Tender For supply and installation of open gym equipments under mplads funds for various locations of parks in municipal corporation of delhi - supply & installation of open gym equipments under mplads funds for various locations of parks in municipal corporation of delhi, seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size), seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for a
Tender For supply of set of labyrinth and bearing cap (de) for wap-7/wag-9 traction motor type 6 fra6068. set consisting of 4 items 4 nos. as per clw's spec. no.- 4tms.096.068 (rev.-2) (alt.-1). detail s of item are as follows:- (i) inner labyrinth de as per clw's drg. no.- 4twd.096.043 (alt.-7) qty.= 01 n o. (ii) outer bearing cap de as per clw's drg. no.- 1twd.096.006 (alt.-8) qty.= 01 no. (iii) inner labyri nth de as per clw's drg. no.- 4twd.096.028 (alt.-6) qty.= 01 no. (iv) outer labyrinth de as per clw's drg. no.- 4twd.096.029 (alt.-8) qty.= 01 no. [ warranty period: 30 months after the date of delivery ]
Tender For supply of dg set spares - valve cup , valvespring , valve tappet , washer , screw adjt (rkr) , push rod , bush for injector , bolt for mb cap (hex head) m14x2x128 , oil seal (115x140x16) , oil seal , bolt , washer , special banjo bolt (lo supply to pump) , bolt for fly wheel , washer for sump screw , valve sealed , copper washer inj , cylinder liner , injector yoke , drain plug with magnet & o ring , thrust washer , worm drive clamp (29-45 mm dia) , washer fip gear , thermostat element , primary element , secondary element , fuel piep inlet m16x1.5 , v belt cogged (bx-48) , radiator cap (koel 6r1080ta) , thrust washer cam shaft , cyl head bolt , v belt (xpa 1250) cogged , hose thermostat , banjo bolt for piston cooling nozzle , rubber hose turbocharger , piston assy , valve inlet , composite washer for banjo bolt , set bolt for front cover , set screw , sump screw , bolt for ex manifold , set bolt , dowel , banjo bolt for noz hol , banjo bolt , washerplain , copper washer , radiator hose clip (22mm) , worm drive hose clip , spring dowell pin cylinder block , raditor hose clip (35 mm) , set bolt , washer , piston cooling nozzle assy , camshaft gear assy , gasket cyl head 6r1080 ta , pipe rkr arm , lub oil cooler assy , hose for water pipe , fuel pipe (feed pump to filter) , lp pump assy , vent pipe for radiator , set of joints , set of o ring , fuel pipe (fuel filter to fuel pump) , leak off pipe , breather hose for 125 kva silent set , hose for air cleaner , set of washer , set of hoses , fuel pipe filter to pump , fuel pipe feed pump to filter , gasket for sump , le bearing set , kir 6rta c/r brd std (04692020) , centrfugal filter , compression ring , indicator air cleaner , air cleaner element (koel 6r 1080 ta,100 kva) , compression ring turbo outlet connection , t bolt clamp for tc (100-108 mm dia) , cam bush (koel 6r 1080 ta) , bearing main kir 6r1080std , thrust washer set of inner & outer pairs
Tender For corrigendum : supply of - spares for bhel make critical ht motors at cpp terminal box cover 400kw,fr:1la7566-2p, terminal connector 400kw,fr:1la7566-2p, motor cooling fan 400kw,frame:1la7566-2p, motor fan cover 400kw,frame: 1la7566-2p, brg temp detector 400kw,frame:1la7566-2p, bearing housing set 400kw,fr:1la7566-2p, de outer brg cap,400kw,6.6kv,40096a-401-, end shield set,400kw,6.6kv,40096a40121-8, terminal box cover 385kw,fr:1la7566-2p, terminal connector 385kw,fr:1la7566-2p, motor cooling fan 385kw,frame:1la7566-2p, motor fan cover 385kw,frame:1la7566-2p, mtr btd 385kw,fr:1la7566-2p,bhel, bearing housing 385kw,frame:1la7566-2p, outer brg cap,385kw,6.6kv,40096a40131-7, end shield set,385kw,6.6kv,40096a40131-8, mtr tb cvr 600kw,frame:1la7632-4,bhel, motor cooling fan 600kw,frame:1la7632-4, motor fan cover 600kw,frame:1la7632-4, brg housng 600kw,frame:1la7632-4,bhel, mtr brgcap 600kw,frame:1la7632-4,bhel, mtr es set 600kw,frame:1la7632-4,bhel, motor tb cover 2100kw,frame:1rn7632-4p, term connector 2100kw,fr:1rn7632-4p,bhel, motor fan 2100kw,frame:1rn7632-4p,bhel, motor fan cover 2100kw,frame:1rn7632-4p, motor btds de+nde 2100kw,fr:1rn7632-4p, bearing house 2100kw,fr:1rn7632-4p,bhel, bearing cap set 2100kw,frame:1rn7632-4p, end shield set 2100kw,frame:1rn7632-4p, mtr ex gkt,2.1mw,6.6kv,s.n:40096a40111-9, motor tb cover 225kw,frame:1la7502-2p, motor ter connector 225kw,fr:1la7502-2p, motor fan 225kw,frame:1la7502-2p,bhel, motor fan cover 225kw,frame:1la7502-2p, motor btd 225kw,frame:1la7502-2p,bhel, bearing housing 225kw,fr:1la750-2p,bhel, bearing cap 225kw,frame:1la7502-2p,bhel, end shield set 225kw,fr:1la7502-2p,bhel, motor tb covr 855kw,frame:1la7714-2,bhel, motor cooling fan 855kw,frame:1la7714-2, motor fan cover 855kw,frame: 1la7714-2, bearing temp detector 855kw,fr:1la7714-2, end shield set 855kw,fr:1la7714-2,bhel, t. box cover 4100kw,frame:1rn7716-4,bhel, motor cooling fan 4100kw,frame:1rn7716-4, motor fan cover 4100kw,frame:1rn7716-4, brg temp detector 4100kw,fr:1rn7716-4, end shield set 4100kw,frame:1rn7716-4, heat excr gskt set 4100kw,fr:1rn7716-4, mtr tb cvr,800kw,frame:1la7712-6,bhel, mtr tml cn 800kw,frame:1la7712-6,bhel, motor cooling fan 800kw,frame:1la7712-6, motor fan cover 800kw,frame:1la7712-6, mtr btd 800kw,frame:1la7712-6,bhel, brg housng 800kw,frame:1la7712-6,bhel, mtr brgcap 800kw,frame:1la7712-6,bhel, mtr es set 800kw,frame:1la7712-6,bhel, t.box cover 3050kw,frame:1la7905-4,bhel, terminal connector 3050kw,fr:1la7905-4, motor cooling fan 3050kw,frame:1la7905-4, motor fan cover 3050kw,frame:1la7905-4, brg temp. detector 3050kw,fr:1la7905-4, motor brg hsg set 3050kw,fr:1la7905-4, motor end shield set 3050kw,fr:1la7905-4, motor outer brg cap set 3050kw,1la7905-4, motor nde side sleeve brg assy 855kw, mtr de brg sleeve assy 855kw,1la7714-2, - quantity | 1 - msme exemption | no - startup exemption | no