Tender For installation of gantry rail for 5-ton eot crane at new satellite depot/ nagpur/secr & extension of gantry track for 10-ton eot crane by 20 meters with gantry girder binding at zmd/nagpur/secr.
Tender For execution of p.way works: - 1) complete track renewal (primary) of existing 60 kg 90 uts rail on 60kg psc-14 sleeper with new 60 kg 90 uts rails on 60kg wide based sleepers for a length of 4.539 tkm. between dvd-kuk section (in patches) under aden/track/wat on main line. 2)through sleeper renewal (primary) of existing psc 60 kg sleepers with new wide based 60 kg sleepers along with deep screening and raising of ballast cushion for a length of 2.590 tkm between slo-gpt (in patches) under aden/track/wat. 3) through rail renewal (primary) with 60kg rails for a length of 1.300 km (in patches) from km.759.682 to 760.982 dn line between gopalapatnam -duvvada sections under aden/track/wat.
Tender For execution of p.way works 1) complete track renewal (primary) of existing 60 kg 90 uts rail on 60kg psc-14 sleeper with new 60 kg 90 uts rails on 60kg wide based sleepers for a length of 0.773 tkm from km.1.217 to km.1.99 uni line between vskp-ncc under aden/myd/wat,2) through sleeper renewal (primary) of existing psc 60 kg sleepers with new wide based 60 kg sleepers along with deep screening and raising of ballast cushion for a length of 2.837 tkm scmn-gpt (by-pass) from km.0 to 1.322- dn line & km.1.217 to km.1.99 uni line between vskp-ncc under aden/track/wat.3) through turnout renewal ttr(cs+cmsc)-10 sets under aden/myd on wmy line.4) through turnout renewal -25 sets - ttr(cs)-11 sets & ttr(cmsc)-14 sets in various sections of waltair division 5) through turnout renewal ttr(tfr)-39 sets (1 in 12-6 sets and 1 in 8% 33 sets) under sr.den/south/wat.
Tender For supply of equipotential bonds for siemens make audio frequency track circuit of size 21.5 meter suitable for track circuit ftgs 46 /917. terminal bond should be made of pvc coated wire rope of crosssection approximately to 240 sq. mm. pvc coated wire should be as per is:2266 of 1978 or latest and pvc sheathing should be of compound type 6 as per is:5831 of 1970 with latest amendment if any. reclaimed or recycled material shall not be used. brass lug should be brazed at both ends of equipotential bond and brass terminal in centre of equi- potential bond as per sample and drawing. equipotential bonds are to be fixed along the foot of rail and both ends of brass lug are to be riveted or fixed with nut bolts with web of rail by copper rivets or nut -bolts after drilling holes. note- sample approval from consignee before bulk supply. [ warranty period: 30 months after the date of delivery ]
Tender For tender for supply of fabrication - hex nut m39 3 as per drg 46130002460 s00 r00 with matl as per spec aa10208 rev 07 , thrust brg clamp upper as per drg. 36187000943/02 with matl as per specn. aa10119/15 , drive adjustment block (without item no. 2 of drg) as per drg. 36188090123/00 (var-01) with matl as per specn. aa10119/15 , drive adjustment block (without item no. 2 of drg) as per drg. 36188090123/00 (var-02) with matl as per specn. aa10119/15 , lower support plate (bm-009.63) as per drg. 36187000950/01 with material as per specn. aa10122/15 , skate roller and frame assly as per drg. 26187001159/03 with material as per drawing , coupling guard as per drg 26187001133 01 with matl as per specn is 1079 , hex screw m39 3 140 var 02 hy 705 22 fully m cd item as per drg 46118000943 01 with matl as per specn aa10208 07 , lock nut hex m48x3 as per drg. 46187090156/00 with matl as per specn. aa10208/07 , stud m39x3 1200l as per drg. 36187000949/01 with matl. as per specn. aa10305/08 , jr. stop bolt hy 257 02 fully m/cd item as per drg 36137000839 03 with matl as per specn hy-10664 06 or en 19 u , pin as per drg. 46188000948/01 with matl as per specn. hy10561/04 , output shaft stud as per drg 36187000945 03 with material as per specn hy10664 06 or en 19 u , hex nut m39 3 as per drg bm std 032 rev 00 with material as per specn hy10664 06 or en 19 u , scrapper pin (hy-251.03) as per drg. 36117000898/06 with matl as per specn. hy10664/06 , thrust brg clamp lower as per drg. 36187000942/02 with matl as per specn. aa10119/15 , upper support plate as per drg. 36187000948/01 with material as per specn. aa10122/15 , output shaft skirt assly (hy-705.26)fully m/cd item as per drg. 36118003145/00 with matl as per drg. , tie up of track plate as per drg 46118000883 rev 01 with material as per spec aa10119/15 , skate retainer plate as per drg 46118000887 rev 01 with material as per spec aa10119/15 , locknut wrench as per drg 36187000928 rev 00 with material as per spec aa10119/15 , puller spacer pillow block as per drg 36187000947 rev 00 with material as per drg , mounting block lh as per drg 46188000986 rev 00 with material as per spec aa10119/15 , puller angle plate pillow block as per drg 46188000987 rev 00 with material as per spec aa10119/15 , wrench trunnion shaft end caps as per drg 36188000998 rev 01 with material as per spec aa10119 , mounting bracket-rh as per drg 36188001000 rev 00 with material as per spec aa10119/15 , mounting bracket - lh as per drg 36188001002 rev 00 with material as per spec aa10119/15 , mouting block-rh as per drg 46188001010 rev 00 with material as per spec aa10119/15 , tilt out plate as per drg 46188001013 rev 00 with material as per spec aa10119/15 , spring preload fixture as per drg 26187001185 rev 00 with material as per drg , grinding roll wear meas. gauge as per drg 26188001221 rev 00 with material as per drg , preloading adjusting stud as per drg 36187000929 rev 00 with material as per spec hy10664/06 , high strength stud as per drg 46187000951 rev 00 with material as per spec hy10565/03 , bowl extension ring hoisting clevis (var-01) as per drg. 26188001135/01 with matl as per specn. aa10119/15 , rail connector (rh) as per drg. 46118000885/00 with matl as per specn. aa10108/11 , rail connector (lh) as per drg. 46118000886/00 with matl as per specn. aa10108/10 , channel frame assy as per drg. 16187000532/00 with material aa10119/15 for plates and aa10108/10 for section , bowl hoisting frame hook (var-01) as per drg. 26188001157/00 with matl as per specn. aa10119/15 , rail connector plate as per drg. 46187002214/00 with matl as per specn. aa10119/15 , stud with nut m10 as per drg. 36187000944/01 with matl. as per specn. hy10199 or aa10208/07
Tender For "providing project management services engineering, procurement and construction (epc) contracts and other works contracts ( item rate contracts) for doubling project between agthori station (km 393.380) to kamakhya station (km 401.120) including construction of 2nd rail cum road bridge over river brahmaputra including viaduct, retaining walls, embankment and minor bridges including track work, ohe work, signaling and telecom work and general work in connection with agthori - kamakhya doubling project of northeast frontier railway in the state of assam." and "engineering, procurement and construction (epc) contracts and other works contracts (item rate contracts) for doubling of track between azara (163.000 km) (including) and kamakhya stations (including)up to km 176.000 (13 km) including electrification and signalling works in connectionwith new bongaigaon -goalpara town - kamakhya doubling project of northeast frontier railway."