Tender For bid to ras bid to ras corrigendum : supply of mat. code: w90418113033motorized temperature control valve for cold gas for singarauli, koderma, sipat , material code: w90418113041 motorized temperature control valve for primary water , material code: w90418113068 position transmitter for cold gas temp cntl valve , material code: w90418113076 position transmitter for prima ry water temperature control valve , material code: w90418113025 actuator for cold gas temp control valve , material code: w90415208017 actuator for primary water temp control valve
Tender For purchase of fire safety and fighting laboratory equipment for fts department - purchase of fire safety and fighting laboratory equipment for fts department, cleveland open cup (coc) apparatus standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 c per minute (as per standard) temperature range: (-6 to 400) c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valve body: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hzsafety: overheat protection heat insulation, pensky-martens closed cup apparatus standard compliance: astm d93 / is 1448 (part 21) type: pensky-martens closed cup (motorized, digital type preferred) test cup: brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system: heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustableignition:pilot flame with automatic shutter mechanismtemperature measurement:thermometer or digital sensor (ip-28c or astm)digital temperature displaypower supply:230v ac, 50 hzsafety: over-temperature cut-off flame safety control
Tender For annual work contract for annual, routine and breakdown electrical maintenance works of motorized valve / damper actuators ,soot blowers and edg (excluding chp) 2x660 mw csctpp, chhabra
Tender For procurement of miscellaneous spares for mounting various actuators, solenoids, air limit switches, set of o-ring -- system ggsstp, ropar tender enquiry - grub screw with nut (ht) for mounting pd-28 actuator. size 10x40nim, nut bolt (ht) for mx-450 and cylinder body. size8x25 mm, dowel pin (ht for lock air cylinder assembly. size 10x50 mam, l-key bolt (cs) for air limit switch and cylinder. size 6x40mm., cylinder lock of esp and pd-15(cs). id-20mm and thickness imm, l-key bolt(cs) to lock the stopper of cylinder. size 6x30mm, actuator lock pd-28(cs), id-23mm and thickness-imm, actuator lock pd-50, pd-75 and cylinder lock of apη ducts(cs) id-33mm and thickness imm, l-key bolt for cylinder.6x40mm, screw with nut for mounting pressure switch. size(cs) 3x40mm., grub screw for mounting pd-50 & pd-75. size 12x50mm, nut-bolt(cs) for mounting electrical limit switch (4 to 7 fields). size 4x50mm., grub screw with nut (cs) for mounting electrical limit switches of pd-28, pd-50 & pd-75.size 4x25mm, nut bolt(cs) for mounting solenoids. suze 3x35mm, l-key bolt for air limit switch. size 3x40mm., l-key bolt(cs) for air limit switch. size 3x200mm, nut bolt (ht) for air limit switch. size 12x50mm., l-key bolt for air limit switch. size 4x35mm, l-key bolt(cs) for air limit switch. size 4x20mm, cylinder pin. drawing as perannexure-7, quick exhaust valve diaphragm of size 65mmdiameter thickness-2mm, material synthetic rubber, air limit switch o-ring of synthetic rubber., set consists of, size id-hom., thickness 2mm, 1.size: id = 1 , thickness 2mm, hsn code 40169320, screw with nutcs) 4x25 mm, nut-bolt (h.t) 12x25 for mounting mx-450, cylinder pin (160x250mm), drawing as per annex.-4, nut-bolt(h.t) 10x35 for coupling mx-450, l-key bolt(cs)(6x70mm) for poppet valve., diaphragm for quick exhaust valve diameter 6.5mm &thickness imm., cylinder spacer lock. drawing as per annex-2, stud for pd-28 mounting(10x12mm diameter-25 x40mm length(grub screw), stud(cs) for pd-50 and pd-75 mounting(12x14mm) diameter-10&75mm, stad gir pd-15 mounting(8x10mm) diameter-10x45mm length, hex nipple w(brass), hex nipple w"(ss), hex nipple "x3/4"(85), blow valve cup washer 100 nb drawing as per annex-6., blow valve disc 100 nb drawing as per annex-5, blow valve cup washer 50 nb. drawing as per annex.-1., blow valve disc 50 nb drawing as per annex.-3, stud with nun (cs) (8x35 mm) and overall 50mm length., vent filter sol viv top plate, drgas per annexure-8, solenoidvalve rotex make" model 51400-6-20, solenoidvalverepair kit
Tender For annual work contract for annual, routine and breakdown electrical maintenance works of motorized valve / damper actuators ,soot blowers and edg (excluding chp)2x660 mw csctpp, chhabra