Tender For supply of electric slaughterhouse (for animals) - primary & secondary chamber primary chamber* single chmber furnace of size 4270 mm x 1980 mm x 1820 mm.* plate thickness- 5 to 8 mm.* lining of interior of furnace- 400 mm wall cermaic blanketk, high aluminia refractory brick is-8-1994 line with insulation brick is 2042-2006* operation temperature- 800o c to 1000o c.* top smoke discharge for secondary chamber.* ash removal doors to be provided for ash collection after combustion.* ingtion- automatic.* temperature control- automatic* material loading- front gate- automaticsecondary chamber* operating temperature - 1050o c to 1250o c.* material of construction- mild steel with high aluminia refractory brick is-8-1994 line with insulation brick is 2042-2006.* made from is 2062 grade mild steel materials (or better) duty lined with insulation bricks, refractory bricks, hysil boards.* burner mounting arrangement with refractory burner block.furnace door:furnace door charging & discharging side fabricated from 5mm to 6 mm thickness door opening & closing automatic.ash door:* ash door (with casted cement lining) to remove nonhazardous ash from the chamber.* top inlet bottom smoke discharge for longer gas residence time.* furnace door charging & discharging side fabricated from 5mm to 6 mm thickness.* door opening & closing automatic/manual.refractory:{complete set of refractory shaped bricks for construction electric cremation of i.s. 8 bricks (approx. 1007nos bricks,insulation 4000 nos. refractory slid for construction of flue duct , as required, refractory heat resistant fire clay , ceramic blanket hysil board, asbestos ropes etc. as required for outer side of the furnace shall be constructed by red bricks by sand and cement as mortars and construction of chimney from basement of roof level including painting i.e. bricks portion shall be painted by two coats of red oxide as primer and to coats of synthetic enamel. (a) complete lining & assembling of entire cremation chamber according to standard size with proper arrangement of accommodation of heating elements, resting of dead body with sufficient opening for falling of ashes to the ash chamber & sufficient ventilation for fresh air spraying. (b) complete lining and assembling of entire cremation chamber according to standard size with provision of drawing out aces from the rear side and sufficient ventilation for fresh air injection. complete lining and assembling of entire cremation chamber according to the standard size with provision of air inlet supplying by fresh air blower and arrangement of multi ventilation path for fresh air}. osspl make, thermocouple heat sensor supply & fixing the thermocouple of heat sensing range 0 - 1200 c (cr.-al) sensor housed in s.s 304 casing of dimension 1200 mm long 22 mm od complete encased to and fitted terminal on other and for connection of compensating of 2 cores 0.5 aq. mm cr- al for heat sensing from thermocouple to temperature controller covered with asbestos embedded rope about 50 m length as per direction of eic., f.d. fan/centrifugal air blower with electric motor * supply and delivery at site, installation, testing and commissioing.* of fresh air injection system forced draft fan mild steel.* type: centrifugal.* capacity:- 500 cmh.* pressure:- 220 mmwg.* motor rating:- 2hp (kirloskar/crompton), burner assembly * total 2 nos. of lpg/cng/png fired automatic burner required.* the burner should be provided with comprising diffuser plate/ burner plate, photo cell housing electrodes with holding brackets, solenoid valve, electrodes caps, flexible hose pipes, spary nozzles, oil filter, blower, etc. connected with electric motor (each burner) & in built air regulator.* burners will work on auto on/off as per the set temperature for the combustion chambers.* the in-built bolwer will provide continuous air flow to the burners to prevent demages due to high temperature., supply and fixing of manifold with a p
Tender For supply of ventilation fan motor (foot mounted induction motor) for lhb power car of rating 5kw, 415vac, 3 phase, 50hz, 1500 rpm (synchronous speed), ip65, insulation class-h, dutys1, conforming to is:12615 (2011) or latest. the motor should be m/s abb, mis laxmi hydraulic, m/s crompton, m/s siemens, m/s kirlosker electric make only. as per make mentioned at rdso's specification no. roso/pe/spec/ac/0084-2008, rev.1. [ warranty period: 30 months after the date of delivery ]
Tender For procurement of spares for hea (high energy arc) igniters installed in boilers of both units at stpp, jaipur, mancherial, telangana. - roof bolts, m.s. bolts & nuts, rivets, washers & screws, dog nails, fish plates, nuts & bolts for fish plates, belt jointing pins, cable hooks and signal hooks, belt conveyor rollers, belt sections, resin capsules, cement capsules, gi canisters, blasting gallery – spacers, radiator repairs, repairs and rewinding of motors of ac & dc, repairs / rewinding of transformers (welding / lighting/ power), gi wire, wire mesh for longwall salvage, manufacturing of supply of electrical coils for, i) ac motors up to 6.6 kv grade, ii) transformer coils up to 33 kv grade, repairs of rotors for electric motor, lighting cable, steel chock manufacturing, house wiring, all types of fan repairs, shovel bucket welding, repairs of pumps, couplings manufacturing, special steel and alloy castings (tooth points, track pads, mn steel, casting), manufacturing of fly ash bricks. (not to be manufactured at stores site. it, shall be at their own site)., manufacturing of pump components (spares)., transformer oil filtration, reconditioning of drill bits and drill rods, vulcanizing the old trailing cables of drill machines, sdls, lhds, etc., work should be carried out at the respective mine premises)., manufacturing of earth clamps, g.i flats, g.i bolts and nuts., crimping of hydraulic hoses., repairs to hydraulic pumps, motors, control valves and other related, components, refurbishing of lt & ht switches with oem spares including testing., manufacturing / repairs of sliprings & d-contacts., furniture repairs i.e., cane chairs, table, almirahs, etc., repairs to wet grinders, water purifiers, and water coolers, manufacturing of coupling bolts of all sizes, fabrication of oht line components like cross arms, clamps, stay wires,, cross brassings, base plates etc., manufacturing of haulage rope drum rollers., all sizes of ventilation doors., safety boards designing/stickering/painting with retro-reflective radium, papers/paint on hemm/radium stickering in underground & surface,, radium boards, safety boards & radium jackets, fabrication of lighting & cable cross over towers, maintenance & repairs of air conditioners on hemm, painting work in underground and on surface, fabrication and erection of ms structural works like gantry, bunker etc., tailoring works at hospitals & area workshops, manufacturing of hume pipes, clay pills manufacturing, maintenance of pmts/lighting transformers/power transformers & substations, erection/renovation of residential/pmts/sb-station earth pits, (conventional type/chemical type), testing of all protective relays & mprs, tub assembling/repairing of coal tubs in mines, ci casting works like ci pulley, tub wheels, outsourcing works in mines, like masonary walls construction, surface, material loading, cleaning and dusting in underground etc., all types of computer software installation, antivirus, hardware and, network installation., cc cameras installation and repairs.