Latest rotor set Tenders | Government rotor set Tenders

CTN :45541202

23 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For purchase of tanche - lab equipments for eee and ece department - purchase - lab equipments for eee department electronics lab, single phase to single phase cyclo converter kit single-phase bridge cycloconverter power devices: scr/triac based input supply: 230 v ac, 50 hz step-down isolation transformer 230 v / 12 v output: 12 15 v ac, frequency: 0 25 hz (adjustable),firing angle control circuit and frequency control circuit to be provided built-in resistive load, terminals to be brought on ms panel with necessary symbols and circuits, pwm based step down dc chopper using mosfet/igbt kitpwm based step-down dc chopper (buck converter) power device : power mosfet / igbt based switching circuit input supply : 24 v dc to 110 v dc or derived from 230 v ac mains through rectifier unit output voltage :(0 to vin) variable dc output current : up to 5 a dc maximum with suitable load resistor (r load) pwm duty cycle control provided pwm generation and control circuit inbuilt gate driver circuit provided, single phase single pulse / sinusoidal pwm inverter using mosfet/igbt kittype : single phase pwm inverter trainer power device : mosfet / igbt based inverter circuit input supply : 12 24 v dc output voltage : 30 v rms ac output phase : single phase output frequency : 0 50 hz variable output power : 100 w single pulse pwm operation sinusoidal pwm (spwm) operation variable frequency control pwm generation and firing control circuit inbuilt gate driver circuit provided test points provided for waveform observation and analysis built-in resistive load provision, on / off control of lamp using solid state relay kittype : solid state relay (ssr) trainer kit control/input voltage : 12 v / 24 v dc or up to 30 v dc output load voltage : 230 v ac, single phase load control : on/off control of ac lamp load solid state relay based switching circuit opto-isolated input control built-in ac lamp load manual on/off switching arrangement led indication for input and output status, speed control of ac motor using vfd drive module with ac motortype : variable frequency drive (vfd) module input supply : 415 v ac, three phase, 50 hz output : three phase variable voltage and variable frequency ac output 1 hpthree phase squirrel cage induction motor415 v ac 50 hz &1440 rpm control technique : pwm / spwm based control frequency range : 0 50 hz variable digital display for frequency and operating parameters start / stop and forward / reverse control, acceleration and deceleration control facility powder coated ms control panel tabletop / floor mounted laboratory type setup clearly labelled circuit diagram and control switches proper insulated terminals and earthing arrangement, purchase - lab equipments for eee department electrical machines lab, three phase transformertype: three phase transformer, rating: 3 kva input voltage: 415 v ac, 3-phase, output voltage: 230 v ac, 3-phase frequency: 50 hz winding material: copper wound insulation class: class b or higher duty: continuous duty suitable for laboratory usebench/floor, dc stepper motor drive kit with stepper motorinput supply : 230 v ac, 50 hz stepper motor : permanent magnet / hybrid type with suitable driver circuits. motor operating voltage : 12 24 v dc variable speed control forward and reverse direction control full step and half step operation manual / automatic pulse generation facility built-in regulated dc power supply led indication for phase sequence and status test points provided for waveform observation start / stop control switches to be provided overload and short circuit protection to be provided mounted on compact powder coated cabinet with printed circuit diagram proper insulated terminals and interconnecting leads to be provided patch chords for interconnection., dc servo motor drive kit with servo motorinput supply : 230 v ac, 50 hz servo motor type : dc servo motor with feedback arrangement motor operating voltage : 12 24 v dc controller type : microcontroller based servo drive contr

CTN :45512690

02 Jul, 2026 4.28 Crore

Visakhapatnam - Andhra Pradesh

Tender For supply of 25vkpc006 c c - brush bracket assembly for 19 kw motor , fan , sw temp gauges , sight glass part no. 06001 avail.as com.as.kit-item-209 , set shut-off valve nw38 part no. 08398 , set of gaskets for condenser 20tr ac plant for ekm submarine , tube for evaporator for 20 tr ac plant for ekm submarine , 3 way isolation valve for pressure gauges , refrigerant piping fittings 20tr ac plant for ekm submarine , rear outer bearing cover , sw pressure gauges , temperature gauge 100 dial -30 to 50 deg c , starter cum control panel for20tr ac plant for ekm submarine , terminal connectors with din rail 35 wago 6 sq mm 282-101 , synthetic ref oil savsyn2068 , gasket cover window he side , gasket cover window filter side , gasket cover top hsg dist. block , gasket cover top hsg manifold block , nut hex m24x3 , bolt hex std m20x2.5x120l , fan , compressor discharge temp gauge , compressor suction temp gauge , mccb merlin gerin 160 a 4 pole ns160n 4p30640 coil 24v dc , starter card elmot for 45 kw dc panel , terminal block for 5.5 kw motor , core for filter drier , rubber bellows for sw pump discharge , rubber bellows for sw pump suction , shaft for sw pump , mechanical seal for sw pump , pressure gauge 65 dial -1 to 15 kg-cm2 for r134a , oil seperator danfoss oub 4 for 2 x 2.1 tr ref plant , sea water pump be pump a3610m for 2 x 2.1 tr ref plant , solenoid valve danfoss evrs3-24 vdc coil , thermo exp valve sporian w je-80 jc charge 1-5-8x1-5-8inch ods , rotor setl/d 1.45 part no. n0900408030 , metaflex coupling for compressor for 144 tr ac plant , valve check type 125 nb wafer type , core for filter drier sporian rc10098 , thermostatic expansion valve danfoss teat 85-33 , shock mount irmra akcc-400e , valve plate assembly part no-08436 , set shaft seal part no 08008 , set oil pump part no 08044 , set piston dia 70 part no 08035 , set gaskets part no 08072 , set connecting rod part no 08307 , set oilsump heat 80w 220-240v part no 08425 , set capacity regulator 24 v dc , set of v belts , oil separator danfoss oub 4 for 2 x 2.1 tr refrigeration pla , valve angle type 1-2inchntp(m) x 1-2inch flare , safety valve 1-2inchnpt m set pressure 12.5 kg-cm2 r134a , valve angle type 1-4inch ntp m x 1-4inch flare , thermostatic exp valve gfe-1-2jc charge 1-4inch x 1-2inch flare , thermostatic exp valve gfe-1.1-2jc charge 1-4inch x 1-2inch flare , vibration eliminator 5-8inch ods , vibration eliminator 1-1-8inch ods , temp switch danfoss rt34-25 to 15 deg c , hrc fuse link ge ns4 4a with nh type fuse base , control transformer tape wound 415 v/110 v 150 va , filer drier core , safety valve condenser , liquid injection solenoid valves , hex head screw m6x125l , lp-op cutout mp55r r12-r22 , horizontal shell and tube type condensor , brazed plates type direct expension r134a evaporator , safety relief valve for condensor , thermostatic expansion valve , open end spaner set , temperature transducer , compressure suction pressure gauge , compressore discharge pressure gauge , element complete with o ring , pump trailing pompe pollard type 100 pr-60-100 c-g-n , direction of control valve with manual override

Central Government And Public Sector

CTN :45494454

18 Jun, 2026 NA

Bhilai - Chhattisgarh

Tender For supply of gate drive unit dytp 155a as per m/s alstom material id no. : tc3est000229-9009, suitable for bombardier make tc & prp system of wag 9 loco. [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government / Public Sector

CTN :45439780

26 Jun, 2026 NA

Ahmedabad - Gujarat

Tender For procurement of pneumatic & mechanical spares at ahmedabad bottling plant, sanand - filter regulator lubricator 1/2" , filter regulator lubricator 0.25 inch , pu tube 4 mm , pu tube 6 mm , pu tube 8 mm , pu tube 10 mm , pu tube 12 mm , elbow fitting 4x0.25 inch , elbow fitting 6x0.25inch , elbow fitting 8x0.25 inch , elbow fitting 10x0.25 inch , elbow fitting 4x0.125 inch , elbow fitting 6x0.125 inch , elbow fitting 8x0.125 inch , elbow fitting 10x0.125 inch , elbow fitting 6x1by 2 inch , elbow fitting 8x1by2 inch , elbow fitting 10x1by2 inch , elbow fitting 6x3by8 inch , elbow fitting 8x3by8 inch , elbow fitting 10x3by8 inch , straight fitting 4x1by4 inch , straight fitting 6x1by4 inch , straight fitting 8x1by4 inch , straight fitting 10x1by4 inch , straight fitting 4x1by8 inch , straight fitting 6x1by8 inch , straight fitting 8x1by8 inch , straight fitting 10x1by8 inch , straight fitting 6x1by2 inch , straight fitting 8x1by2 inch , straight fitting 10x1by2 inch , straight fitting 6x3by8 inch , straight fitting 8x3by8 inch , straight fitting 10x3by8 inch , tee fitting 4x4x1by4 inchmm , tee fitting 6x6x1by4 inch mm , tee fitting 8x8x1by4 inch mm , tee fitting 10x10x1by4 inch mm , tee fitting 12x12x1by4 inch mm , tee fitting 4x4x1by8 inchmm , tee fitting 6x6x1by8 inch mm , tee fitting 8x8x1by8 inch mm , tee fitting 10x10x1by8 inch mm , tee fitting 4x4x4 mm , tee fitting 6x6x6 mm , tee fitting 8x8x8 mm , tee fitting 10x10x10 mm , tee fitting 12x12x12 mm , push and pull type pneumatic switch , 5/2 hand lever type pneumatic switch x , double pilot valve 5by2 x 1by4 inch , single pilot valve 5by2 x 1by4 inch , or gate 1by4 , pneumatic cylinder 50 x 450 non-magnetic , pneumatic cylinder 50 x 250 non-magnetic , pneumatic cylinder 50 x 300 non-magnetic , pneumatic cylinder 50 x 320 non-magnetic , pneumatic cylinder 63 x 80mm non-magneti , pneumatic cylinder 50 x 80 mm non-magnet , pneumatic cylinder 125 x 300 mm non-magn , pneumatic cylinder 50 x 125 mm non-magne , pneumatic cylinder 50 x 320 magnetic typ , pneumatic cylinder 50 x 500 magnetic typ , pneumatic cylinder 63 x 160 mm magnetic , quick exhaust valve 1by2 inch , quick exhaust valve 1by4 inch , quick exhaust valve 3by4 inch , pnuematic cylinder 50x300 with profile f , dnc festo 40 cylinder seal kit , smc cylinder 50 seal kit , norgren cylinder 50 seal kit , smc cylinder 63 seal kit , festo cylinder 50 seal kit , pneumatic connector 14x1/2 , pneumatic connector 12x3/8 , pneumatic connector 10x3/8 , pneumatic connector 8x3/8 , solenoid valve with 3/2 valve 24vd , solenoid valve with 5/2 valve 24vd , ss304 angle valve 1/2" , spring for self centering , baliga, has, teflon hose (600 mm) , baliga, has, hot air gun (hylum) , plumber block w/ brg, 213-65mm, conveyor , plumber block w/ brg, 212-60mm, conveyor , bearing unit, ucp-213 , bearing, pillow block, ucp 212, ntn , uhmw strip 40mmx10mmx3000mm , roller, teflon, p/n:e24-10001 , pressur gauge 0-16 kg 6 inch , pressure gauge 0-28kg, dial 6 inch , pressure gauge 0-16 kg, dial 4 inch , pin, chain, en-24, conveyor , ms 60 mm bore 32 teeth duplex gear , ms 60 mm bore 38 teeth duplex gear , duplex sprocket 65mm x 32 teeth , duplex sprocket 65mm x 34 teeth , duplex sprocket 65mm x 36 teeth , duplex sprocket 65mm x 30 teeth , duplex sprocket 58 mm x 18 teeth , duplex sprocket 58mmx 20 teeth , duplex sprocket 58 mm x 24 teeth , introduction stopper assembly , hexnipple-1/2"npt(m)to 1/2"bspt(m) , jaw coupling 110 no , jaw coupling 150 no , sprkt chain, duplex drive gear, 1inpitch , ms 2.5 mtr c channel for conveyor , ms angle for conveyor 40mm x 40mm x 6mm , lock nut 16 mm bsp thread , csk bolt 8x35 mm with nut washer , csk bolt 10x60 mm with nut washer , o ring inserter tool , shaft with key, conveyor, 60x65, length-850 , shaft for helical gear 60 mm bore length , alen bolt m6x 25 (full thread) with lock nut , alen bolt m6x 40 (full thread) with lock nut , alen bolt m8 x 25 (full thread) with lock nut , alen bolt m8 x 40 (full thread)

CTN :45420680

24 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For supply of 26vy8c901 stp c c - ee6120b-15mx sewage treatment plant model 15mx , ee6120b-8m sewage treatment plant model 8m , ee6120b-22233 ball bearing , ee6120b-22239 flexible coupling sleeve , ee6120b-20000 float switch n c , ee6120b-22250-2 rebuild kit mechanical seal, bearing, bushing and soft parts , ee6120b-62310 pushbutton perator only , ee6120b-22200-2 seal mechanical set , ee6120b-62312 switch 2 position operator only , ee6120b-62311 switch 3 position operator only , ee6120b-satempsw15mx temperature switch cell standard 100 degrees f , es7518d-022600-ip56 overboard pump and motor assy comp tefc-baldor ip-56 , ee6120b-19105 flowmeter 4 scale 1 by 8 npt 12m-12mx briners , ee6120b-19138 valve solenoid 1 by 4 120v-seal flush , ee6120b-19140 valve solenoid 3 by 4 120vac-briner , ee6120b-11198 3 by 4 y-strainer pvc sched 80 , ee6120b-58180 replay thermal overload 380-415-480 vac , ee6120b-62300 pilot light without lens, 120v , ee6120b-62306 lens, white pilot light , ee6120b-62305 lens, green pilot light , ee6120b-62119 bulb, replacement pilot light , ee6120b-62309 nc contacts , ee6120b-22219 radial cutter , ee6120b-22217 axial cutter , ee6120b-22220 impeller washer , ee6120b- 22253 impeller , ee6120b-22202 5 by 8 coupling flanges pump side , ee6120b-22238 7 by 8 coupling flange motor side , eh3370v-214611 1 hp motor , eh3370v-214601 2 hp motor , ee6120b-22607 bolt, impeller retaining , ee6120b-22608 collar, impeller drive , ee6120b-19800dp dosing pump 120v , ee6120b- sahingebc hinge, book cell, mechined , ee6120b- 22601 housing o ring , ee6120b-022201-4 macerator pump only , ee6120b-19800mm mixer motor-115 v single phase 1 by4hp , ee6120b-62430 replay control 4pole 14pin 120vac col lighted , ee6120b-22603 seal head , ee6120b-22602 shaft , ee6120b-22201 key , ee6120b-22619 shaft flange , ee6120b-72628 orific plate titanium for 1 1 by 2 t by u ball valve , ee6120b-99627 o ring valve end 1 1 by 2 tu ball valve , ee6120b-14011 flow control valve 1 0gpm , ee6120b-saejector ejector assembly vent line , ee6120b-66006 transformer gate board , ee6120b- 22612 slinger , ee6120b-22613 spacer, slinger , ee6120b-22617 pin, dowell , ee6120b-77032rt plate electrode 4 by 6 by 8 bipolar , ee6120b-77042rt plate electrode 4 by 6 by 8 primary anode , ee6120b- 77052rm plate electrode 4 by 6 by 8 primary cathode , es7518d-8mbct-03-na-ts book cell assembly 4 by 6 by 8 complete cell unit , ee6120b-62304 lens red pilot light , ee6120b-69000 printed circuit board , ee6120b-22223 cutter ring

corporations/Associations/Others

CTN :45387929

16 Jun, 2026 13.77 Lacs

Sonbhadra - Uttar Pradesh

Tender For supply of complete lube oil pump for aph sbandgb, pump s. no. 86882,3230, pump , steel ball, code no.183112700000, part no. 33, moc- en-8 , pump key, code no.170004010000, part no. 17, moc-en-8 , pressure plate, code no-204102101111, part no.14, moc-ms , hex bolt, code no-140005120000,part no.12, moc-steel , spring, code no. 203102010000, part no.13, moc-spring steel , front cover, code no.001002020000, part no. 10, moc-ci , fc bush, code no. 178021080000, part no. 9, moc-sintered bronze , rotor set, code no. 254021000000, part no. 6,7, moc-sintered iron , main bush, code no.178021080000, part no. 5, moc-sintered bronze , oil seal, code no. 172126120000, part no. 3, moc- nitrile , shaft, code no.249020010000,part no. 1, moc-en-8 , allen plug, code no.154506000000, part no. 15, moc-steel , aph sb and gb lop motor coupling with spider

CTN :45243141

09 Jun, 2026 12.78 Lacs

Murshidabad - West Bengal

Tender For procurement of different spares related to bottom ash clinker crusher and bottom ash system for overhauling of unit 2 scheduled in july august 2026.sgtpp - procurement of different spares related to bottom ash clinker crusher and bottom ash system for overhauling of unit 2 scheduled in july august 2026.sgtpp, cam segment for clinker crusher for bottom ash crusher dcips drawing no-25p06-t-1b-582,material-durite,bhn:500, shaft with shaft struct & shaft sleeve for bottom ash crusher dcips moc-en24 & ss 410,drawing no 25p06-t-1b-582, wear plate front for clinker crusher for bottom ash crusher dcips drawing no-25p06-t-1b-582,material-durite,bhn:500, wear plate back for clinker crusher for bottom ash crusher dcips drawing no-25p06-t-1b-582,material-durite,bhn:500, wear plate side for clinker crusher for bottom ash crusher dcips drawing no-25p06-t-1b-582,material-durite,bhn:500, gland for packing for bottom ash crusher dcips moc-ci fg-260 is:210,drawing no 25p06-t-1b-582, packing gland follower for bottom ash crusher dcips moc-bronze ltb 2,is:318,drawing no 25p06-t-1b-582, packing gland flange for bottom ash crusher dcips moc-ms,is:2062 gr-a,drawing no 25p06-t-1b-582, lantern ring for bottom ash crusher dcips moc:brass ltb-2,is318,as per dcips drawing no 25p06-1b-t-722, labyrinth ring of bearing housing moc-ms is 2062,for ahp-ifor clinker grinder,make-dcips, cam bolt for exen crusher for bottom ash crusher size: m20 x 65 long,sq.head,thread length 34 mm with nut,lock nut & spring washer.m.o.c: en8, chain simplex for bottom ash crusher dcips drawing no 25p06-t-1b-582, sprocket drive and driven for bottom ash crusher dcips drg.no.28p03-1b-t-582(rev-2), feed sump for bottom ash clinker crusher for bottom ash crusher dcips as per dcips drawing no 25p06-1b-t-722, nozzle tip with ceramic insert # 2,13 dcips for jet propulsion pump,part no-2&13,as per dcips drawing n0.-25p06-1b-t-591# for jet propulsion pump,as per dcips drawing n0.-2 5p06-1b-t-591 sgtpp1, nozzle inlet for jet pump for jet pump sgtpp dcips moc: fg,is 210,as per dcips dwg no 25p06-t-1b-591, throat cum disch pipe of jet pump for jet pump sgtpp dcips moc: durite(bhn 500-550),as per dcips dwg no 25p06-t-1b-591, punched washer type a for jet pump,moc:ss410/416,as per dcips punched washer (type dcips punched washer (type a) for m 20 bolts is 2016 of of jet pulsion pump,as per drawing,part no-05,material: steel, guide angle lh for ba feed gate for ba feed gate dcips moc-ms is:2062 gr a,drawing no 25p06-1b-t-572, guide angle rh for ba feed gate for ba feed gate dcips moc-ms is:2062 gr a,drawing no 25p06-1b-t-572, gate roler fitted with bush for ba feed gate dcips drawing no-25p06-t-1b-572,material-steel-is:1030, renewable seat lip for ba feed gate for ba feed gate dcips moc-ms is:2062 with ss316 lip,drawing no 25p06-1b-t-572, adjustable seating wedge # for bottom ash feed gate assembly as per drawing no.28p03-1b-t-576(rev-2), enclosure cover plate # dcips for bottom ash hopper feed gate enclosure, moc:ms,is:2062,10mm thk,as per dcips drawing no 25p06-t-1b-572, gasket,for ba feed gate access door for bottom ash moc: neoprene rubber , dcips drg no: 25p06-1b-t-572, gasket for feed gate enclosure for ba feed ga moc: neoprene rubber, elbow,200nb x45 for wet ash system sgtpp dcips moc: durite (alloy c.i),bhn:450-500,as per dcips dwg no 25p06-1b-t-831, elbow,200nb x90 for wet ash system sgtpp moc: durite (alloy c.i) bhn:450-500.as per dcips dwg no 25p06-1b-t-835, lateral,200nbx45 p/p/p for wet ash system sgtpp ba slurry line.moc: durite(alloy c.i) bhn: 450-500, guide angle bracket for ba feed gate for ba feed gate dcips moc-ci fg-220 is:210,drawing no 25p06-1b-t-572

Central Government / Public Sector

CTN :45265657

10 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For supply of set of gate drive unit cards for traction converter, each set consisting of (1) gate drive unit card dytp 155a (line side), bti part no. tc3est000229-9009 - 1 no/qty. (2) gate drive unit card dytp 155a (motor side), bti part no. tc3est000229-9009 -02 nos/qty. [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government/Public Sector

CTN :45203133

21 May, 2026 13.22 Lacs

Visakhapatnam - Andhra Pradesh

Tender For repair of bag house equipment in crmp- 1) cage repair( bending minor welding & painting), 2) cleaning and fixing of bags( opening the chamber, removing the venturies, taking out bags cleaning with and refixing) once in year, 3) cleaning of dust collecting hopper of bag house, 4) repair of dust hopper and its doors, 5) bag house screw conveyor body repair, 6) bag house screw conveyor hanger bearing with shaft changing, 7) bag house screw conveyor end bearing changing, 8) bag house screw conveyor coupling repairs, 9) bag house screw conveyor changing, 10) en masse conveyor drive sprocket changing, 11) en masse conveyor tail sprocket changing., 12) en masse conveyor drive chain fixing, 13) en masse conveyor links changing, 14) en masse conveyor drive unit coupling repair, 15) en masse conveyor drive chain rejointing in snap, 16) maintenance of rotary air locks (twice in a year), 17) bucket elevator belt rejointing in case of snap, 18) bucket elevator drive pulley changing, 19) bucket elevator boot pulley changing, 20) bucket elevator fallen buckets fixin, 21) pulse jet solenoid valves repair and maintenance, 22) drier maintenance in compressor house (4 driers), 23) maintenance of compressed air pipe line, 24) id fan casing removal and fixing back to faciltate for fan changing, 25) id fan casing cutting and fixing back during bearing changing, 26) id fan casing changing, 27) id fan casing repair work, 28) id fan suction duct patch work, 29) id fan delivery duct patch work, 30) to make arrangement for chimney cleaning on id fan delivery duct near chimney and duct opening and closing there.., 31) dust hopper gate replacement, 32) dust hopper vibrofeeder replacement, 33) dust hopper body repair patch work, 34) flexible hose to pulse jet replacement, 35) pulsing pipe changing, 36) pulsing pipe repair, 37) cyclone patch work, 38) flue gas duct leaks arresting patch works.

Central Government/Public Sector

CTN :45012954

12 May, 2026 NA

Bhusawal - Maharashtra

Tender For supply of gate unit line converter,drive converter and over voltage protectio (pos no.227,228,229)type gv a 587-a01,56 a-48 vac-hucd685038 abb document no-hucd 320054r1001 . [warranty period: 30 months after the date of delivery ]

Rotor Set Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government And Public Sector

Central Government / Public Sector

corporations/Associations/Others

Central Government / Public Sector

Central Government/Public Sector

Central Government/Public Sector