Latest spark plasma sintering equipment Tenders | Government spark plasma sintering equipment Tenders

Central Government/Public Sector

CTN :45263257

23 Jun, 2026 NA

Delhi - Delhi

Tender For supply of uhv deposition chamber - uhv chamber specification (vacuum better than 2 10-9 mbar uhv) chamber overview spherical (diameter 14 ) or equivalent square shaped uhv chamber with support frame equipped with three (3) x 2-inch magnetron sputtering sources. all cf flanges and uhv viewports/ss blanks, three (3) x 2-inch magnetron sputtering sources. each sputtering source has an individual gas inlet line for process gases. all cf flanges., substrate holder : diameter: 2 inches; heating molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature to 1000 c without rotation. rotation: substrate holder can rotate continuously, driven by a stepper motor. variable speed from 0 to 10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to the substrate surface, tilt adjustable. two sputtering sources mounted confocally at an angle relative to the substrate. base pressure: lower than 2 10 mbar (ultra-high vacuum)., vacuum pumping system: turbo molecular pump: pfeiffer hipace300 / edwards next 300 / leybold turbovac 350i with cf100 flange or equivalent with integrated controller, ion pump with controller: included to maintain uhv vacuum levels and provide clean pumping., backing pump: pfeiffer hiscroll 12 / edwards nxds 15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves : one cf100 and one cf150 manual gate valves for isolating the chamber from the pumping systems as well as throttling, vacuum gauges and measurement: one cold cathode gauge with readout capable of measuring vacuum pressures down to1 10-10 mbar for precise uhv monitoring., one capacitance manometer gauge with measurement range from 1 10-1 to 1 10 mbar for accurate pressure reading during deposition phase, gas delivery system: two independent mass flow controllers (mfcs):a. one mfc (0-100 sccm) for argon gas feeding to all three sputtering sources via high vacuum valves.b. one mfc (0-100 sccm) for nitrogen gas feeding directly into the chamber with its own high vacuum valve.gas lines for ar and n2 are physically separated to avoid cross-contamination., chamber access and viewports: 1. two view ports installed on the chamber, each equipped with manual shutters. 2. access ports for gauges, pump, gas inlet and few spares for future upgradation., baking capability: entire chamber designed to bake-out at 150 c to reduce contamination and out gassing during operation, cooling capability : water manifold with flow switch / flow meters, near uhv chamber specification: chamber overview: spherical (diameter 14 ) or equivalent square shaped uhv chamber with stand., three 2-inch magnetron sputtering sources, each with individual gas inlet. all cf flanges and uhv viewports/ss blanks., substrate holder: a. diameter: 2inches; heating : molybdenum heater capable of heating substrate (a) from room temperature (rt) to 800 c during rotation and (b) from room temperature (rt) to 1000 c without rotation b. rotation : substrate holder driven by stepper motor. variable speed from 0 to10 rpmmovement: up / down vertical movement of total 25mm to adjust substrate position during deposition sputtering geometry: one sputtering source mounted parallel to substrate surface (tilt able preferred). two sputtering sources mounted confocally at an angle. base pressure : lower than 5 10 mbar (near uhv)., vacuum pumping system: turbo molecular pump : pfeiffer hipace 700 / edwards next 730 / leybold turbo vac 900 ix or equivalent with cf100 flange and integrated controller, suitable for near uhv vacuum., backing pump: pfeiffer hi scroll 12/edwards nxds15i / leybold scroll vac 15 plus or equivalent dry scroll pump used to back tmp, gate valves: one cf150 manual gate valve to isolate / throttle chamber from pumping system, vacuum gauges and measurement: cold cathode readout capable of dis

corporations/Associations/Others

CTN :45326612

29 May, 2026 20.00 Lacs

Tirunelveli - Tamil Nadu

Tender For sale of condemned scrap materials - ts001-cond.all types of air filters etc.,, ts002-cond.iron all types of clutch disc (ley & tata), ts003-cond.all types of water seperators & stainers etc.,, ts004-cond.polythene papers,plastics and gunny bags etc.,, ts005-cond.all types of (rexins,seat cushions, rubbers,filter,plastic parts, hoses, fanbelts,gaskets,linings,damaged wooden scrap,waste scrap items,sweeping dust etc.,, ts006-rad.cooler-30,turbo charger-60,a/c head-80, rivet gun-10, master cylinder-22, valve (system production-5, relay-80, abs-24, revaller-4, unloader-3) fanclutch-25, handbrake switch-40, a/c.blower-14, valve door-15, ts007-cond.iron-gi sheet cutting pieces,used empty paint tins and damaged barrels etc.,, ts009-cond.all types of (rexins,seat cushions, rubbers,filter, plastic parts, hoses, fan belts, gaskets,linings, damaged plywoods,sweeping dust etc., etc,, ts012-cond.empty add blue barrels, ts014-cond.temporary driver cabin removed from new chassis, ts021-cond.iron gear wheel main & counter shaft, ts028-cond.iron all types of empty barrels

Central Government/Public Sector

CTN :45329483

17 Jun, 2026 12.61 Lacs

Nagrota - Himachal Pradesh

Tender For provision of 01 x 30 kva genr with connected items as standby power requirements for sewage treatment plant under age (i) bhalra - supply, installing, commissioning and testing, water cooled, sound proof silent type, turbo charged, diesel engine driven generating set 30 kva (at 0.8 pf), 415v, 3 phase, 4 wire engine as per is: 10001/10002 and alterator as per is: 13364, complete with relay panel for automatic starting on mains failure, control panels having meters in an integral acoustic enclosure as per recommendation cpcb norms, comprising of the following:notes: quoted rates shall deemed to include the following also:-(i) supply of t and p and normal space ie., bi-hexagonal ring spanner set of 12 pieces - 01 set.(ii) fuel measuement gauge - 01 no, hand operated fuel lifting pump with steel pipe 40mm dia - 01 no, hydro meter - 01 no, set of fan belt, oil/ fuel filters initial filling of coolant (coolant-2liters).(iii) service maintenance manual along with cat part list and price list - 03 set each.(iv) make of engine and alternator will be got approved from age (i) bhalra before placing the order., (a) diesel engine. diesel engine developing suitable bhp, 1500 rpm inclusive of the following standard accessories:(i) radiator/ heat exchanger cooling system. (xiv) battery charging generator.(ii) spider coupling guard. (xv) industrial silencer.(iii) fly wheel. (xvi) lubricant oil cooler.(iv) fly wheel housing complete with starter gear ring and coupling. (xvii) flexible pipe for silencer. (v) fuel pipes. (xviii) battery volt meter.(vi) air cleaner. (xix) water temperature gauge, lub oil pressure (vii) fuel and lubricant oil filter. gauge.(viii) by pass filter. (xx) speedo meter and engine running hours meter.(ix) coolant inhibitor. (xxi) display for fault.(x) fuel pump. (xxii) turbo charger.(xi) water pump. (xii) lubricant oil pump.(xiii) self/electric starter.(b) alternator : synchronous alternator 3 phase 4 wire, 50 cycles 1500 rpm, self excited, self regulated, brushless type, 0.8 pf, 415v, ac supply, 30 kva capacity, copper wound, complete including necessary tools, mounted on strong rigid steel fabricated base frame and directly coupled through flexible coupling with diesel engine, complete all as specified and directed., (c) amf/ control panel : amf panel factory made of suitable capacity as per original equipment manufacturer make and specification or as approved by oem for dg set of capacity 30 kva of suitable size, indoor cubical type, front and back openable fabricated out of mild steel sheet 1.6mm thick grounted in floor with adequate pcc foundation and minimum consisting of following :(i) contactor of suitable size for 30 kva dg set.(ii) copper bus bar of suitable current rating and sensitivity relay set unit with auxiliary cts.(iii) electronic latch circuit with tripping indication.(iv) re-set facilities.(v) 3 phase mvr relay unit with single phase protection complete with 2 no nc auxiliary contacts.(vi) 3 phase avr relay unit complete.(vii) self sequential starting relay unit 12 volts dc complete with alarm and power contactor. (viii) electronic timer 220 volts for main contactor with 1 no nc auxiliary contactor.(ix) electronic timer 220 volts for fuel cut off operation with 1 no auxiliary contactor.(x) battery charging 2x12 volts 10 amp complete with digital voltmeter and amps meter, including trickle and boost charging, make : su-kam, amco, exide or any other make as recommended by the manufacturer.(xi) volt meter 0-500 volts panel mounting of size 96mm square with selector switch digital type.(xii) amps meter 0-100 amps with 3 nos cts, 400/5 and selector switch 96 mm square digital type.(xiii) frequency meter (45-55) hz, 415 volt, 96mm square digital type.(xiv) the amf panel should have manual by pass arrangement too in case of failure of amf panel., (d) fuel tank of capacity as per manufacturer recommendations.(e) base frame made out of suitable channel duly reinforced and provided with adequate numbers of anti

CTN :45344997

16 Jun, 2026 NA

Multi City - Multi State

Tender For dismantling of rooftop polycarbonate sheets ,turbo ventillators, rain water drain system

corporations/Associations/Others

CTN :45299281

29 May, 2026 27.58 Lacs

Nellore - Andhra Pradesh

Tender For supply & delivery of 3 dx plus 2wd-powered by 430,stage 5 engine, 4cylinder, water cooled, turbo charged with egr and after treatment system doc and dpf loader with 1.1cum & excavator bucket 0.26 cum.diesel engine of 55kw(74hpl @2200rpm,max torque 440 nm@1150rpm and displacement of 3.0l, hydraulic pump flow 114 ipm at 2000 rpm and system pressure is 3915 p.s.i

CTN :45072524

28 May, 2026 NA

Dimapur - Nagaland

Tender For bid to ras corrigendum : supply of prosthodontics lab materials e e - addition polysilicon putty light body three hundred to four hundred gm , firing tray ten zirconia alumina firing pins , metal firing pins , firing wool , glaze paste syringe of three gm for pfm , mockup wax shade ivory , ceramic separating disc diamond smooth of thickness zero point twenty five size twenty twomm pkt of ten , ceramic separating disc diamond smooth of zero point five mm pkt of ten , ceramic separating disc serrated of pkt of ten , daimond impregnated rubber wheel for ceramic polishing pkt of ten , ceramic technique system kit , carbon free wax marginal for all ceramic casting eighty gm , carbon free wax body for all ceramic casting eighty gm , investment powder for all ceramic press vest pkt of hundred gm , investment liquid ceramic press vest bott of thoushand ml , silicon casting investment ring with base former two hundred gm , silicon casting investment ring with base former hundred gm , alox plunger for all ceramic pkt of two , alox plunger separator bott of two hundred ml , emax ceram dentin powder shade a one bott of twenty gm , emax ceram deep dentin powder shade a two bott of twenty gm , emax ceram dentin powder shade a two bott of twenty gm , emax ceram dentin powder shade b one bott of twenty gm , emax ceram dentin powder shade c one bott of twenty gm , emax ceram dentin powder shade c two bott of twenty gm , emax ceram dentin powder shade c three bott of twenty gm , emax ceramic transperant enamel powder bott of twenty gm , emax ceram gingival bott of twenty gm , emax ceram impulse powder bott of twenty gm , emax modelling liquid bott of two hundred ml , emax ceramic glaze and stain liquid bott of fifteen ml , emax ceramic glaze powder bott of fifteen gm , emax ceramic essence of various shades set of six bott of one gm each sunset capuccino , diagen turbo grinder kit for all ceramic set of five burs , glaze paste syringe of three gram for pfm ceramic , hf etchant for all ceramic ivoclar , lithium disilicate pressable ingots ivoclar ips e max shade c three , lithium disilicate pressable ingots ivoclar ips e max shade b two , lithium disilicate pressable ingots ivoclar ips e max shade c two , gray elastic modules pack of thoushand

Co-operative

CTN :45282218

28 May, 2026 NA

Kawardha - Chhattisgarh

Tender For supply of re tender engineering items (only oem & authorized dealers) - c.i. welding electrode machinable size 3.15mm, make - ador /essen//d&h secheron/arf/ewac , c.i.welding electrode machinable size 4mm, make - ador /essen//d&h secheron/arf/ewac , c.i.welding electrode non machinable size 4mm, make - ador/essen//d&h secheron/arf/ewac , c.s welding electrode essen 9018 lh size-3.15 mm make- essen/ador/d&h secheron/arf/ewac , forged steel essen dur350 kb/400 kb size-3.15 mm make- ador/essen//d&h secheron/arf/ewac , brass/bronze essen b26 welding electrode size - 4mm, make - ador/essen/d&h secheron/arf/ewac , azukar 80 (brazil) size-4mm, make- essen - welding alloys (sugar mill cane crusher roller arcing electrode , welding electrode 680 cgs size- 4mm, make - l&t/ador/ d&h secheron/ewac , hard facing electrode essen 100, size 2.15mm , make - essen welding /ewac , hard facing electrode essen 100, size 3.15mm make-essenwelding alloys, make - essen,ador /d&h secheron/ewac , hard facing electrode essen 100 size 4mm make - ewac/ador welding/d&h secheron/essen weldin alloy/ewac , hard facing electrode lotherme 605 size 4mm make - l&t/ador welding/d&h secheron/essen weldin alloy/ewac , electrode lotherme 601 size 4mm make - l&t/ador welding/d&h secheron/essen weldin alloy/ewac , m.s. welding electrode e-6013 (king bond), is - 814, er- 4221,size - 2.5mm, make - ador /esab//arf/manglam/atlas/ewac , m.s. welding electrode e-6013 (king bond), is - 814, er- 4221,size - 3.15mm, make - ador welding/esab//arf/mangalam/atlas/ewac , m.s. welding electrode e-6013 (king bond), is - 814, er- 4221,size - 4mm, make - ador welding/ewac/esab/arf/manglam/atlas/ewac , s.s. welding electrode (s.s 308) size - 2.5mm, make - ador welding/esab/essen/arf/atlas/ewac , s.s. welding electrode(s.s308) size - 3.15mm, make - ador welding/ewac/esab/essen/arf/atlas , s.s. welding electrode(s.s 308) size - 4mm, make - ewac/esab/sanweld/essen/arf/atlas , s.s. welding electrode(s.s 309) size - 3.15mm, make - ewac/esab/sanweld/essen/arf/atlas , s.s. welding electrode(s.s 309) size - 4mm, make - ewac/esab/sanweld/essen/arf/atlas/ewac , electrode 7018 size 2.15mm, make - ador welding/ arf/ewac/esab/diffusionewac , electrode 7018 size 3.15mm, make - ador welding/ arf/ewac/esab/diffusion/ewac , electrode 7018 size 4mm, make - ador welding/ arf/ewac/esab/diffusion/ewac , welding electrode superbond s size- 2.5mm, make - ador welding , welding electrode superbond s size -3.15mm, make - ador welding , welding electrode superbond s s size- 2.5mm, make - ador welding , welding electrode superbond s s size-3.15mm, make - ador welding , servo system hydraulic 68, make - indian oil/hpcl/bpcl , servo system 46, make - indian oil/ hpcl/bpcl , turbo prime 46 make - indian oil/ bpcl/hpcl/bpcl , turbo prime 68 make - indian oil/ bpcl/hpcl/bpcl , servo mesh sp - 320make - indian oil/ bpcl/hpcl/bpcl , servo mesh sp - 460 make - indian oil/ bpcl/hpcl/bpcl , servo prime 20w40 make - indian oil/ bpcl/hpcl/bpcl , servo coat 120 make - indian oil/ bpcl/hpcl/bpcl , high temp. servo grease operating htxx is: (nlgi 2) 12790-1999 reaffirmed 2004 make - indian oil , servo elmo pg 2 make-iocl , role guard grease ptfe rainforced grease 1kg. packing , grease for mill central bearing lubrication viscosicty - 1000 capacity 180kg., make - kluber/bechem , multi-purpose lithium base grease ep-3make - indian oil/ bpcl/hpcl/castrol , wheel bearinh grease make- balmerol , transformer oil make - indian oil/ bpcl/hpcl/bpcl , globe valve, screw end 1/2", body tested 10kg /cm²g seat tested 6kg./cm²g, moc - body c.i., sheet - s.s. 304 make - kirlosker/calson/leader/ksb , globe valve ,screw end size-3/4", body tested 10kg /cm²g seat tested 6kg./cm²g, moc - body c.i., sheet - s.s. 304 make - kirlosker/calson/leader/ksb , globe valve, screw end size- 1", body tested 10kg /cm²g seat tested 6kg./cm²g, moc - body c.i., sheet - s.s. 304 make - kirlosker/calson/le

State Government

CTN :44764016

04 Apr, 2026 7.60 Lacs

Hyderabad - Telangana

Tender For corrigendum : tggenco- ktpp-c and i-i- service charges for testing and calibration of turbo supervisory system (tsi) of main turbine and bfps during the capital overhauling of the unit(500mw)

State Government

CTN :45204367

28 May, 2026 NA

Koradi - Maharashtra

Tender For procurement of turbo hub 800 mm shell diameter non-drive pulleys with shrink disk assembly for conveyor system in chp, 3x660 mw, ktps, koradi.

Central Government/Public Sector

CTN :45195588

04 Jun, 2026 NA

Tiruvallur - Tamil Nadu

Tender For supply of thermal evaporation system with turbo

Spark Plasma Sintering Equipment Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors