Get complete information related to latest Sodium Bulb Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Sodium Bulb Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Sodium Bulb Tenders.
Tender For providing and fixing of various electrical accessories at district and session court metro jodhpur - sitc of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminium housing with in built driver , system lumen efficacy 110 lm/watt output only at cw (5700k to 6500k) , internal surge protection of 4.0 kv with short & open circuit protection ,thd 10% , p. f. 0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000 k / 4000 k / 5700 k /6000 k/6500 k (as per ansi bin) as required., 1170mm(+/-10%) led batten with min. lumen output 2200 lm, sitc of ip-20 led recessed / surface mounted, round / square backlit & smd mid power led downlight with power coated die-cast aluminum housing with uv stabilized non yellowish diffuser with bis compliance 4.0 kv surge protected isolated driver, with short & open circuit protection input 320vac-48 hr protection, input 350vac-2 hr protection), having efficiency > 85% . system lumen efficacy of 110 lm / watt,at cw (5700k to 6500k) , thd 10 % , pf. 0.95, cri >80, life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000 k / 4000 k/ 5700 k /6000 k/6500 k (as per ansi bin) as required., recessed mounting, minimum lumen output 1950 lm, sitc of ip20, 2x2 led surface/ recessed mounting backlit & smd mid power type led light fixture not less than 35 mm housing depth made from crca sheet steel housing, high purity / transmissivity uv stabilized non -yellowish diffuser for uniform light distribution. operating voltage range 140-285 v, hv cutoff - lv cutoff should be 300-100v . high efficiency with 4 kv internal surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( input 320vac-48 hoursprotection,input 350vac-2 hours protection) (integral with light fixture). system lumen efficacy of 120 lm/watt ,thd 10 % , p.f. 0.95,cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000 k / 4000 k / 5700 k /6000 k/6500 k (as per ansi bin) as required., recessed mounting, minimum lumen output 4320 lm, providing & fixing of bee star rated copper wounded with class of insulation f, double ball bearing capacitor start, aluminium body & aluminium blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 with down rod up to 30 cm with secondary support safety cable ( steel rope) , cotter pin, shackle kit with 3 x 1.5 sq.mm pvc insulated flexible copper conductor and making connection testing etc. as required., 1200 mm sweep bee 1 star rated (service value >=4.0 to 4.5 ), providing & fixing of ventilating fans capacitor start, copper wounded, single phase with pvc impeller, abs body, automatic openable louver shutter in existing opening including making connection, testing etc. as required., 200 mm sweep minimum air delivery 450 cum / hour, providing & fixing of 450 mm sweep oscillating type wall mounting / pedestal type fans with three speed, on and off position, sintered iron bush oil impregnated, with metal front and back 120 or more ribs guard; three no. aluminium blades, minimum air delivery 100 cum. / minute , minimum service value 1.11 cum./min/watt, noise level should be = 75 db, power consumption = 120 watts, motor protection through thermal overload protection device, including fixing with anchor bolts, making connection testing etc. as required., wall mounting type with adjustable vertical angle, supplying and laying fr pvc insulated & unsheathed flexible copper conductor of following nominal sizes with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from copper, stranding in acc. to is:8130/iec 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation pvc type a/c/d , flame retardant as per is 10810-53, better amperage rat
Tender For supply, installation, testing and commissioning of phase wire and street light and vairious electrical equipment needed for implementation of budget announcement 2025-26 - providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with uv stabilized pc (uv stablization report submitted for uv cover ) /toughened glass cover and secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm/ wt and potted driver & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driver efficiency >85% ,thd(i) 70 and cct 5700k +355k. surge protection shall be min 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in, led street light fixture with minimum lumen output 5600 lm, sitc of ip-42 and general construction confirming to is:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-(a)thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided(b)complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam/ neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.[c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra )(d)wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap-offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.(e)all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be point to point (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.(f)floor mounted panel sh
Tender For renovation with addition & alteration to e.i. of campus security light along the boundary wall, decoration of front side garden and replacement of decorative light fixture with some decorative poles around the main building in the permises of raj bhawan, patna, bihar.
Tender For supply of led luminaire for floodlight conforming to is 10322 (part 5/section 5) (v3) (under bis scheme - ii) (q2) , led luminaire for road and street lights conforming to is 10322 (part 5/section 3) (v3) (under bis scheme - ii) (q2) , led well glass fixture (v2) (under bis scheme - ii) (q2) , led luminaire (recessed luminaire) (ceiling light) conforming to is 10322 (part 5/section 2) (v4) (under bis scheme - ii) (q2)
Tender For supply and fixing of high mast light material at mia alwar - providing & fixing of ik08 ip-66 protected high power led flood light system with single piece pressure diecast aluminium housing, toughened glass diffuser with suitable lenses on led to achieve various beam angles, of high power led of 3 to 5 watt each . integrated potted driver as a unique bis r number having efficiency more than 85 % and in compliance to bis certified and trade mark certificate. the system level luminaire efficacy >=125 lm/ wt. led driver input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety .power factor >0.95 , thd(i) 10% , driver current =750ma. driver should be phase to phase protection of 440 v for 4 hrs. electrical connector , surge protection min >=4kv internal and 10kv external but inside driver compartment, system life of 50000 burning hours with 70% of initial lumens maintained, cri>70 and cct 5700k 355k. manufactures word mark/name engraved/embossing/screen printing on die cast housing to allow traceability/authenticity. fixture shall be is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr ., high power led flood light minimum lumen output 14800 lm
Tender For nvitation of rates for procurement of electrical materials for the financial year 2026.27 - invitation of rates for procurement of electrical materials for the financial year 2026 27, bakelite pendent holder simple, anchor bulb batten holder, 9w led bulb, 18w led bulb, 23w led bulb, 30w led bulb, t5 holder, t5 rod, led tube rod 18/20/22w integral type, 900va inverter, 150ah battery, ceiling fan 1200 mm sweep, cooler fan 450 mm with vertical pump, rinch tapariya make, pana tapariya make, pliers tapariya make, screwdriver and nut driver, wire stripper, multimeter, high mast timer reknowned make, high mast mcb 63a, change over 63a, office bell radio frequency with remote, room heater 1500 watt blower type, room heater 1500 watt reflector type, tape roll steel grip, fixture clamp with nut bolt 3 foot length, led fixture 45w, led fixture 60w, led fixture 90w, flood light 200w, flood light 250w, sodium vapour fixture 150w complete, sodium vapour choke 150w, sodium vapour bulb 150w, ts sevar light chock, sodium chaouk, 1.5 mm aluminium wire, sodium vapour ignitor 150w, sodium vapour condenser 150w
Tender For supply of electrical materials for the operation and maintenance of technopark phase-iii campus - led light/light fixture, led polycarbonate tube light, led recessed panel light, led street light, led flood light, 6 a, 16 a modular socket, module plates, pvc surface box switch gears (mcb, isolator, rccb, rcbo etc.), 6 a,3 pin plug top, pvc conduit pipe, pvc insulated wires, motion sensor