Tender For purchase of renewable energy practical equipments - equipments for renewable energy practices:, rc phase shift oscillator oscillator type: rc phase shift oscillator using transistor / op-amp configuration. input supply: 230 v / 50 hz ac with regulated internal dc supply. output frequency range: 100 hz 10 khz adjustable. output: sinusoidal waveform with adjustable amplitude up to 10 vpp. rc network: three-stage rc phase shift network with frequency control arrangement. cro test points: dedicated cro terminals at amplifier output, each rc stage, and final output for waveform and phase-shift observation. protection: over-voltage and short-circuit protection provided. indicators and controls: power on led indication with frequency and gain adjustment controls. accessories: patch cords, circuit diagram, strain guage characteristics kitac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords, load cell characteristics kit input supply: 230 v / 50 hz ac with regulated internal dc supply. sensor: strain gauge load cell with suitable mounting arrangement. load range: 0 10 kg. display: digital display for load/output indication. cro / test points: test points provided for observing bridge output, amplifier output, and signal conditioning stages. controls: zero adjustment and calibration controls provided. protection: overload and short-circuit protection provided. accessories: loading arrangement, connecting leads., measurement of tank level using rotometer input supply: 230 v / 50 hz ac with regulated internal dc supply. tank arrangement: transparent tank with 30 liters capacity with suitable supporting stand. rotameter range: 0 4000 l/hr calibrated rotameter. flow system: pump, control valves, and piping arrangement provided for continuous flow operation. measurement facility: provision for flow-based tank level measurement and observation. display / observation: calibrated level indication with flow monitoring arrangement. test points: output terminals provided for monitoring sensor/output signals. accessories: connecting tubes., measurement of tank level using displacer type level transmitter input supply: 230 v / 50 hz ac with regulated internal dc supply unit. measurement principle: buoyancy (archimedes principle) using displacer element. tank arrangement: transparent experimental tank with 30 liters capacity and suitable mounting stand. level range: suitable laboratory-scale level measurement (0 100% tank height). sensor system: displacer type level transmitter with continuous level output signal. display unit: digital indicator for level display in percentage / engineering units. output signals: standard analog output (4 20) ma / (0 10) v provided for monitoring. test points: provided for transmitter output, signal conditioning, and display unit verification. controls: zero and span calibration adjustment provided for setting level reference. protection: over-voltage and short-circuit protection for electronic modules. accessories: connecting cables, piping arrangement, loading medium (water), measurement of temperature using pt100 input supply: 230 v / 50 hz ac with regulated internal dc power supply unit. sensor: pt100 resistance temperature detector (rtd) probe with stainless steel sheath. measurement principle: resistance variation of platinum element with temperature. temperature range: 0 c to 150 c (or suitable laboratory range). display unit: digital temperature indicator with direct c display. accuracy: high accuracy with linearized rtd signal conditioning circuit. sign
Tender For purchase of lab equipments for res dept - purchase of lab equipments for res dept, rc phase shift oscillator (iemcode:o001)specifications: oscillator type: rc phase shift oscillator using transistor / op-amp configuration. input supply: 230 v / 50 hz ac with regulated internal dc supply. output frequency range: 100 hz 10 khz adjustable. output: sinusoidal waveform with adjustable amplitude up to 10 vpp. rc network: three-stage rc phase shift network with frequency control arrangement. cro test points: dedicated cro terminals at amplifier output, each rc stage, and final output for waveform and phase-shift observation. protection: over-voltage and short-circuit protection provided. indicators and controls: power on led indication with frequency and gain adjustment controls. accessories: patch cords, circuit diagram., strain guage characteristi cs kit(iemcode:o002)specifications: ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. no rs.10,000 2 table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords, load cell characteristi cs kit(item code: o003)specifications:input supply: 230 v / 50 hz ac with regulated internal dc supply. sensor: strain gauge load cell with suitable mounting arrangement. load range: 0 10 kg. display: digital display for load/output indication. cro / test points: test points provided for observing bridge output, amplifier output, and signal conditioning stages. controls: zero adjustment and calibration controls provided. protection: overload and short-circuit protection provided. accessories: loading arrangement, connecting leads., measurement of tank level using rotometer(item code: o004)specifications: input supply: 230 v / 50 hz ac withregulated internal dc supply. tank arrangement: transparent tank with 30 liters capacity with suitable supporting stand. rotameter range: 0 4000 l/hr calibrated rotameter. flow system: pump, control valves, and piping arrangement provided for continuous flow operation measurement facility: provision for flow-based tank level measurement and observation. display / observation: calibrated level indication with flow monitoring arrangement. test points: output terminals provided for monitoring sensor/output signals. accessories: connecting tubes., measurement of tank level using displacer type level transmitter(item code: o005)specifications: input supply: 230 v / 50 hz acwith regulated internal dcsupply unit. measurement principle:buoyancy(archimedesprinciple) using displacerelement tank arrangement: transparent experimental tank with 30 liters capacity and suitable mounting stand. level range: suitable laboratory-scale level measurement (0 100% tank height). sensor system: displacer type level transmitter with continuous level output signal. display unit: digital indicator for level display in percentage / engineering units. output signals: standard analog output (4 20) ma / (0 10) v provided for monitoring. test points: provided for transmitter output, signal conditioning, and display unit verification. controls: zero and span calibration adjustment provided for setting level reference. protection: over-voltage and short-circuit protection for electronic modules. accessories: connecting cables, piping arrangement, loading medium (water), measurement oftemperature using pt100(item code: o006a)specifications: input supply: 230 v / 50 hz ac with regulated internal dc power supply unit. sensor: pt100 resistance temperature detector (rtd) probe with stainless steel sheath measurement principle: resistance variation of platinum element with temperature. temperature range: 0 c to
Tender For supply of lab equipments - purchase of lab equipments, four stroke petrol engine test rig specifications: single cylinder, 4-stroke spark ignition, petrol engine. air cooled rope brake arrangement with spring balance for loading . speed :1500 3500rpm power 3 hp. panel board for measuring speed with power supply and tacho generator setup, burette with tank assembly. load test test rig kit . heavy-duty fabricated ms base frame anti-vibration mounting arrangement powder-coated / painted finish , saybolt viscometer apparatus specifications: glass type: high-quality borosilicate glass tube. control type: manual energy regulator control. shape: rectangular bath with cylindrical test chamber. temperature range: ambient to 240 c oil bath temperature. humidity: up to 80% rh (non-condensing). power supply: 230 v ac, 50 hz. measuring range: 32 to 1000 sus(saybolt universal seconds). accuracy: as per astm d-88( 0.2 seconds). mounting type:benchtop. capacity:one cup(approximately 60 ml). control mode:manual operation. port size:standard orifice sizeas per astmd-88. features:oil bath with heater, thermoregulator, insulated outer body, orifice, receiver flask., cleveland open cup (coc) apparatus specifications: standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 c per minute (as per standard) temperature range: (-6 to 400) c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valve body: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation, pensky-martens closed cup apparatus specifications: standard compliance: astm d93 / is 1448 (part 21) type: pensky-martens closed cup (motorized, digital type preferred) test cup: brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system: heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) digital temperature display power supply: 230v ac, 50 hz safety: over-temperature cut-off flame safety control
Tender For purchase of non consumable item in hydraulic lab for civil department - bernoullis theorem apparatus(closed circuit)(code e001)bernoulli apparatus flow rate range up to ~20 l/min or more (depending on pump) pump power ~0.5 kw / -1 hp pressure measurement ~0 290 mm to 370 mm wc measuring tank 25 50 l utility 230 v ac, single phase, venturimeter and orifice meter apparatus (closed circuit)(code e002)orifice & mouthpiece apparatus set of orifices: usually 2 sizes (e.g., 8 mm, 10 mm) or more. set of mouthpieces: several l/d ratios (e.g., 10 mm dia with l/d 1, 2.5, 4). sump tank capacity: ~70 100 l. constant head tank: ~20 35 l. measuring tank: ~25 40 l with scale. pump: 0.5 hp monoblock / centrifugal pump (single phase). instrumentation: hook gauge / pointer gauge for head/jet measurement; stopwatch. power supply: 220 230 v ac, single phase., pipe friction apparatus (closed circuit) with all acceeories(code e003)pipe friction apparatus test pipe length ~1 m per pipepipe diameters 12 mm 25 mm (varies)sump tank capacity ~40 l 100 lvolumetric tank ~40 lpressure range (manometer) ~300 500 mm water / mercuryflow rate range 0 60 l/minpump 0.5 hp centrifugal, centrifugal pump testing rig with all accessories(code e004)single speed centrifugal pump testrig (closed circuit) (heavy duty)a. single speed stainless steel centrifugal (mono block) pump set of size 25mm a 1hp, 2880rpm, single phase 50 cycles, 200/220 volts ac electric motor. to discharge about 100lpm at 10 meters head at a single speed of 2880 rpmb. switch and dol starter for the above pump set and an energy meterc. piping system consisting of pipes, valves, and fittings with pressure and vacuum gauges (gi/pvc).fibreglass lined s.s. measuring tank of size 500x500x600mm height provided with a gauge glass, scale and adrainvalve. fibreglasslined s.s. sump of size 1500x500x300 mm height capacity rigid stainless steel frame work compactly fitted with all the above items as a self sufficient package, reciprocating pump testing rig(code e030)reciprocating pump apparatus type of pump single acting reciprocating pumpcylinder bore 50 80 mmstroke length 100 150 mmspeed 30 60 rpmdischarge 5 20 lpmsuction head up to 5 mdelivery head up to 20 mmotor power 0.5 1 hpmotor speed 1440 rpmpower supply 230 v ac, single phasepressure gauge range 0 5 kg/cm vacuum gauge range 0 760 mm hgmeasuring tank capacity 30 50 litersmaterial cast iron pump, ms framedrive belt drive / direct coupling, mouthpiece & orifice setup(code e002 )experiments : to determination of cd, cv, and cc of venturi meter.specificationsventuritype : acrylicsize/dimension : 350mm 350mm 600mmnominal size : 25 mmend connection : gi pipeusage/application : laboratorybody material :stainless steelorifice meterapparatusexperiments : to determination of cd, cv, and cc of orifices meter.specificationspump : hp centrifugal pump.ac motor : hp 230v ac.supply tank : 120 ltrs. made of ms with frp lining.measuring tank : 40 ltrs. made of ms with frp lining and fitted with piezo meter tube & scale.piping &fittings : gi/pvc with necessary valves.fitted with u-manometer with mercury.control panel : 1hp dol starter.digital timer : mcb load and line indicator.
Tender For supply, erection, testing & commissioning of lt panel consisting of 400a 50ka 4 pole microprocessor based mccb - 02 nos as incoming , 200a/250a 36ka 4 pole microprocessor based mccb-03 nos, 63a 36ka 4 pole microprocessor based mccb-02 nos and 63a 10ka dp 2pp mcb - 02nos as outgoing, all mccbs shall be with rotary switch, with voltmeter,ammeter, led indicator lamp,cu. bus bar , neutral link, earth bar, spreader link, lock and key feature arrangement cable gland etc. with suitable sheet steel enclosure conforming to cege/grc's specification no. ser/elec/gs/description/ltpanel/1/rev-0/mar2024 or latest.minimum size of panel 1800 mm (h)x 2400mm (l) x 600 mm(d). [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of interactive panels with cpu (q2) , professional large format display (v2) (q2) , weighing machine , mill house , fully automatic jaggery production unit , solar panel foundation and all related items , structure of complete plant , bought out for complete plan , erection of mill house and boiling house , hdg set , submersible , fire fighting equipment , hcl kit single , oilfree 15 com , air filter , cylinder c2h2 , regulator c2h2 , hood aas , vacuum hot air oven , digital hot air oven , air circulation fan , microprocessor digital temperature indicator , digital timer , heating mantle , digital muffle furnace , single beam uv , double beam uv , digital photo colorimeter , weighing balance , analytical balance cy , water bath , pid temperature controller , atomic absorption spectrophotometer , gas chromatography , fused silica capillary column , gas purification panel , electromechanical voltage stabilizer , carbon steel cylinder , pressure regulator , glassware , servo candy pillopack wrapping machine , horizontal flow wrapepillopack high speed packaging machine , automatic packing machine , vertical single face paper corrugating machine , corrugated sheet pasting machine , eccentric slotter machine , bar rotary cutting creasing machine , stitching machine , paper reel to sheet cutting machine , flexo graphic printing machine , printing machine , manual jar filling machine , manual pouch sealing machine , manual sticker labelling machine , bag sewing machine , bar coding equipment , bar reader machine , projector , laptop , public address audio system , pantry , desktop with accessorie , tv 45 inch screen , solar panel , bio fertilizer plant , cctv unit for control ) /bid number : gem/2026/b/7564787 * /dated: 26-05-2026 & & / bid document 1 / 42
Tender For corrigendum : tender for supply of rod gear fittings for frigate gsl yard nos 1258 and 59 - steel bulkhead and deck gland with conical gearing with brass bushing type 1 do 14 kb12 , steel bulkhead and deck gland with conical gearing with brass bushing type 2 do 21 , steel deck plate with stroke indicator with bevel gearing type 2 do 14 kb12 with brass bushing , steel deck plate with stroke indicator with bevel gearing type 2 do 27 kb 22 with brass bushing , tip for drive connection with steel fittings kb 9 dh14 , steel hinged coupling for roller do 14 , steel hinged coupling for roller do 21 , steel hinged coupling for roller do 27 , steel normal traveling coupling do 14 kb 11 , steel normal traveling coupling do 21 kb 11 , steel traveling coupling h 3 , steel normal traveling coupling do 40 kb 32 , steel extended traveling coupling do 14 kb 11 , steel extended traveling coupling do 21 kb 17 , steel quick release roller drive pipe connection dh32 , steel bulkhead and deck bearing with brass bushing type 1 do 21 kb 17 , steel bulkhead and deck bearing with brass bushing type 2 do 21 , steel bulkhead and deck straight gland type 2 do 21 with brass bushing , steel extended traveling coupling do 27 kb 22 , steel bevel gearing with brass bushing for roller do 14 , steel quick release roller drive pipe connection dh25