Latest submersible pump motor set Tenders | Government submersible pump motor set Tenders

State Government

CTN :45734470

06 Jul, 2026 1.53 Lacs

Kolkata - West Bengal

Tender For withdrawing of old pump motor set (no. 2) and reinstallation of new one including some allied works for bore well submersible pump motor set at 19a chetla hut road, kolkata

corporations/Associations/Others

CTN :45734462

10 Jul, 2026 1.21 Lacs

Kolkata - West Bengal

Tender For repairing with replacement of worn out components, burn out winding of 2nos, 10hp capacity submersible pump motor sets at raw water pumping station under grww.

CTN :45724826

06 Jul, 2026 65.3 Thousand

Ranchi - Jharkhand

Tender For repair and renovation (civil and electrical) of 06 nos. d-ii qtrs. at ag doranda ranchi. (sh lifting and lowering of submersible pump motor set change of flat submersible cable and column pipe)

CTN :45724827

06 Jul, 2026 29.3 Thousand

Ranchi - Jharkhand

Tender For maintenance of electrical and mechanical installation in non residential building at pag office doranda ranchi during 2026-27. (sh repairing of submersible pump motor set and other miscellaneous work)

State Government

CTN :45695199

10 Jul, 2026 4.99 Crore

Belgaum - Karnataka

Tender For tender for establishment of centre of excellence in electrical vehicle power train technologies at vtu regional centre, bengaluru - servo motor rotating arm e, propeller fin e, battery connector e, jumper pin header e, battery holder e, usb cable e, button cap (large)passive elements, button(small) passive elements, button(large)passive elements, potentiometer(10ko)passive elements, switchpassive elements, capacitor(10uf)passive elements, capacitor(104)passive elements, resistor(10ko)passive elements, resistor(1ko)passive elements, resistor(220o)passive elements, big blue led active elements e, big yellow led active elements e, big green led active elements e, big red led active elements e, rgb led active elements e, active elements 1n4001 diode, active elements 1n4148 diode, pnp transistor(8550) active elements, npn transistor(8050) active elements e, relay active elements e, active buzzer active elements ev, motor driver e, seven segment display e, lcd display e, dc motor e, servo motor e, jumper wires e, tx/rx module e, tilt sensor e, ultrasonic sensor holder e, light sensor e, ultrasonic proximity sensors e, analog temparature sensors e, breadboards e, uno board e, usb cable for stm32 board e, ecu board, stm32 discovery board e, battery cell making machine, integrated electronics workstation, pcb design equipment, dynamometer 2w, electrical vehicle motors and drives workbench, battery management system (bms) training module e, model-based development (mbd) real-time controller, power electronics training bench, off board charger control board, pe-pp control panels, pdi unit, dc converters, drive axles, wheel axles, foot throttle e, auxiliary battery, relay e, harness, wheels e, differential e, moter ev, bms e, vcu e, mcu e, on board charger, battery pack e, naked chassis, belt pulley e, female type 6 charging socket e, front wheel axle ev, front wheel rim ( 12 inch) e, tubeless tyres e, main stand ev, side stand ev, mid - drive chassis e, switches ignition, horn, indicator, head light ev, cone-set ev, handle bar ev, t-stamp ev, fork ev, smart charger can ev, dc dc converter ev, swing arm ev, vcu ev, brake sensors ev, display ev, wiring harness ev, throttle (re twistable) ev, mid drive motor 3kw and pull belt e, mcu 120a e, battery 4kw nmc ev, cordless drill machine tools ev, tool kit trolley tools e, pipe wrench tools e, screwdriver 803 tools e, taparia screw driver 863 200 tools ev, taparia philips s/d psc862250 tools ev, taparia screw driver 861 100 tools e, installation tape tools ev, soldering gun tools e, multimeter tools e, hammer - 40mm nylon tools ev, hammer - 500g tools ev, chissel tools ev, tools 24pc socket set box, long circlip plier outer tools ev, long circlip plier inner tools ev, t spanner 14mm tools ev, t spanner 12mm tools ev, t spanner 10mm tools e, t spanner 8mm tools ev, t spanner 7mm tools ev, connector - 902 tools ev, tester tools ev, nose plier tools ev, monkey plier tools e, wise grip plier tools e, cutting plier tools e, wire cutter tools e, screw driver 2 in 1 - 903ibt tools ev, ring spanner set tools ev, double end spanner set tools ev, t allen key 3,4,5,6 mm tools ev, l allen key set tools ev, motor hall phase tester ev, continuity tester ev, safety helmet, programmable mcu, clamp meter ev, taco meter ev, mid drive mcu, hub motor mcu, hall sensor ev, mid drive stator, hub drive stator, induction stator, bldc stator, mid drive rotor, hub drive rotor, induction rotor, bldc rotor, induction motor, brush motor, shaft drive motor ev, bldc motor, pmsm motor, ev 4w - car, ev 3w - auto ev, ev2w - shaft drive - full vehicle, ev 2w - hub drive full vehicle ev, ev 2w - mid drive - full vehicle ev, ev 2w - hub drive - full vehicle ev, ev 2w - mid drive - full vehicle, ev 2w - hub drive - full vehicle, eight channel 3 amps cdc cell grading machine, cells bolt, cell 3.2 v 100ah lfp, hot air blower ev, green 100mm insulation, clamp meter 0-600 amps, battery tester, bus bars, screw gauge ev, silicon black, bla

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

Central Government/Public Sector

CTN :45699209

09 Jul, 2026 NA

Dhanbad - Jharkhand

Tender For fabrication and making 23 set 6 inch size pipe clamp and 70sq mm cable hanging clamp and 25mm size u clamp and 2 set rest clamp for submersible pump motor set and lowering of 180 hp, 600 gpm submersible pump motor cable and pipe in 2 pit victory sec

State Government

CTN :45698689

08 Jul, 2026 NA

Parganas - West Bengal

Tender For withdrawing of damaged submersible pump motor set and lowering 7.5hp standby pump motor set at ph-i of sankardaha w/s scheme block_minakhan under eastern mechanical sub division-i, phe dte. dist- 24 pgs(n) (sm/13518)

State Government

CTN :45698692

08 Jul, 2026 NA

Parganas - West Bengal

Tender For withdrawing of damaged submersible pump motor set and lowering 7.5hp standby pump motor set at ph-i of amberia w/s scheme block_minakhan under eastern mechanical sub division-i, phe dte. dist- 24 pgs(n) (sm/13518)

State Government

CTN :45698693

08 Jul, 2026 NA

Parganas - West Bengal

Tender For withdrawing of submersible pump motor set and lowering 15 hp standby pump motor set at ph-iv of sahebkhali w/s scheme block_hingalganj under eastern mechanical sub division-i, phe dte. dist- 24 pgs(n) (sm code-sm/00987)

Submersible Pump Motor Set Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

corporations/Associations/Others

State Government

Central Government/Public Sector

State Government

State Government

State Government