Latest screw pitch gauge Tenders | Government screw pitch gauge Tenders

corporations/Associations/Others

CTN :45723624

02 Jul, 2026 6.00 Lacs

Salem - Tamil Nadu

Tender For supply delivery and fixing of motor and accessories at ward-1 selliyampalayam oht in narasingapuram municipality - supply and delivery of kirloskar make 15hp/11kw/2900rpm three phase/415v/50hz/ac/tefc horizontal centrifugal monoblock pump impeller-mechanical seal (head-20mtr,flow rate-2154lpm) size:100x100mm (local quotation) 15hp horizontal centrifugal monoblock pump, labour charges for erection of horizontal shaft, centrifugal pumpset (coupled/monoblock) in bore well/open well including fixing of suction pipe and foot valve upto a maximum depth of 7 metres and delivery pipes to the required length with valves,pressure gauges upto the exterior wall of pump room and erection of panel board consisting of tpic switches starter, voltmeter, ammeter, capacitor single phasing preventor and laying and jointing the cables and twinearthing as per ie rules including providing bed blocks etc., complete and operating the pumps and trial run for 10 days including signing of completion of reports as required by eb authorities., three phase panel board star- delta with two level guard and auto start supply and delivery of star-delta starter confirming to is 13947, iec60947-1 and as amended thereafter with suitable kw rating for operation in ac/ three phase/50hz (+/- 5%) and 415v (+/- 10%) including 3 pole magnetic contactor with under voltage release - 3 nos., ct operated ammeter (65 mm dia) with suppressed scale,voltmeter (65mm dia),voltmeter selector switch,miniature circuit breaker, thermal overload relay, air break contactors suitable for next standard higher kw rating, single phasing preventor, dry running preventor and on/off push button switches, wiring with 1 sq.mm/4 sq. mm copper pvc insulated cable, powder coated vermin proof box, including the capacitor (the cost of capa citor is to be taken separately). three phase panel board for 15hp, supply,delivery and fixing of the following materials are listed below etc..,as directed by the departmental ofiicers.for service4 core 16sq.mm pvc copper ug cable, for motor3 core 6sq.mm pvc insulated and sheathed flat type copper cable, 150mm di pipe, 100mm gi pipe , 100mm gi flange set, rubber sheet for flange set, ms bolt and nut20mm dia and above x 90mm to120mm length fully threaded bolts andwith nuts 2 nos. , manhole cover 60 x 60cm (heavy duty) with frame, supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary ms flange of table e , gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the departmental officers. 150mm sluice valve, 100amps 4pole mcb, 100amps porcelain fuse unit (500v), 32mm pipe

CTN :45689893

25 Jul, 2026 NA

Parganas - West Bengal

Tender For supply of 45 types of gauges for extractor - chamfer gauge for extractor , chamfer gauge for extractor , chamfer gauge for extractor , chamfer gauge for extractor , chamfer gauge for extractor , gap limit gauge , gap limit gauge , gap limit gauge for extractor , gap limit gauge for extractor , gap limit gauge for extractor , gap limit gauge for extractor , gap limit gauge for extractor , gap limit gauge for extractor , gap limit gauge , hole depth gauge for extractor , plug gauge for extractor , plug gauge for extractor , plug gauge , plug gauge for extractor , plug gauge , plug gauge for extractor , plug gauge for extractor , position gauge , position gauge for extractor , position gauge for extractor , position gauge for extractor , profile gauge for extractor , radius gauge for extractor , receiver gauge for extractor , receiver gauge for extractor , receiver gauge for extractor , receiver gauge for extractor , receiver gauge for extractor , receiver gauge for extractor , slip gauge for extractor , slot depth gauge for extractor , slot depth gauge for extractor , support for extractor , chamfer gauge for extractor , position gauge for extractor , position gauge for extractor , receiver gauge for extractor , receiver gauge for extractor , receiver gauge for extractor , receiver gauge for extractor

Central Government And Public Sector

CTN :45653040

30 Jun, 2026 NA

Bangalore - Karnataka

Tender For unified screw pitch gauge to make mitutoyo model no 188-111 or exactly similar in baker/starrett/accu. note: calibration/ test certificate from nabl shall be submitted along with the supply [ warranty period: 30 months after the date of delivery ] ]

CTN :45506359

01 Jul, 2026 NA

Mumbai - Maharashtra

Tender For tender for supply of spares for tank content gauges - hydrobar fr inside with 4m sensor cable , hydrobar fr outside with 6m sensor cable , san8000 high temp pressure transmiter with 4m sensor cable , terminal box with bracket , pcb set for rda860 , pressure transmitter model hydrobar inside mounted , sensor pressure transmitter for feed water outside mounted , 3x1 0 sq mm atc std cond frls sheated cable as per ied 92 3 , ss316 ball valves 65nb , tank display unit model rda 860 , central display unit model cdu , junction box 2x2 way , rda 860 structure including pcb set and keyboard , hydrobar for tank depth above 4m inside , tank content indicator panel rda528 8channels , presure transmitter model hydrobar outside mounted , termination box

CTN :45484021

09 Jul, 2026 NA

Raipur - Chhattisgarh

Tender For supply of driver of 5 pieces 100 mm to 300 mm , soldering iron 125watt 230volt , temperature controlled soldering 50 watt 230 volt iron , i motor pump set 1 hp 1 phase 240 v , cabinet dryer electrical , pipe bending machine hydraulic type 12mm to 30mm , industrial sewing machine , fuel injection pump ve pump distributor fuel rotary pump dpc , phase sequence indicator 3 phase 415 v , pipe threading die with handle ratchet type die head of 12 34 and 1 , tachometer digital photo sensor type 10000 rpm , screw driver insulated 6mm 150 mm diamond head , punch centre 10 mm 150 mm , micrometer inside with extension rods accuracy 001 mm with extension rods up to 150 mm , steel measuring tape 20 mts , hacksaw frame fixed type 300 mm , dial gauge type 1 gr a complete with clamping devices and with , h washing machine semi automatic 5 kg , safety harness , auto darkening welding helmet , inverter with battery 1kva , depth micrometer 025mm accuracy 001mm , motorised bench grinder 1 hp 3 phase 440vdia150 mm , battery charger 0 6 9 12 24 48v 30amp , air ratchet with standard accessories , safety belt standard quality , drilling machinebenchtodrill up to 12mm dia along with accessories , electrical test bench , cutting knives , pocket steel tape 6 long , measuring tape 30m , measuring steel tape 15m , pliers round nose 15 cm , spoons wooden ladle , face shield , moisture box aluminium 100gm capacity , cleaning tray 45 30 cm , spanner t flocks for screwing up and upscrewing inaccessible , wheel barrow , spade , pocker , hacksaw frame fixed 150 mm , piston ring compressor , electric testing screw driver , connecting screw driver 100 mm , rotary switch 16 a440v , ph meter rod , lead light , chisels cross cut 200 mm 6mm , tweezers 100 mm , induction cooktop with following feature , glass rod , bradawl , circlip pliers expanding 15cm and 20cm , number punch 6 mm , desiccator , pipe cutting tool up to 5cm dia , chamois , electric iron automatic 750 w 240 v , belt sander narrow surface , trowelbrick 10 25cm long , pipe cutter wheel type 6 mm to 25 mm , digital vernier caliper universal type 0 150 mm lc 005 mm , heat sealing machine handpedal operated , feeler gauge 20 blades metric , screw pitch gauge metric 025 to 6 mm , beaker 50 100 250 ml 500 ml , pliers side cutting 15 cm , sleeve drill morse 0 1 1 2 2 3 3 4 4 5 , hydrometers of different ranges 030 3060 6090 brix , grease gun 05 ltr capacity , portable sanding machine 600w , water purifier ro and uv technologies , ph meter digital , hand rubber gloves tested for 5000 v , earth clamp , portable electric drill machine 15 mm drill bit capacity , measuring cylinder 100mi250ml 200 ml 500ml , pliers round nose insulated 100 mm , hammer extractor type250 grams , pipe flaring tool , thermostat , particle masks , soldering iron changeable bits 15w , spanner adjustable drop forged ss 150 mm , professional air blower power consumption 820 w , plier side cutting 200mm , washing machine automatic , microwave oven , pliers flat nose insulated 200 mm , utility knife , e ac ceiling fan and ac table fan 68 watt 230 v each , electric mixer , lugs for cable , pully puller with 3 legs 300mm , rheostat sliding type 0 25 ohm 2 amp , temperature gauge range 0 to 150 c , rheostat sliding type 0 1 ohm 10amp , conical flask 50 100 250ml 500ml , shredder for slicing of fruit and vegetable capacity 5kghrs , torque wrenches 535 nm , chisel cold round nose 9 mm 100 mm , weighing balance digital , electric soldering iron 35 w , rheostat sliding type 0 10 ohm 5 amp , impact wrench 1 to 2 inch drive , plier flat nose 150 mm , digital vernier caliper 0 150mm least count 002 , measuring tape (v3) (q3) //bid details 2 / 81

Central Government And Public Sector

CTN :45252556

19 Jun, 2026 NA

Kudankulam - Tamil Nadu

Tender For corrigendum : supply of interchangeable anvil - lc 0.01 mm - as per annexure c - range 700-800 mm , supply and delivery of analog outside micrometer with interchangeable anvil - lc 0.01 mm - as per annexure c - range 800-900 mm , supply and delivery of analog outside micrometer with interchangeable anvil - lc 0.01 mm - as per annexure c - range 900-1000 mm , supply and delivery of analog groove micrometer - with inside and outside measurement - as per annexure d - range 0-25 mm , supply and delivery of analog groove micrometer - with inside and outside measurement - as per annexure d - range 25-50 mm , supply and delivery of telescopic gauge set with 6 number of gauges - as per annexure e - range 8-150 mm , supply and delivery of micrometer stand - as per annexure f - adjustable - range upto 100 mm , supply and delivery of micrometer stand - as per annexure f - fixed - range upto 50 mm , supply and delivery of - analog long jaw caliper with fine adjustment as per annexure g - range 0-300 mm , supply and delivery of - analog long jaw caliper with fine adjustment as per annexure g - range 0-500 mm , supply and delivery of - analog long jaw caliper with fine adjustment as per annexure g - range 0-750 mm , supply and delivery of - analog long jaw caliper with fine adjustment as per annexure g - range 0-1000 mm , supply and delivery of - analog offset type caliper as per annexure h - range 0-200 mm , supply and delivery of - digital back jaw edge to centre type caliper as per annexure i - range 10.1 to 200 mm , supply and delivery of - digital back jaw edge to centre type caliper as per annexure i - range 10.1 to 300 mm , supply and delivery of - digital back jaw centre to centre type caliper as per annexure j - range 10.1 to 200 mm , supply and delivery of - digital back jaw centre to centre type caliper as per annexure j - range 10.1 to 300 mm , supply and delivery of analog pointed type caliper as per annexure k - range 0-150 mm , supply and delivery of analog knife type caliper as per annexure k - range 0-300 mm , supply and delivery of analog knide edge type caliper as per annexure k - range 10-200 mm , supply and delivery of analog swivel type caliper as per annexure k - range 0-200 mm , supply and delivery of magnetic dial stand suitable for holding stem sizes 6 mm and 8 mm as per annexure l , supply and delivery of magnetic dial stand suitable for holding stem sizes 4 mm, 8 mm and 3 per 8 inch as per annexure l , supply and delivery of magnetic dial stand with fine adjustment suitable for holding stem sizes 6 mm and 8 mm as per annexure l , supply and delivery of magnetic dial stand with fine adjustment suitable for holding stem sizes 4 mm, 8 mm and 3 per 8 inch as per annexure l , supply and delivery of magnetic dial stand - mini - as per annexure l , supply and delivery of magnet dial stand - universal - as per annexure l , supply and delivery of precision level as per annexure m , supply and delivery of precision level- box type as per annexure m , supply and delivery of radius gauges - 26 leaves 90 degree arc - 0.5-13 mm - as per annexure n , supply and delivery of radius gauges - 34 leaves 180 degree arc - 1-7 mm - as per annexure n , supply and delivery of radius gauges - 32 leaves 180 degree arc- 7.5 -15 mm - as per annexure n , supply and delivery of radius gauges - 30 leaves 180 degree arc-15.5 - 25 mm - as per annexure n , supply and delivery of metric screw pitch gauges - 21 leaves - 0.4 -7 mm - as per annexure o , supply and delivery of unified screw pitch gages - 30 leaves - 4-42 tpi - as per annexure o , supply and delivery of whitworth screw pitch gages - 28 leaves - 4- 60 tpi - as per annexure o , supply and delivery of digital vernier depth gauge - hook end - 10.1-210 mm - as per annexure p , supply and delivery of digital vernier depth //bid details 2 / 83 annexure p , supply and delivery of digital vernier depth gauge - mini - 0- 25 mm - as per annexure p , supply and delivery of dial depth gauge - 0-200

CTN :45441089

18 Jun, 2026 NA

Bazpur - Uttarakhand

Tender For supply of tools and tackels in sugar mill - roller grooving tool size- x 6 x 40 isi/iso standard, size- x 6 x 45 isi/iso standard, size- x 6 x 50 isi/iso standard, size- 1 x 12 x 40 isi/iso standard, size- 1 x 12 x 45 isi/iso standard, size- 1 x 12 x 50 isi/iso standard, size- 1, x 12 x 40 isi/iso standard, size- 1, x 12 x 45 isi/iso standard, size- 1, x 12 x 50 isi/iso standard, carbide cutting tools. size: x 4 right hand. isi/iso standard, size: x 4 left hand. isi/iso standard, size- 1 x 6 right hand. isi/iso standard, size- 1 x 6 left hand. isi/iso standard, size- x 6 right hand isi/iso standard, size- x 6 left hand isi/iso standard, carbide tips all size isi/iso standard, h.s.s. tool bit all size isi/iso standard, tapper shank dril all size . isi/iso standard, straight shank dril all size. isi/iso standard, files all size. isi/iso standard, tape set of (3 piece) bsw all size. isi/iso standard, tap set of (3 piece) mm. all size. isi/iso standard, die nut inch/mm all size. isi/iso standard, d. spanner set all size. isi/iso standard, ring spanner set all size. isi/iso standard, box spanner set all size. isi/iso standard, pipe rinch all size. isi/iso standard, measuring tape 3 meter long . isi/iso standard, do - 5 meter long. isi/iso standard, do - 15 meter long. isi/iso standard, tin cutter 10 . isi/iso standard, do - 16 isi/iso standard, revolving centre 3 m.t. isi/iso standard, revolving centre 4 m.t. isi/iso standard, revolving centre 5 m.t. isi/iso standard, oil can capacity 200 m.l. isi/iso standard, screw pitch gauge. isi/iso standard, wooden saw(circular saw)1/8 x 18 isi/iso standard, drill socket (i) size 0 1 isi/iso standard, (ii) size- 1 2 isi/iso standard, (iii) size- 2 3 isi/iso standard, (iv) size- 3 4 isi/iso standard, (v) size- 4 5 isi/iso standard, h.s.s. black tool bar square high grade all size, steel rule 12 . isi/iso standard, steel rule 24 . isi/iso standard, screw driver set all types and sizes. isi/iso standard, pliar all type and sizes. isi/iso standard, drill chuck straight size: 1/8 to isi/iso standard, carbide tips only (all size) isi/iso standard, high carbon steel tool 10% cobalt size: to 1 isi/iso standard, knurling tool multi purpose. isi/iso standard, carbide tip tool (with handle) k-20 for (roller grooving) (i) size- 1, x 12 x 40 isi/iso standard, (ii) size- 1, x 12 x 45 isi/iso standard, (iii) size- 1, x 12 x 50 isi/iso standard

CTN :45404385

17 Jun, 2026 NA

Howrah - West Bengal

Tender For supply of set of gauges for checking screw coupling of transition cbc. the above item consists of 06 various types of gauges as follows: 1) condemning gauge for short shackle screw coupling size: go-29.50 mm & no go-25.0 mm. asper rdso drg. no. 4685 & rdso-mp-mi-no-25. rev.0, jan 2006. material specification: tool steel to is no. 3748/90. hardness 50/55 hrc. qty = 1 no/set. 2) condemning gauge for long shackle screw coupling size: go-45.0 mm & no go-39.50 mm. as per rdso drg. no. 4685 & rdso-mp-mi-no-25. rev.0, jan 2006. material specification: tool steel to is no. 3748/90. hardness 50/55 hrc. qty = 1 no/set. 3) condemning gauge for checking the play between the hole short shackle & trunion screw pin condemning size: 187.0 mm. as per rdso drg. no. 4685 & rdso-mp-mi-no-25. rev.0, jan 2006. material specification: tool steel to is no. 3748/90. hardness 50/55 hrc. qty = 1 no/set. 4) condemning gauge for checking the play between the hole long shackle & trunion nut pin condemning size:278.0 mm. as per rdso drg. no. 4685 & rdso-mp-mi-no-25. rev.0, jan 2006. material specification: tool steel to is no. 3748/90. hardness 50/55 hrc. qty = 1 no/set. 5) screw pitch gauge (go & no go) (knuckle thread -lh) size: r- 1.404mm & r-1.625 mm. as per rdso-mp-mi-no25. rev.0, jan 2006. qty = 1 no/set. 6) screw pitch gauge (go & no go) (knuckle thread - rh) size: r1.515 mm & r- 1.625 mm. qty = 1 no as per rdso-mp-mi-no-25. rev.0, jan2006. qty = 1 no/set. [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45072404

04 Jun, 2026 NA

Bangalore - Karnataka

Tender For corrigendum : tender for supply of 32 types of tools - battery gun standard , feeler gauges 0.05mm to 1.0mm , torque wrench 5 to 25 nm , torque wrench 1 to 200 nm , allen key set 1.5 to 32 mm , magnetic lifter for fod & removal , vacuum cleaner portable , inspection mirror flexible , stop watch digital , knock out punch de rivetting , tap wrench , strap wrench capacity 125 mm , electronic soldering iron 230v 68w , hand tap m5x0.8 to 6h for tapping , hand tap m6x1 to 6h for tapping , helicoil hand tap set m 4 x 0.7 set of 3 , helicoil hand tap set m 5 x 0.8 set of 3 , helicoil hand tap set m 6 x 1.0 set of 3 , helicoil hand tap set m 8 x 1.0 set of 3 , helicoil hand tap set m 8 x 1.25 set of 3 , helicoil hand tap set m 10 x 1.25 set of 3 , helicoil hand tap set m 12 x 1.25 set of 3 , helicoil hand tap set m 24 x 2.0 set of 3 , helicoil hand tap set m 30 x 2.0 set of 3 , helicoil thread plug gauge m2 x 0.4 , engraving gun 230v ac , centre punch 4 , oil can capacity 500 cm3 , measuring jar 5 litres , spirit level for levelling purpose , rivet removal tool , depth gauge

CTN :45105964

21 May, 2026 NA

Bazpur - Uttarakhand

Tender For supply of tools and tackles materials in sugar mill - roller grooving tool size- x 6 x 40 isi/iso standard, size- x 6 x 45 isi/iso standard, size- x 6 x 50 isi/iso standard, size- 1 x 12 x 40 isi/iso standard, size- 1 x 12 x 45 isi/iso standard, size- 1 x 12 x 50 isi/iso standard, size- 1, x 12 x 40 isi/iso standard, size- 1, x 12 x 45 isi/iso standard, size- 1, x 12 x 50 isi/iso standard, carbide cutting tools. size: x 4 right hand. isi/iso standard, size: x 4 left hand. isi/iso standard, size- 1 x 6 right hand. isi/iso standard, size- 1 x 6 left hand. isi/iso standard, size- x 6 right hand isi/iso standard, size- x 6 left hand isi/iso standard, carbide tips all size isi/iso standard, h.s.s. tool bit all size isi/iso standard, tapper shank dril all size . isi/iso standard, straight shank dril all size. isi/iso standard, files all size. isi/iso standard, tape set of (3 piece) bsw all size. isi/iso standard, tap set of (3 piece) mm. all size. isi/iso standard, die nut inch/mm all size. isi/iso standard, d. spanner set all size. isi/iso standard, ring spanner set all size. isi/iso standard, box spanner set all size. isi/iso standard, pipe rinch all size. isi/iso standard, measuring tape 3 meter long . isi/iso standard, do - 5 meter long. isi/iso standard, do - 15 meter long. isi/iso standard, tin cutter 10 . isi/iso standard, do - 16 isi/iso standard, revolving centre 3 m.t. isi/iso standard, revolving centre 4 m.t. isi/iso standard, revolving centre 5 m.t. isi/iso standard, oil can capacity 200 m.l. isi/iso standard, screw pitch gauge. isi/iso standard, wooden saw(circular saw)1/8 x 18 isi/iso standard, drill socket (i) size 0 1 isi/iso standard, (ii) size- 1 2 isi/iso standard, (iii) size- 2 3 isi/iso standard, (iv) size- 3 4 isi/iso standard, (v) size- 4 5 isi/iso standard, h.s.s. black tool bar square high grade all size, steel rule 12 . isi/iso standard, steel rule 24 . isi/iso standard, screw driver set all types and sizes. isi/iso standard, pliar all type and sizes. isi/iso standard, drill chuck straight size: 1/8 to isi/iso standard, carbide tips only (all size) isi/iso standard, high carbon steel tool 10% cobalt size: to 1 isi/iso standard, knurling tool multi purpose. isi/iso standard, carbide tip tool (with handle) k-20 for (roller grooving) (i) size- 1, x 12 x 40 isi/iso standard, (ii) size- 1, x 12 x 45 isi/iso standard, (iii) size- 1, x 12 x 50 isi/iso standard

Screw Pitch Gauge Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Central Government And Public Sector

Central Government And Public Sector

Central Government/Public Sector