Latest sprocket Tenders | Government sprocket Tenders

Central Government/Public Sector

CTN :45332647

16 Jun, 2026 NA

Jaisalmer - Rajasthan

Tender For supply of cylinder liner , piston pin end lock , main bearing set , big end bearing , thrust washer , front tiiming cover seal , rear crank shaft oil seal , cam shaft bush , water pump assy , major over hauling gasket with head gasket , fly wheel ring , fly wheel bush , clutch palte , pressure palte , release bering , oil pressuer switch , temparture sending unit , theromastat valve , cam tikki , inlet end exhaust valve seal set , inlet end exhaust valve seat , inlet exhaust valve guide set , fuel line flexi bale pipe with clamp , inlet end exhaust valve , diesel high pressuer line , rear brake shoe set , master cylinder , 13 no bolt , dieselfilter , m oil filter , air filter , 13 no. stud with nut , banjo washer , anna bond tube , old colth , self starter motor brush holder , self starter bush bearing , self starter carbon bush

State Government

CTN :45179379

01 Jun, 2026 NA

Manaparai - Tamil Nadu

Tender For corrigendum : chipper infeed chain conveyor sprocket works at tnpl unit - ii trichy

State Government

CTN :45118897

29 May, 2026 NA

Srinagar - Jammu And Kashmir

Tender For corrigendum : supply of tinter am073 axalta , tinter am074 axalta , tinter am735 axalta , tinteram732 axalta , tinter am082 axalta , tinteram 7 axalta , tinter am1 axalta , tinter am032 axalta , binder ab150 axalta , binder ab160 axalta , binder ab385 axalta , binder ak350 axalta , binder ak100 axalta , clear 679s axalta , hardener 256s axalta , microfiber cloth , master wipe , palstic primer 810r , masking tape , dust mask , sandpaper 220 no , sanpaper 400 no , leather shine , sandpaper 80no disk type , sandpaper 180 no disk type , body filler , emery paper 80 no , emery paper 180 no , nc putty , ps grey , duco thinner , dull black , duco white , masking paper 24 inch , masking paper 18 inch , duco rubbing compond , writing brush , duco red , painting gun , malmal cloth , surfacer 1k primer , paint spray mask , sander , cleaning brush set , tack cloth , duco silver , dothi cloth , rtv tube jain tube , tail lamp bulb , tail lamp bulb double point 1016 , head lamp tube bulb 90 100 suitable for bolero , head lamp tube bulb 90 100 suitable for sx4 , head lump bulb suitable for ciaz , head lump bulb suitable for scorpio , head lump bulb suitable for safari , head lamp bulb honda city , brake lamp press type t5 , brake lamp press type t20 , brake lamp press type t21 , head lamp holder , car perfume , dash board polish , tyre polish 250 ml minimum , sulfuric acid concentrated , black seal for tubeless tyre , tubeless tyre valve , car body polish 200 ml , carbon cleaner spray 100 ml minimum , hand gloves comfort grip glove for workshop use , portable grinder blade smooth 4 inch , portable grinder blade rough 6 inch , grinder wheel 8 inch smooth , grinder wheel 8 inch rough , windshield cutting wire , foot mat universal rubber 4 piece , fuse micro 10 amp , fuse micro 15 amp , fuse micro 20 amp , insulation tape , electric welding rods , brass welding rods , elfy tube 2 gram , epoxy adhesive fevitite 180 ml kit , elgi gear oil gun 5 litre , velvet cloth golden colour , velvet cloth blue colour , towel cloth white , towel cloth grey , u foam 2 inch sheet , thread reel assorted colors , metal screw one half inch , metal screw 1 inch , metal screw 2 inch , calcium carbide , hydrometer , car washing shampoo concentrated , bastic tin pack of 250 gram //bid details 2 / 73

Corporations And Associations And Others

CTN :45328794

02 Jun, 2026 19.95 Lacs

Delhi - Delhi

Tender For providing t and p items and garden tools for ward no. 171 (cr park) south zone - providing t & p items and garden tools for ward no. 171 (cr park) south zone., supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigssaw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16"pole type: light weight telescopic tubular aluminum alloy extendable poleno of positions for pole heightadjustment: 10 positionslocking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cuttingcapacity: 200mm max, petrol operated brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cuttingattachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight(dry, without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only.multi function handle: should have acceleration, on/off switch at right handle.brushcutter harness: should be double shoulder harness only.anti vibration system: must have 4- point aniti vibration system.vibration level in m/s2 at right handle: should not be more than 2.5 m/s2sound pressure level db(a): should not be more than 105 db(a)drive shaft design: must have drive shaft ends square design type only.certification: must have valid en certification, telescopic petrol operatedpole prunerengine: single cylinder, 2 stroke, air cooled onlydisplacement: should be between 25-30 ccpower output: should be minimum 1.2 hpweight (dry without cutting attachment & fuel): should not be more than 7.5 kgfuel tank capacity (ml): should be minimum 400mlchain oil capacity (ml): must have minimum 200 ml.clutch: clutch shoe linining should be metal only.guide bar length: minimum 30cmguide bar and chain: should have same manufacture onlychain type: every drive link need groove & small oil holes for better lubrication. saw chain pitch should be 1/4" or 3/8picco only and drive link thickness must have 1.1 mm or 1,3 mm.max. output shaft speed (rpm): should be minimum 8000 rpm at chain sprocket.equipment total length with guide bar and chain (cm): should be minimum 220 cm - compressed & total length of equipment -minimum 350 cm - extended.sound pressure level (db/a): should not be more than 95 db(a)vibration measurement m/s2 at control handle extended position: should not be more than 5.5 m/s2certification: must have tuv certification with test standard en iso 11680, supply of lawn mower:-specification:- type of machine walk behind lawn mowers power sourcepetrol engine engine displacement 224ccstart type recoil / pull startspeed control variable speeddrive type all wheel driveblade style rotary typeblade engagement electromagneticcut width (mm) 525 to 549minimum cut height 20 millimetermaximum cut height 80 millimeterblades hardened steelnumber of blades 1number of positions for cut height adjustment 6number of levers for cut heightadjustment: single levernumber of wheels 4front wheel size 203 millimeterrear wheel size 250 millimeterwheel tyres pneumaticif yes, grass catcher / collector / bag volume 70 liter"engine power rating (watt)" 4000 to 4999engine fuel tank capacity 1.4 ltr., supply of synthetic enamel paint in all shades as per required and direction of officer-in-charge., petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be more than 5.0 kgc

Central Government And Public Sector

CTN :45335997

10 Jun, 2026 NA

Bangalore - Karnataka

Tender For supply of 1-1/2" pitch x 16 teeth duplex sprocket as per w.a.p. drawing no. wh-213-1205-3a.alt a ]

CTN :45224103

29 May, 2026 NA

Kamrup - Assam

Tender For corrigendum : supply of spring assy front , chain and sprocket kit , pump housing , cam plate , silencer assy , shoe brake , suspension kit

CTN :45224132

29 May, 2026 NA

Kamrup - Assam

Tender For corrigendum : supply of glass wind shield , rear hub sprocket 38 teeth , pump element , s a of pipe , air pressure pipe , brg inner frt wheel

CTN :45332951

05 Jun, 2026 NA

Kangra - Himachal Pradesh

Tender For supply of eng mtg pad front , cyl head gasket , pressure plate , wiper blade , front wheel brg , clutch master cyl , stg gear box , rear wheel brg , knuckle brg , hub seal 13 no , realy 4 pin 24v , fuel cut off solenoid , relay 24v , clutch master cylinder , clutch sleeve cyl , flasher unit , clutch booster , suspension bush kit , clutch cable , clutch sleeve cyl assy , gear lever kit , air filter , brake shoe

CTN :45347012

06 Jun, 2026 54.0 Thousand

Gwalior - Madhya Pradesh

Tender For supply of water pump , dual brake valve , injector assy fuel , assy water pump , silencer assy , chain sprocket kit , regulator vehicle window rh , assy ac compressure , sleeve kick starter

CTN :45223907

30 May, 2026 NA

Jammu - Jammu And Kashmir

Tender For corrigendum : supply of clutch master cyl assy , set of brake lining , hose air cleaner to turbo charger , water pump assy , saloon out side mirror , wiper blade , wiper arm pentogroph , wiper blade assy 508 mm , wheel bolt m 22 x 15 , oil seal rear hub , dikki assy , cartridge lub oil filter , belt v ribbed 1422 , rubber hose , tempe transducer , height marker lamp red , hold relay , battery cut off switch , side window glass , assy clutch master cyl

Sprocket Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

State Government

Corporations And Associations And Others

Central Government And Public Sector