tender For tender for supply of soot blower spares for rtps dvc steam nozzle tube for aph shoot blower model no.:, ahlw, tag no. ah03 &ah04 part #08136lw-007, contract no. sc08136- shanghai clyde bergemann, gear box for aph shoot blower model no.: ahlw, tag nos. ah03 & ah04 part # gb_ahlw, contract no. sc08136-shanghai clyde bergemann, chain pno-gb1243.1, roller shaft pn-ahlw/8/13, vent valve assly, all type soot blower (ps-, ll, v04, ahlw), part no-6518, gasket, vent valve for short retracting blower, model no.: v04, part # 1659, contract no. sc08136-, shanghai clyde bergemann, spring, vent valve, all type soot blower (ps-ll, v04, ahlw), part no-5304, screw tube assly (shaft assly), wall deslagger, model: v04, part no-v04-2-0, nut drive, machined, wall deslagger, model: v04, part no: v04-2-2, pin screw assly, wall deslagger, model: v04, part no: 5044, roller chain assly, wall deslagger, model: v04, part no: v04-3-4, packing of feed tube, wall deslagger, model: v04, part no: 6638, gasket of feed tube assly, wall deslagger, model: v04, part no: v04-5-3, poppet valve assly, inlet d55, all type soot blower (ps-ll, v04,ahlw), part no-25844, valve internal assly, inlet d55, all type soot blower (ps-ll, v04,ahlw), part no-7048, chain link cranked, long retract soot blower, model:ps-ll, part no-5640, chain link, long retract soot blower, model:ps-ll,part no-5648, chain, long retract soot blower, model:ps-ll, part no-1823, packing (hard), long retract soot blower, model:ps-ll, part no-13750, packing (soft), long retract soot blower, model:ps-ll,part no-5629, feed tube gasket, long retract soot blower, model:ps ll, part no-1668, lance tube gasket, long retract soot blower, model:ps-ll, part no-1678, spring-valve, valve intnl assly, feed tube assly, long retract soot blower, model:ps-ll, part no-08136ll-001, lance tube assly, t91,101.6 od(tag no.r1, r2, l1&l2), long retract soot blower, model:ps-ll, part no-08136ll-002, lance tube assly, t11, 101.6 od (tag no.r3 to r5,l3 to 15), long retract soot blower, model: ps-ll, part no-08136ll-003, lance tube assly, t11 (tag no.r11 tor22 &l11to l22), long retract soot blower, model:ps-ll, part no-08136ll-005, lance tube assly, t11(tag no. r6 to r10 &l6 to l10), long retract soot blower, model: ps-ll, part no-08136ll-004, lever / roller for limit switch make - clyde bergemann, part id: v04-11-5

CTN :45640870

06 Jul, 2026 NA

Doiwala - Uttarakhand

Tender For spare repair and overhauling of sugar stacker - needle g.b.250 (long size) , needle bar guard, , looper, , looper thread cast of hook assembly, , needle bar with nut, , looper ball joint assembly, , needle bar connecting link, , feed bar, , feed drive eccentric assembly, , stitch regulating stud assembly, , feed bar shaft, , throat plate, , bush set, , threat tension assembly complete, , feed dog, , feed rocker assembly, , screw set, , feed lift eccentric fork, , feed lift eccentric fork assembly, , looper avoid eccentric assembly, needle bar connection, , crank connecting rod, , needle bar connecting assembly, , needle bar clamp nut, , looper shaft, , looper rocker assembly, , collar for feed rocker, , pressure bar(left), , pressure bar(right), , pressure foot, , guide fork, , looper drive lever, , shell for crank shaft, , needle lever ball link, , needle lever, , looper drive connecting assembly, , main crank shaft assembly, , ball bearing for main crank shaft, frame thread guide, , needle lever shaft, , looper drive lever shaft, , pressure bar collar, , driving pully for stitching head, , bearing housing, , bolt for driving pully, , feed rocker shaft, , pressure bar regulator, , thread eylet, , cover set(aluminium), , looper stud complete holder, , shaft for looper rocker stud, , take up complete assembly, , looper shaft fork, , needle lever bolt

CTN :45577473

02 Jul, 2026 3.50 Lacs

Muzaffarnagar - Uttar Pradesh

Tender For supply of on conversion basis gun metal bearing liner for transmission gear shaft bottom bearing bor 305 mm halve complete in all respect finish machine , on conversion basis gun metal bearing for top roller top halve complete in all respect finish machined , on conversion basis gun metal bearing liner for side roller halve complete in all respect finish machined , on conversion basis gun metal bearing liner for side roller halve complete in all respect finish machined. , on conversion basis gun metal bearing liner for transmission gear shaft-bottom bearing bor 250 mm halve complete in all respect finish machine

Central Government/Public Sector

CTN :45543410

25 Jun, 2026 NA

Bardhaman - West Bengal

Tender For corrigendum : shaft -cross pusher rocker shaft

Central Government/Public Sector

CTN :45597071

08 Jul, 2026 NA

Abohar - Punjab

Tender For supply of assy clutch disc , assy clutch cover , clutch release bearing , assy pivot bush front suspension lower arm , assy pivot bush front suspension upper arm , assy ball joint lower , assy ball joint upper , circlip assy ball joint lower , rubber bush front antiroll bar , bush shock observer front , kit gear shifter complete , brake shoe 1st over size rear , wheel mounting nut and bolt , ball joint outer thread outer lh and rh , base plate gs lever top bellow , belt power steering , belt alternator , belt compressor , assy fuel filter , assy fuel filter primary , wd40 rust cleaner , rubber bellow gs lever , master switch power window , door switch power window front lh , motor power window with panel and lifter complete assy rear rh , tail lamp assy rear lh , fog lamp assy with bulb for bumper , side body indicator , reservoir windshield washer and front and rear motor with o ring , bulb capsule type 12v , bulb tube type for cabin light 12v , lt wire 4mm , pull push switch , auto paint as per sample , matt finish black , auto paint silver , clear kit auto , thinner auto , polyester putty , nc putty , putti plate , masking tape , primer auto gray , 2 inch reflector tape white , 2 inch reflector tape red , door lock left front assy , door lock outer handle , foot cover plastic as per sample , glass channel rubber beading , gi coated sheet 8feet x 4feet 20 guage , ms sheet 2feet x 2feet 14 gauge , bolt with washer no 13 as per sample , white silicon tube , rear step accessory , steering mounting cross member , fuel tank cover , gasket cylinder head , gasket cylinder head cover , gasket intake mainifold , gasket exhaust mainifold , o ring came sensor case , o ring water intake , gasket thortool body , gasket oil seal housing rear , gasket oil pump , gasket water pump , o ring spark plug , oil filter assymbly , pistion with gugen pin and lock , piston ring , bigin bearing , main bearing , thrust washer , oil stainner o ring , oil seal front , oil seal rear , bearing input shaft , oil pump assymbly , shaft rocker arm , o ring rocker shaft , seal valve stem , valve intake , valve exhaust , clump rocker arm , spark plug , timing belt , tenssionar timing belt , cover assymbly clutch , disc clutch , bearing clutch relies , engine mounting front , thormstate valve , air filter element , fuel pump assembaly , belt water pump , valve grinding stic small , three annanabond tube 100 gms //bid details 2 / 69

CTN :45332546

23 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of eprom mpu24/mem5-02 programmed , panel rcs-fpp/04 , corrosion inhibitor rust ban 326 , snap ring 32x1.5 din 471 , computer accessories , plug-in board , screw m10x150 , gasket , pressure gauge 0-10 bar , temperature monitor , instrument , o ring 39.2x3 , plug-in board , telephone cable , thermocouple , adjusting washer , soldering iron stand , woodruff key , o ring , actuator vlv , cylinder head with valve , paste ultra therm mtu , pressure hose , oil filter , o ring , molykote paste g-n plus , gasket liquid loctite 573 , clamp , terminal , plug in board cob9-01/a , pressure sensor , relay 24v / 4a , conversion kit f/series 4000 (5205304531) , illuminescent diode , signal lamp , mpc1-01 card f/computer a.741620/741634 , software , tool bag , module cob 8-01 , diskette , housing , temperature sensor pt100/110mm , plug-in board , male connector , speed sensor , plug-in board sab 1-03(5295308912) , coolant level sensor , flashing lamp red , plug-in board cib 3-02 , plug-in-board not adjusted , speed transmitter dm52 , pressure sensor 1600 bar/r , relay , terminal , pressure sensor , flashing light , blue , fuse fk2/6a , terminal(0055314981) , terminal strip_0045310081 , fuse 2a fk2 , pressure sensor , switch , terminal block , pressure sensor 6 bar(sw) , fuel filter primary(lcm) , plug , w/p repair kit , relay , printer , thermal actuator , plug in board dfc 2-01 , display unlabelled , connection interface for monitoring , cable for monitor system , switch , loctite nr 510 surface sealant , plug , union , bolt m20 1.50x103.0 lg 18 conrod , switch , plate guard g73 , switch , bushing , bushing , modular system , led , conn fuel rail rear , diode m.kuelkoerp , plug in board mpu 30-02 , track-ball , cable , plug-in board , cover , automatic cutout , multi led 5 5k blue , plug in board , male connector , control lever ros 2 03 , fuse , control lever , o-ring , plug - in board , nut , sealing ring , keyboard english , terminal , wiring harness to injector , mpc 1 01 card f computer , silcone rubber loctite 5970 , compensating washer , plug-in board , switch , washer , shaft wtr pmp hi temp clg circuit , guide ring , valve keeper wedge , plug-in board , plate , flow restrictor , plug-in-board , plug in board , filter element , adaptor , modular system , plug-in board rob1-01 a , inb 1 , trackball , plug-in board , plug in board aib2-03 , aib 1 , plug-in board , plug-in-board , roller tappet , con rod bearing size 0-0 , pressure sensor , plug-in board , sealing ring , plug in board , bellows , transition socket , sleeve rubber , grommet , ring sealing a12x15.5 , hex nut , straight connector , rocker shaft , techometer , computer hard disc 2.5 60gb not adjuste , screw , eprom mem5 mcupps cps adjusted , audiable alarm , adaptor 10 6 n 15007 , plug , pressure spring , o ring , benjo screw , washer , o ring , plug in board , plugin board , washer , grommet , o ring , plug , drain valve , plug-in-board not adjusted , piston ring , washer , o ring , rtv , cover , split pin , level monitor bediaplca , terminal strip , contact block , module mcs 5 pim3 , oil seal high temp cirt pump , panel , repair kit , starter , bearing bushing , seal ring , circlip , seal ring , ring asm , contam indicator , fuel filter , pressure sensor , plug-in board

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

Co-operative

CTN :45474707

23 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For c.i. item on conversion/supply basis - c.i.pipe with standard thickness & flange as per i.s.i. specification machined from dia 4" to 12"(i) new material supply basis, (ii) on conversion basis, c.i. bend, duck foot bend, cross,tee and other such part all size as per drg.(i) new material supply basis, (ii) on conversion basis, c.i.drum, rod,bush, bari,idler pully, break drum for cane unloader etc as per drg.(i) new material supply basis, (ii) on conversion basis, c.i.coupling from 4"dia to 10"dia plane/flange type(i) new material supply basis, (ii) on conversion basis, c.i. firing frame,door side chamber, bagasse rotary chuts, rotary feeder drum , clit, hanger, beam, gutka, furnace nozzle, clam etc. and other such parts for lipi/taxmaco boiler as per different drg.high chrome grade 25 , casting & machined temp. capacity 15000 c(i) new material supply basis, (ii) on conversion basis, c.i. clamp/ hanger clit small size for lippi boiler no. 3 as per drg. blr-79 high chrome grade 25 , casting & machined temp. capacity 15000 c, c.i scapper mixed with pig iron and having standard hardness dully machined as per drg.no.mh-66 ( r)(i) new material supply basis, (ii) on conversion basis, (iii) grooving of c.i.scrapper as per drg., centrifused casted c.i.coupling for fmg gear of kcp mill od 1000 mm.pcd 815(18 holes)9+9,with machining complete as per drg.no.mh-93, c.i.motor cover for different type motor, mill setting bolt & nut for kcp mill drg.no.mh-106, mill setting bolt & nut for taxmaco mill drg.no.mh-38, c.i.worm and worm wheel for crystilizer as per drg.bh-39 ( r ) machined, c.i.worm and worm wheel for vertical crystilizer no. 2 complete set as per drg. machined, eccentric shaft and eccentric for hopper as per drg.no.bh-60, m.s.shell for under feed roller as per drg.mh-95.length 1525 mm.od 750mm,thickness 18mm, c.i. muff coupling for cane unloader as per drg.no cu-25, c.i.gear for magma mixture as per drg.no bh-137.od 450mm,no.of teeth-51.bore 70mm, width 63mm, c.i.brake drum for s.d.centrifugal machine taxmaco make duly machined(i) as per drg.no. bh 81/1, (ii) as per drg.no bh-81/2, c.i.v-belt pully of cont.centrifugal machine duly machined, c.i.scale seat for juice weighing scale duly machined and drilled as per drg.no.mh-195, id fan pully (as per drawing no. bl-r-128/2024-25), id fan motor pully (as per drawing no. bl-r-129/2024-25), boiler grate bar material-cont iron. (as per sample/drg.), boiler furnace manage gap bar. (ap per sample/drg.), chief engineer

Rocker Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector

Co-operative