Get complete information related to latest Self Starter Motor Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Self Starter Motor Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Self Starter Motor Tenders.
Tender For supply of cylinder liner , piston pin end lock , main bearing set , big end bearing , thrust washer , front tiiming cover seal , rear crank shaft oil seal , cam shaft bush , water pump assy , major over hauling gasket with head gasket , fly wheel ring , fly wheel bush , clutch palte , pressure palte , release bering , oil pressuer switch , temparture sending unit , theromastat valve , cam tikki , inlet end exhaust valve seal set , inlet end exhaust valve seat , inlet exhaust valve guide set , fuel line flexi bale pipe with clamp , inlet end exhaust valve , diesel high pressuer line , rear brake shoe set , master cylinder , 13 no bolt , dieselfilter , m oil filter , air filter , 13 no. stud with nut , banjo washer , anna bond tube , old colth , selfstartermotor brush holder , selfstarter bush bearing , selfstarter carbon bush
Tender For providing of consumable material/spares for routine maintenance/ operation of 1000hp/750kw ht slip ring induction motors at tawi pump house, jammu. - providing of carbon brush holder assembly as per sample (an assembly comprises of 6 no. brush holders and 12 nos. carbon brushes of size 32x38x55mm) with tension springs and pin holding slots for different adjustment, having current carrying capacity of 650 amp, fabricated out of gun metal material for fitment to jyoti/ bhel make 1000hp /750kw slip ring induction motor installed at tawi pump house, jammu., providing of spare sets of copper carbon brushes of size 32x38x55mm for 750kw/1000hp, 6.6kv slip ring induction motor (1 set comprises of 12 nos. carbon brushes), providing of rubber bearings for 900 vm-2, 60 cusecs vt pumps as per sample casted out of superior quality rubber finished to the required size having size height 230mm, inner dia. 95 mm and outer dia. 125 mm with proper facing on both ends for proper fitment., ravi canal :- d-18 h/r, dol vijaypur. complete job.
Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging
Tender For supply of self-startermotor assembly 12 volt (lucas tvs) to suit 3 ton godrej fork lift truck model no: gx 300d. part number - 26024613a. [ warranty period: 30 months after the date of delivery ]
Tender For bid to ras supply of selfstartermotor assy , water pressure pipe , o ring seal for membrance , o ring seal for filter large , o ring seal for filter small