Get complete information related to latest Sludge Valve Repair Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Sludge Valve Repair Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Sludge Valve Repair Tenders.
Tender For supply of piston with piston pin , piston ring , cylinder sleeve , engine overhauling gasket complete , main bearing set , big end bearing set , crank thrust washer , oil seal engine rear , oil seal oil pump , o ring oil seal , o ring distributor housing , water pump assy , fly wheel with ring ger , input shaft bearing , clutch release bearing , clutch plate , clutch cover assy , timing cover with seal , oil sending unit , temperature sending unit , valve inlet and exhaust , valve oil seal inlet and exhaust , cotter valve , valve seat inlet and exhaust , valve guide inlet and exhaust , rocker arm shaft , rocker arm mounting screw , cam shaft oil seal , spark plug , suspension bush set complete , engine mounting lh and rh , fan belt , carburetor assy , chock cable carburetor , worm hose , fuel pipe rubber , rubber hose air cleaner to carburettor , parking brake liver assy , cable set parking brake , wheel cylinder rear lh and rh , fuel tank rubber hose , front brake calliper rubber pipe , thermostat valve , 10 mm bolt half inch with nut , 10 mm bolt one inch with nut , 12 mm bolt with nuts one and half inch , steering shocker , solenoid switch of self starter , self starter carbon bush , mounting bolt 12 no , nut 12 no , ignition coil , horn relay 12 volt , t horn high and low bid number/ & ( * ) : gem/2025/b/6283168 dated/ + : 29-05-2025 bid document/ 2 2 1 / 40
Tender For supply of spares - oil valve kit part no-24063058 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , thermostat kit part no-24063114 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , piston ring kit part no-22222394 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , main bearing kit std pos-2,4,6 part no-23573146 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , main bearing kit std pos-1,3,5,7 part no-23573147 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , thrust washer kit std-a part no-21908099 for repairing of engine, modeltad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , thrust washer kit std-b part no-21908101 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , seal crank shaft rear part no-21877169 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , seal crank shaft front part no22731065 for repairing of engine, model-tad851ve, makevolvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , gasket cylinder head part no-22722746 for repairing of engine, modeltad851ve, make-volvo penta suitable to similar esn 3008602532 and 3008602529 fitted along with lhd 907 , valve cover gasket part no-21717748 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , gasket rocker cover part no-21717753 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , oil filter cap part no-23593794 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , oil pump part no-22015568 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , gasket part no-21838299 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , sump gasket part no-21492627 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , gasket part no-24075099 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , gasket inlet manifold part no-21859203 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , turbocharger part no-23099979 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn-3008602532 and 3008602529 fitted along with lhd 907 , gasket part no-21615788 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , gasket part no-22206133 for repairing of engine, modeltad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , gasket part no-20707685 for repairing of engine, modeltad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , thermostat part no-21746213 for repairing of engine, model-tad851ve, make-volvo penta suitable to similar esn3008602532 and 3008602529 fitted along with lhd 907 , gasket part no-21796165 for repairing of engine, modeltad851ve, make-volvo penta suitable to simil
Tender For corrigendum : supply of w96716155910 drg: 31611770098 rev: 00 condenser air evacuation package (vacuum pump) 30scfm , w96716155317 drg: - rev: 00 complete vacuum pump (bare shaft vacuum pump) spec: he57016 rev: 04 , w96716155325 main motor for vacuum pump spec: he57016 rev: 04 , w97716155067 bearing for motor of vacuum pump (30 scfm) (1set= 2nos) spec: he57016 rev: 04 size: to s , w97716155822 pressure transmitter for vacuum pump system: 0-1 bar abs spec: he57016 rev: 04 , w96716155813 level transmitter for vacuum pump spec: he57016 rev: 04 , w96716155244 drg: 31611770051 rev: 00 temperature transmitter for vacuum pump spec: he57016 rev: 04 , w96716155210 drg: 31611770047 rev: 00 differential pressure switch for vacuum pump. spec: he57016 rev , w96716155490 flow indicator cum switch for vacuum pump spec: he57016 rev: 04 , w97716155466 temperature gauge 0-100 deg c, for vacuum pump heat exchanger size: 0 to 100 deg c , w97716155733 drg: to suit original supply rev: 00 pressure gauge (0 to -1 bar) , w97716155741 drg: to suit original supply rev: 00 pressure gauge (service water) , w97716155547 level gauge for vacuum pump separator tank spec: he57016 rev: 04 size: to suit original , w96716155457 differential pressure gauge for vacuum pump package duplex filter spec: he57016 rev: 04 , w97716155849 drg: to suit original supply rev: 00 air flow meter (rotameter) for vacuum pump system s , w97716155679 complete solenoid valve assembly for air control system (process inlet) spec: he57016 r , w97716155660 complete solenoid valve assembly for seal water make-up spec: he57016 rev: 04 , supervision of commissioning lump sum per man day charges at site, including every expense at our si , supervision of commissioning lump sum per visit charges (to &fro) including travelling time & all ex
Tender For supply of rubber molded goods - moulded rubber goods, neoprene rubber square suitable to stand temp.200 c for juice heater size 5/8 x 5/8 , rubber square suitable to stand temp.200 c for v. line juice heater size 1/2" x 1/2", nitrile rubber seat for angle valve of juice heater suitable to stand temp.200 c, as per drg no. ksc/bh/296/02, nitrile rubber seat for double beat valve of juice heater size 240mm od x 94mm bore x 18 mm thick, neoprene rubber taper plug for evaporator tubesize: 37mm x 40mm as per drg.no. ksc/286/02, nitrile rubber seat for vapour angle valve (inlet of 4th evaporator body) suitable to stand at 200 c temp. as per drg.no.ksc/evp/97/2001 fig no.1, nitrile rubber seat for main exhaust valve of semi kestner as per our drawing no. ksc/bh/7898 fig. no. 1, nitrile rubber seat for surplus exhaust angle valve of semi kestner suitable to stand at 280 c as per drg. no.ksc/bh/7899 fig no. 3, nitrile rubber seat for outlet vapur valve of s.k. suitable to stand at 280 c as per drg. no. ksc/bh/7899 fig.-1, nitrile rubber seat for angle valve (inlet exhaust valve of v.cell) suitable to stand at 280 c as per drg. no. ksc/bh/8607 fig.-1, nitrile rubber seat for pan exhaust valve to stand at 260 c as per drg.no.ksc/bh/7899 fig no. 2, nitrile rubber seat for exhaust/vapour angle valve for pan no. 1, 3, 8 & 10 as per dr g. no. ksc/boil/221, fig. no. 1, fig. no. 2, fig. no. 3, fig. no. 4, nitrile rubber seat for discharge valve of pan no. 1 to 5 as per drg. no.ksc/bh/8607 fig.-2, nitrile rubber seat for discharge valve of pan no. 6 & 7 as per drg. no.ksc/8608, nitrile rubber seat for discharge valve of pan no. 9 & 10 as per drg. no.ksc/8609, synthetic rubber joint for main hole of pan 3, 4 & 5 size 517 od x 443 bore x 13 thick., synthetic rubber joint for main hole of pan 1, 2, 3,6, 7, 8, 9 & 10 size 26" od 12" bore 6 mm thick, synthetic rubber joint for pan condenser main hole (a) size 22"od, 12"bore, 6mm thick,, (b) 28"od,12"bore, 6mm thick, synthetic rubber joint for evaporator man hole od 19.11/16 bore 18. 7/16 & 5/8" thick, nitrile rubber seat for double beat valve of juice heatersize 240 mm od x 94 mm bore x 21 mm thick, nitrile rubber seat for double beat valve of juice heatersize 230 mm od x 94 mm bore x 21 mm thick, synthetic rubber ring suitable to stand at 150 ctemp. & 200 psi dia(inch.) bore(inch) thickness(mm), 24 12 6, 26 12 6, 28 12 6, 30 12 6, 36 18 6, 48 40 6, 54 46 6, synthetic rubber ring joint suitable to stand at 150 c temp. and 200 psi for sight glasses of pan & evaporator dia(mm.) bore(mm) thickness(mm), 230 180 6, 220 180 6, 210 165 2, 222 195 2, 218 190 2, 170 130 6, 150 110 6, neoprene rubber star for cane un-loader as per drg.no.ksc/cr/311286 size : 6", neoprene rubber star for cane un-loader as per drg.no.ksc/cr/17982 size : 9", rubber bushes, o.d.(inch) bore(inch) length(inch), 5/8 1, 7/8 1, 1 1, 1.1/4 1/2 1.1/2, 1.1/4 5/8 1, 1.1/4 1.1/4, 1.1/4 7/8 2, 1.1/2 1.1/4, 1.1/2 1.1/2, 1.1/2 7/8 1.3/4, 2 2, 2 7/8 2, 2 1 2, 2 1.1/2 7/8, 1 1/2" 3/4" 2", 2.1/2 1.1/4 2.1/2, 1 1/2 1, 1 1/2 1 1/4, 1 1/4 5/8 1 1/2, 1 1/4 3/4 1 1/2, 1 1/4 1/2 1 1/4, 1 1/2 3/4 2, 1/2 3/4 2, 1/2 5/8 1 1/2, spares for t.e.w. make type 36 dia juice clarifier, mud sealing ring as per sample/ drg., telescopic valve rubber ring as per sample/ drg., mud scraping rubber strip with wire netting size 32" x 5" x ", rubber seat for molasses weighing scale size- 14 dia, thickness- 16mm type ( silicon bitile rock hard rubber ), (a) rubber seat for water weighing scale (as per drawing ), (b) rubber seat for juice weighing scale (as per drawing ), neoprene rubber stoper(hard quality) for juice weighing scale 70/62 dia, 55 mm lenth as per drawing no-ksc/jk1/144, neopreme rubber seat for exhaust valve suitable for 200 0 c temerature as per drawing no : ksc/bh/1021, serial no 1 , od 510, id 365 mmthickness 40/15 mm, serial no 2 , od 555, id 380 mmthickness 40/15 mm, serial no 3 , od 655, id 480 mmthickness 40/15 mm, seri
Tender For supply of gear selector fork for 2.5 ton tata , gear selector shaft for 2.5 ton tata , gear box top bearing for 2.5 ton tata , gear box top out oil seal for 2.5 ton tata , gear box top plate with bolt for 2.5 ton tata , cluth pipe for 2.5 ton tata , bleeding nut for 2.5 ton tata , brake booster for 2.5 ton tata , pressure pipe for 2.5 ton tata , hand brake booster for 2.5 ton tata , bumper spring for maruti gypsy , thermostat valve seal for maruti gypsy , radiator hose inlet for maruti gypsy , s a hose tank pump for maruti gypsy , radiator hose outlet for maruti gypsy , steering hose pipe for als , center bolt for als , shackle pin for als , shackle bush for als , main leaf for als , star plate led light for m and m scorpio , inner brg bp for m and m rakshak , outer brg bp for m and m rakshak , oil seal bp for m and m rakshak , drive shaft lh bp for m and m rakshak bid number/ & ( * ) : gem/2025/b/6292035 dated/ + : 30-05-2025 bid document/ 2 2 1 / 20
Tender For supply of maj rep kit air comp , eng mounting pad , damping pad , valve assy solenoid , starter kit , knuckle brg , compressor ring , compressor gasket , clutch master cylinder , clutch slave cylinder , solenoid , sensor inlet air temperature , door lock , clutch centre and back plate assy , lock assy gate side lh , needle roller brg , piston kit master cylinder , bearing input shaft , fuel pump motor , solenoid valve for diff
Tender For supply of tank coolant vehicular - tank coolant , radiator assy , gear change lever , gear lever shaft , inlet valve , cylinder head gasket , cam chain kit , oil seal , cylinder block kit , brake dise , low and high relay , drive assy