Latest sheathing plate Tenders | Government sheathing plate Tenders

State Government

CTN :45483991

30 Jun, 2026 5.50 Lacs

Kangra - Himachal Pradesh

Tender For supply of tata 1613 filter kit cummunis bs-iii fuel filter 252509120239 tata oil filter 27861813902 , filter kit cummunis bs iv fuel filter f002h22095bosch oil filter , air filter element set , pressure plate 352 mm , clutch plate 352 mm , pressure plate 330 mm , clutch release bearing , clutch servo 90 , c m c assy , u j cros , canter bearing with rubber , brake shoe lining set front , brake shoe lining set rear , brake shoe lining set front with rivets , brake shoe lining set rear with rivets siv , fan belt set 8pk 1250 980 , starter motor 26024055a 24v , head light set l r new modal , tail light set l r new modal , solenoid switch 24v , gear box sensor assy , cabin shocker cabin cylinder , cabin hyd pump assy , side indicator set l and r , armature assy 24v bsiii , armature assy 24v bs iv , horn 24 v , 4 pin relay 24v , battery terminal , battery terminal plus , fog light set , head light tube 24v , fly wheel assy with fly ring 138 teeth , hub seal kit front , hub seal kit rear , radiator assy , radiator tank reservoir , radiator hose pipe set , fan belt bsiii , brake booster front wheel , brake booster rear wheel , head gaskket , rear view mirror l r , clutch plate 330 mm dia , chevrolet tavera rear brake shoe rbl 1010 , clutch set 65225050002c , front disc rotor 29390004 , alternator belt xu15 1017 , accelerator cable 3501 , front wheel bearing outer 48548 , front wheel bearing inner 12649 , fuel filter housing t97690400 , fuel filter line , center pin gmf9118 , front shocker am s 700193 , rear shocker am s 700186 , water pump assy wp140 , upper clutch cylinder assy cs541 , lower clutch cylinder assy cs542 , front suspension bush kit vr 1401 , rear bush kit , torsion bar bolt sisco 1422 with nut assy , thermostat valve , water hose pipe clump , wheel cylinder rear mew 2701 , stepny securing assy ci 5716 , hub stud with nut , clutch relase bearing , brake master cylinder with booster , steering coupling , front disc pad taver , front suspension kit major with ball joint tie rod end , shaft cross , center rod tavera , wind shield sefety glass tavera laminator , filter kit oil filter fuel filtr , air filter , wipper set tavera , head light tavera lh new model , haead light tavera rh new model , head light tube 12v , tail light set rh , tail light set lh , horn 12v , starter motor self , mohindra bolero camper gold zx wind shield glass front , mohindra bolero camper gold zx tail light set l r , tata winger ambulance filter kit oil filter , front disc pad , maruti swift dzire 2018 patrol box assy steering gear , maruti swift dzire 2018 patrofront shocker assy set l r

Central Government/Public Sector

CTN :45492829

01 Jul, 2026 NA

Subansiri - Arunachal Pradesh

Tender For supply of vrf or vrv air cooled outdoor units suitable for cooling or heating having 100 percent hermetically sealed inverter type twin rotary or scroll compressor capacity of machines 14 hp to 22 hp , following minimum capacity 4 way vrv or vrf cassette type indoor ceiling mounted unit equipped with synthetic washable media pre filter,3 point 2 tr , following minimum capacity 4 way vrv or vrf cassette type indoor ceiling mounted unit equipped with synthetic washable media pre filter,4 tr , vaccumiazation and nitrogen testing of following nominal sizes of soft or hard drawn copper refrigerant piping for vrv or vrf system, thickness 1 point 2 mm , 9 point 5 mm dia od soft drawn with tube thickness 1 point 2 mm , 12point 7 mm dia od soft drawn with tube thickness 1point 2 mm , 15 point 86 mm dia od soft drawn with tube thickness 1point 2 mm , 19 mm dia od hard drawn with tube thickness 1 point 2 mm , 22 point 2 mm dia od hard drawn with tube thickness 1 point 2 mm , 25 point 4 mm dia od hard drawn with tube thickness 1 point 2 mm , 28 point 58 mm dia od hard drawn with tube thickness 1 point 2 mm , 34 point 9 mm dia od hard drawn with tube thickness 1 point 62 mm , 41 point 27 mm dia od hard drawn with tube thickness 1 point 62 mm , s i t c of y joints kit refrnet , drain piping rigid pvc piping complete with fittings supports as per specifications and insulated with 6mm thick closed cell elastometric nitrile rubber insulation 25mm dia and , 32 mm dia , 40mm dia , control and transmission wiring , testing and commissioning of vrf or vrv systems including topping of r410a gas as per site requirements , supply and installation of u or v protection of used copper pipe at outer site for odu connection site , 6way load bank double door enclosure confirming to is 8623 iec 60439 g frame panel boards , supplying and fixing of following sizes of medium class pvc conduit along with accessories 25mm , frlsh or hffr pvc insulated copper conductor single core cable in the existing surface or recessed steel or pvc conduit as required 3 x 1 point 5 sq mm , suitable size gi box with modular plate and cover in front on surface or in recess , one number xlpe insulated and pvc sheathed copper conductor armoured power cable of 1 point 1 kv grade 4 x 16 sqmm , 16 a rating 240 by 415 v 10 ka c curve miniature circuit breaker suitable for nductive load of following poles in the existing mcb db complete with connections single pole , single pole and neutral sheet steel mcb distribution board 240 v on surface by recess complete 12 way double door , supplying and fixing 25 a rating single pole and neutral , following size of perforated painted with powder coating m s cable trays 150 mm width x 50 mm depth x 1point 6 mm thickness , earthing with g i earth pipe 4 point 5 metre long 40 mm dia including accessories , providing and laying earth connection from earth electrode , providing and fixing 6 swg dia g i wire on surface or in recess for loop earthing , amc as per section c , installation of cassette ac 2 ton 5 star , copper pipe , 4 core copper wire , drain pipe with insulation , odu stand , cable tray , hanging rod , faster nut , wrapping tape , 3 core copper wire

State Government

CTN :45483333

11 Jun, 2026 NA

Mahendragarh-Hr - Haryana

Tender For bhagot block: kanina panchayat: bhagot dist.: mahendragarh annual maintenance work for water supply. - miscellaneous items - iron plate bore, rubber sheet, gi gate valve, nut and bolt , hose pipe, hdpe folding pipe, g. i. nipple, gi tee, iron plate etc..

Central Government/Public Sector

CTN :45479376

29 Jun, 2026 NA

Perambalur - Tamil Nadu

Tender For brushless 110v dc fan 400 mm sweep fixed type to rdso specification no. rdso/pe/spec/tl/0021/2005, (rev.3) with amendment no.1 with stainless steel guard. (1) firm to supply 1 no. each of male connector with cage clamps similar to catalogue no. 721-603 and female connector withcage clamps similar to catalogue no. 721- 103/026-000 of wago (2) clause no.4.11 of the above specification shall be read as paint less stainless steel fan guard crash worthy design shall conform to coil of icf drawing no. icf/sk-7-6-158, alt.h. (3) the colour of the rating plate shall be black. (4) the fan shall be supplied in assembled condition in individual carton box with suitable packing. (5) guard round plate shall have indian railway logo as per rdso/sk/csc-1124a (but maximum dimensions scaled down to 60 mm dia.) and not the name of the manufacturer. (6) rubber packing to icf drawing no. icf/sk 7-3-058 / item-2, alt.e shall be supplied along with fans. (7) the connecting leads shall be 1.5 sq.mm e- beam cable to rdso spec.elrs/spec/elc/0019, rev.4 and 560 mm long, measured from outside the motor body crimped with suitable lug for termination on fly back connector side and fan body side. [ warranty period: 30 months after the date of delivery ] ]

corporations/Associations/Others

CTN :45480167

12 Jun, 2026 NA

Neyveli - Tamil Nadu

Tender For auction sale of condemned iron scrap as per description,condemned alloy steel scrap as per description,condemned rollers and shafts inclusive of rubber lined and cushion rollers scrap,iron scrap as per description,condemned rubber lined conveyor pulley drum scrap,vane beater plate scrap,dozer parts and scrap other items as per description,condemned bucket wheel teeth scrap,iron scrap consisting of auto parts scrap,condemned rusted iron as per description,condemned iron scrap items as per description

State Government

CTN :45478262

13 Jun, 2026 NA

Birbhum - West Bengal

Tender For fixation of local market rate(including gst and cess) for implementation of different scheme under mgnrega at khoyrasole dev. block and 10 nos of gp under khoyrasole dev. block for the year 2026-27 - mgnrega materials, hire charges of concrete mixer 0.25 to 0.40 cum with hopper, hire charges of diesel road roller- 8 to 10 tonne, hire charges of pump set of capacity 4000 litres/hour, vibrator (needle type 40 mm), surface vibrator, water tanker 5000 ltr. capacity, seam bolts and nuts 6 mm dia and 25 mm long, brick aggregate (single size):50 mm nominal size, brick aggregate (single size):40 mm nominal size, stone aggregate(single size):63 mm nominal size, stone aggregate(single size): 40 mm nominal size, stone aggregate(single size):20 mm nominal size, stone aggregate(single size): 10 mm nominal size, stone aggregate(single size): 06 mm nominal size, brick bats, portland cement, white cement, coal (steam), brass 150 mm floor door stopper (0.357 kg), chromium plated brass mortice latch and lock 100x65 mm with 6 levers and a pair of brass lever, glue, unslaked lime, synthetic enamel paint, having voc ( volatile organic compound content less than 150 gm/liitre, ready mixed pink or grey primer on wood work(hard and softwood) having voc content less litrethan 50 gms/litre, water thinnable cement primer for interior wall surface, having voc content less than 50 litre gms/litre, moorum, black japan, synthetic enamel paint in black or chocolate shade, superior copal varnish, green or blue medium shade pigment, rolling shutter made of 80x1.25 mm machine rolled laths, galvanised steel plain sheets, galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots, galvanised steel j or l hooks 8 mm dia, stone dust, g.i limpet washer, bitumen washer, g.i. plain washer for seam bolts, wire mesh (rabbit), diesel oil, mirror of superior make glass 60x45 cm, vitreous china pedestal for wash basin, g.i. pipes 15 mm dia, g.i. pipes 20 mm dia, g.i. pipes 25 mm dia, g.i. pipes 32 mm dia, g.i. pipes 40 mm dia, g.i pipes 50 mm dia, g.i. pipes 65 mm dia, g.i. pipes 80 mm dia, r.c.c. pipes np2 class 250 mm dia, r.c.c. pipes np2 class 300 mm dia, r.c.c. pipes np2 class 450 mm dia, r.c.c. pipes np2 class 600 mm dia, r.c.c. pipes np2 class 900 mm dia metre, r.c.c. pipes np2 class 1000 mm dia, white plastic seat (solid) with lid c.p. brass hinges and rubber buffers, shower rose c.p brass for 15 to 20 mm intel 100 mm dia, vitreous china squatting plate urinal, h.p. or l.p. ball valve with polythene floats: 15 mm dia, h.p. or l.p. ball valve with polythene floats: 20 mm dia, h.p. or l.p. ball valve with polythene floats: 25 mm dia, brass full way valve with c.i. wheel (screwed end) 25 mm dia, vitreous china flat back wash basin 630x450 mm, vitreous china angle back wash basin 400x400 mm, vitreous china foot rests 250x125x25 mm, float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm), float glass sheet of nominla thickness 5.5 mm (weight not less than 13.50 kg/ sqm), float glass sheet of nominal thickness 8 mm (weight not less than 20.00 kg/sqm), anodised aluminium hanging type door stopper, galvanised steel corrugated sheets, vitreous china flat back wash basin 550x400 mm, stainless steel bolts /square bar and plates, mild steel tubes hot finished seamless type, red oxide zinc chromate primer, vitreous china flat back wash basin 450x300 mm, hydraulic door closer tubular type aluminium section body each, oxidised m.s. casement stay (straight peg type) 300 mm not less than 0.33 kg, coloured orissa pattern w.c. pan 580x440 mm, coloured pedestal type w.c. pan 580x440 mm (european type), circular shape 450 mm dia precast r.c.c. manhole cover with frame l.d. -25, upvc pipes (working pressure 4 kg /cm2 ) single socketed pipe 75 mm dia, upvc pipes (working pressure 4 kg / cm2 ) single socketed pipe 110 mm dia, upvc single equal tee (without door) 75x75x75 mm, upvc single equal tee (without door) 110x110x110 mm, upvc single equal te

Central Government / Public Sector

CTN :45471311

15 Jun, 2026 NA

Hyderabad-T - Telangana

Tender For supply of set of upper flange for uic type rubber vestibule conforming to rdso specification no. rdso/2007/cg-05, rev.01. consisting of 8 items s no description rdso drg no. qty./ kit 1 upper flange sk - 99056, alt. 3 , item -2 1 2 rubber packing 6x75x1490 sk - 99056, alt. 3 , item -5 1 3 locking plate sk - 99056, alt. 3 , item -8 1 4 locking plate sk - 99056, alt. 3 , item -9 1 5 hex. head screw m 10 x 50 sk - 99056, alt. 3 , item %u2013 10 10 6 spring washer m 10 sk - 99056, alt. 3 , item -11 19 7 hex nut m 10 (dc) sk - 99056, alt. 3 , item - 12 19 8 csk head screw am10x35 sk - 99056, alt. 3 , item -13 09 [ warranty period: 30 months after the date of delivery ] ]

Central Government And Public Sector

CTN :45486853

22 Jun, 2026 NA

Bangalore - Karnataka

Tender For supply of helical inline gear motor to the model no. sk 973.1 - 112mp/4 tf for axle pusher chain conveyor of make m/s nord or substantially equivalent with following features: input speed(rpm): 1440; output speed(rpm): 21; gear ratio: 68.5; power (kw): 4; service factor: 1.8; output torque: 1817 nm; overhung load: 25 kn; axial load: 22 kn; motor inverter speed range: standard line powered inverter capable; voltage: 400/690 v; frequency: 50 hz; efficiency class: ie3; current 1: 7.85 a; current 2: 4.53 a; cosinus: 0.83; motor duty: s1 - continuous; enclosure: ip55; insulation class - f; mounting pos - m1; housing material: cast iron housing; type of housing: foot mount; output shaft: solid keyed shaft; output shaft (dia x length): 60x120mm; output shaft material: standard; gearbox breather options: auto vent; gearbox sealing options:fkm seals; bearing design: standard bearings; motor cooling: tefc - totally enclosed fan cooled; motor thermal protection: thermistor; motor option: fluoro rubber motor seals; height of output shaft center frombottom of base plate: 225 mm; mounting base plate details: minimum plate thickness: 50 mm; 04 holes of 22 mm dia each with square pattern; distance between holes along the shaft: 310 mm; distance between holes perpendicular to shaft: 250 mm; note: - (i) material of construction: fabricated steel housing (stress relieved) (ii) all gears shall be manufactured from steel forgings or rolled bar made from steel 17cr ni mo6/18cr ni mo6 (case hardening steel). (iii) all gears shall be case hardened to 58-62 hrc and profile ground. (iv) output shaft shall be of en 9 material normalized to 201 bhn (min) (v) bearing used shall be rolling element type of make skf/ntn/timken/fag only. special conditions: above specified materials are the minimum required standard to be considered while designing the gear motor. [ warranty period: 18 months after the date of delivery ] ]

CTN :45483287

19 Jun, 2026 NA

Lalitpur - Uttar Pradesh

Tender For supply of oil seal , bulb 12v 55w , pvc pipe dia 40 7401g , pipe assy , repair kit spring brake actuator t 20 24 , bearing ball annualar , chain silent , propeller sprocket hub , part kit brake chamber , t d poston , cam plate , nozzle , filter element , wiper gear , screen oil filter , valve comp float , gasket cylinder head , brake shoe front , brake shoe assy , tank water reserve , spring pad , rubber hose aux w tank to fill pipe

CTN :45484687

18 Jun, 2026 NA

East Khasi Hills - Meghalaya

Tender For supply of cp kitchen sink mixer prayag , wire mesh 0.56 mm 15 mtr each roll , kitchen plate rack ssteel 31inch x 30inch , fancy curtain rod 3 mtr , fancy curtain bracket , center hole basin mixer without popup cp , hydraulic door closer , front glass shelves 500x125mm , bracket for curtain rod long neck , tower bolt alu 200 mm , ss wire mesh 0.36 mm dia 15mtr each roll 1.40 mm apreture , tower bolt alu 150 mm ipssa , glass pane 2ft x 4ft x 4mm frosted glass , kitchen sink stainless steel 940x 460x 203mm bowl size 405x 354x 203mm with drain board , door seal bottom, door air gap rubber shield 36inch x 93 cm, anti rust, brown colour, black rubber , glass panes 2ft x 4ft x3mm clear glass , m seal in 1 kg pack , helical door spring ipssa , sliding door bolt alu 250 mm ipssa , mortrise lock brass godrej , c p waste coupling 32 mm for sink. , tower bolt ssteel 150 mm ipssa , cp grating rectangle slots with round grating at middle 150x150mm , cp grating 100mm dia with one big hole , waste coupling for sink 32 mm , sliding door bolt ms 300 mm ipssa , curtain rod 19 oblique 20mm 3mtr long , kitchen sink 610mm x 460mm x 203mm bowl size 560mm x 405mm x 203mm , cp grating 100mm dia with normal hole , tower bolt alu 100 mm ipssa , kitchen sink bowl size 560mm x 405mm x 203mm , butt hinges 100 mm , bow handle alu 100 mm ipssa , sliding door bolt alu 300 mm , bow handle 150 mm alu ipssa , teflon ptfe tape roll thread seal tape , nut and bolt for steel window for fixing of wire mesh , butt hinges 75 mm , brass sliding bolt 200mm , bow handle 200 mm alu ipssa , decorative curtain rod finials wooden , cp grating 100mm dia with rectangle slots , brass tower bolt 100mm , brass bow handle 100mm , door stopper alu prayag , hasp and staple c p 100 mm ipssa , alu handle 125mm ipssa , hasp and staple cp 75mm //bid details 2 / 40

Sheathing Plate Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors