Latest tachogenerator Tenders | Government tachogenerator Tenders

CTN :45048307

31 Jul, 2026 NA

Tarapur - Maharashtra

Tender For corrigendum : : supply, installation, testing & commissioning of electrical equipment for dg block 119a of inrp - ht panels (119a)supply, installation, testing & commissioning of indoor type floor mounted, single front, metal clad, 1250 a, 6.6 kv, 3 phase, 3 wire, vcb switchgear panel suitable for a short circuit current of 31.5 ka for 3 seconds, internally arc tested for 31.5 ka for 1 second, comprising of following incoming & outgoing feeders : incoming feeder: 1 no. 1250 a, 3p vcb outgoing feeders: i) 7 nos. 630 a, 3p vcbii) 1 no. 1250 a, 3p vcb as tie feederwith surge arrestors, relays, pts, cts & other necessary accessories including associated structural steel required for complete installation of the panel & equipment earthing of the panel from both the earthing terminals of the panel to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings. reference drg. nos: ip1/119a/05027339/dwg/001/r0 & ip1/119a/05027339/dwg/002/r0(note: terminal box of each incomer of 6.6kv switchboard shall be suitable for terminating 4x3cx400 sq.mm., 6.35/11kv (e), a2xwy cables.), supply of spares for ht panels as per attached spares list mentiond in section c, part ii of tender, 2.5 mva, 6.6/0.433 kv dry type transformers (119a)supply, installation, testing & commissioning of 6.6/0.433 kv, 2.5 mva, dyn11 dry type cast resin transformer having percentage impedance of 8.5% complete with ht cable end box, lt bus duct flange, off load tap changer on ht side with range of +/-5% in steps of 2.5%, wti scanner, ct for restricted earth fault protection and other necessary accessories including associated structural steel required for complete installation of the transformer & equipment & neutral earthing of the transformer from both the earthing terminals of the transformer to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings.reference drg. no. : ip1/119a/05034347/dwg/001/r0, supply of spares for dry type transformers as per attached spares list mentiond in section c, part ii of tender, 2000 kva diesel generator sets (119a)supply, installation, testing & commissioning of 3 phase 2000 kva prime power 433v, 50hz, 0.8 p.f. diesel-generator sets with 110% overload capacity for 1 hr with four (4) stroke inline or vee type cylinder arrangement having engine speed 1500 rpm, 24v electric battery starting system with a provision of interchangeability of battery bank between two dg sets, complete with all auxiliary equipment including amf control panel, auxiliary mcc panels, heat exchanger cooling system, raw water pump, remote radiator with fans on terrace, ms exhaust piping, exhaust structure (maximum 30 m stack), 4 nos. of 3.6 cubic metre fuel day tank outside dg building (for all 4 dg sets) & 1 no. of 990 ltr intermittent tank inside each dg room, ms "c" class fuel piping between engine & fuel tank, dg room accoustic treatment & complete ventilation of dg room, brushless excitation for alternator, one no. 3200 amp 415 v 4p acb, ms structural steel supports/ channels/ angles & other necessary accessories including associated structural steel required for complete installation of the dg & equipment & neutral earthing of the dg from both the earthing terminals of the dg to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & necessary statutory clearances from cpcb etc. as required and as per tender technical specifications & drawings. design and construction of foundation for exhaust pipe rack/ structure of dg set is included in the scope of the contractor.reference drg. nos. : i) ip1/119a/05034347/dwg/001/r0ii) ip1/119a/05044831/dwg/003/r0iii) ip1/119a/05044831/dwg/004/r0iv) ip1/119a/05044831/dwg/005/r0v) ip1/119a/05044831/dwg/006/r0, supply of sp

CTN :45515815

22 Jun, 2026 NA

Leh Ladakh - Jammu And Kashmir

Tender For supply of spares required for various hydro electric power plants of epd leh - thrust pad (turbine side) for igo mercellong hep as per quantity & specifications mentioned in sbd, thrust pad (generator side) for igo mercellong hep as per quantity & specifications mentioned in sbd, journal pad 300mm for igo mercellong hep as per quantity & specifications mentioned in sbd, lock nut with washers for igo mercellong hep as per quantity & specifications mentioned in sbd, generator gear coupling for igo mercellong hep as per quantity & specifications mentioned in sbd, thrust collor sleeve for igo mercellong hep as per quantity & specifications mentioned in sbd, moog valve assembly for igo-mercellong hep as per quantity & specifications mentioned in sbd, half gland sleeve for igo-mercellong hep per quantity & specifications mentioned in sbd, thrust collor for mhs hunder per quantity & specifications mentioned in sbd, thrust pad for mhs hunder per quantity & specifications mentioned in sbd, journal pad 152.4mm for hunder hep per quantity & specifications mentioned in sbd, journal pad 100mm for hunder hep per quantity & specifications mentioned in sbd, lock nut with washers for mhs hunder as per quantity & specifications mentioned in sbd, thrust collor sleeve for mhs hunder per quantity & specifications mentioned in sbd

Central Government/Public Sector

CTN :45380788

11 Jun, 2026 NA

Tiruchirappalli - Tamil Nadu

Tender For supply of 24 pole tachogenerator for feeder main drive

CTN :45368986

16 Jun, 2026 NA

Erode - Tamil Nadu

Tender For purchase of equipment for electrical machines & power electronics laboratory – eee department - purchase of equipment for electrical machines & power electronics laboratory eee department, on/ off control of lamp using solid state relay kit ssr module: input:3-32 v dc output:24-380v acload: ac lamp.in built dc power supply panel enclosure with necessary input and output terminalspatch cards, dc servo motor driver kit with servo motordc servo motor :12v/24v dc, 5a, 10-60rpm optical encoder or tachogenerator (for speed/position feedback), built-in fixed & variable dc supplies panel enclosure with necessary input and output terminalspatch cards

CTN :45169227

28 May, 2026 NA

Birbhum - West Bengal

Tender For corrigendum : procurement of different consumable items and spares for overhauling of unit 5 and unit 3 under em iph dept bktpp - thinner -234 for varnish, varnish bectol red, varnish bectol grey, silastic 732 rtv (300gm bottle), jointing sheet,asbestos,2000x1500x3 mm # jointing sheet,non-metallic compressed asbestos fibre to withstand 550 degree c,150 ksc is code 2712/9.8 grade w/1,size-2000?1500? 3 mm, jointing sheet caf style 59 oil gasket,, jointing sheet,asbestos,2000x1500x1 mm # jointing sheet non-metallic compressed asbestos fibre to withstand 550 degree c,150 ksc is code 2712/9.8 grade 0/1 size-2000?1500? 1 mm, paint synthetic enamel black, paint synthetic enamel smoke gray, acetone, locktite,406,401, hardner,hy 840 for eco-ash wa drg.no.: hw5520073007, resin,cy 205 $for wound stator assy part no.01350801003122, paint remover,locktite,sf-790 for generator, diluent c,drg:5670269,item no:134 generator, mcb,4 pole,63a,top hat rail mounted # 240/415v ac, o/l relay 415v ac,38.0a - 50.0a reference: lr1-d63357,tc, hose ?" dia.430 mm length # hose ?" dia.430 mm length with fittings grade ph8 design pr.345 bar,insulation resistance 15 megaohms for jacking of 210 mw bhel g enerator shaft, hose 3/8" dia. 430 mm length # with fittings grade ph8,design pr. 276 bar,insulation resistance 15 megaohms# for jacking of 210 mw bhel generator shaft, o/l relay 415v ac mn-2 ss94141 3-5a,l&t, o/l relay 415v ac mn-2 9-15a,l&t cat no. ss94114, contactor,power,coil:240 vac,2no+2nc,32a # siemens auxiliary contact-2no+2nc,coil voltage: 240vac,50hz,type: 3tf34 00-0au0,siemens, mcb,3p+1n,16a,top hat rail mounted # 415v ac,9ka, valve gate gm nb-25mm #, ht rubber tape, gear box assembly complete # paharpur cooling towers model: 10p for stage-ii cooling tower (type-6kf ), switch,hp & lp combine cut-out,kp-15 for ac plant, overload relay,18.0-25.0a,415v ac # type:lr1d-25-322 tc, power contactor lc1d80, relay,electronic,over current,0.5~80a 3dm2-wrduwz schneider operating voltage - 100 to 240vac/dc 50/60hz, aux. contact- ol (1nc+1no), al (1no), over load current setting range - 0.5 a to 80a, mpcb,o/l 56-8oa,s/c 15ka # type:gv3me80 schneider-electric, contactor,415v ac,32a,coil 240v ac for power contactor tc, relay, o/l, 415vac, 0.63-1.0a 3ua-5000-0j siemens, thermal overload relay lrd-32 23-32a lad7b106, mcb,3pole,c100, mcb,80a 415vac 3-pole,c-curve,10ka, varnish elmoluft, strainer,screen oil,compressor js 83 af $for ac plant for compressor model: js 83 af,make-blue star, o/l relay 415v ac lr1d-32-355 28-40a,tc

Central Government/Public Sector

CTN :45246851

22 May, 2026 NA

Nagpur - Maharashtra

Tender For procurement of tachogenerator 24 poles for stg-1 and 2 gravimetric feeders for ntpc mauda

Central Government/Public Sector

CTN :45135793

18 May, 2026 NA

Multi City - Chhattisgarh

Tender For procurement of : tachogenerator,dc,0-4000 rpm

CTN :45121917

01 Jun, 2026 NA

Doiwala - Uttarakhand

Tender For supply of guages and recorder and electronic instruments - h.guru make pressure gauge with s.s.mechanism complete, high accuracy, heavy duty:-, range 0-60 kg/cm dial size 10 fitting bsp( direct), range 0-200 psig, dial 10 fitting ( direct mount) bsp, range, 0-200 psig dial size 6 fitting bsp (direct mount), range 0- -10 kg/cm dial size 4 fitting bsp (direct mount), range, 0-20 psig dial size 6 fitting 3/8 bsp ( direct mount), p.g range 0-150 psi, dial 3 fitting 3/8 dsp direct, range, 0-4 kg. /cm dial size 2 , fitting bsp (panel mount)) centrie, range, 0-2 kg. /cm dial size 2 , fitting 1/8 bsp (panel mount)) centrie, range, 0-2 kg. /cm dial size 2 , fitting bsp (panel mount)) centrie, range, 0-2 kg. /cm dial size 1.1/2 , fitting 1/8 bsp (panel mount)) centrie, range, 0-210 kg. /cm dial size , fitting 2 bsp (panel mount)) centrie, h.guru make vacuum gauge with s.s.mechanism complete, high accuracy, heavy duty:-, range 0-760 mm hg, dial size 10 fitting bsp direct mount, range 0-760 mm hg, dial size 6 fitting 3/8 bsp (male) direct mount, h.guru make temperature gauge with s.s.mechanism complete, high accuracy, heavy duty:-, t.g range 0-150 c, dial size 6 , bulb dia 10 mmtotal immersion length 300 mm(with 2 mtr capillary extra)fitting bsp (m) direct mount, t.g range 0-100 c, dial size 6 , bulb dia 10 mmtotal immersion length 130 mmfitting bsp (m) direct mount, t.g range 0-150 c, dial size 6 , bulb dia 12 mmtotal immersion length 130 mmfitting bsp (m) direct mount, t.g range 0-150 c, dial size 6 , bulb dia 12 mmtotal immersion length 250 mmfitting bsp (m) horizental mount(back side centre), t.g range 0-200 c, dial size 6 , bulb dia 12 mmtotal immersion length 300 mmfitting bsp ( direct mount), t.g range 0-120 c, dial size 6 , bulb dia 12 mm length 300 mm, fitting bsp(m), t.g range 0-150 c, dial size 6 , length 300 mmbulb dia 12 mm, fitting bsp(m) (back side centre), beacon make instruments spares., megnatic pickup model mp-265, line amplefier cum signal conditioner model lasc-5input magnetic pick up, output 2 nos. 5vp to p square pulse, digital techometer indicator, model ldm-5004range 100-19990 rpm, electrical speed indicator model at-6, range- 0-6000 rpmbl 5000 rpm attg 104 rpm, electrical speed indicator model at-6, range- 0-2000 rpmbl 1500 rpm at tg 1500 rpm, electrical speed indicator model at-6, range- 0-8000 rpmbl 6000 rpm attg, tachogenerator, model - tg.fncbl 3vac attg 100 rpm, tachogenerator, model - tg.fncbl 1vac attg 100 rpm, cable same in use in megnatic pickupmp 265, 2.1/2 core copper sheilleded tefflon, multepoint digital tempature indicator model mdi-15, power supply 230 v 50 hz series po/004/05/89, range 0-600 cinput from thermocouple type j , raising power supply (rps) power supply 230v/50hzoutput 24v dc, complete cable type j (iron constant)(conductor standard size), r.t.d. pt-100 complete size 300 mm, thermo couple element type j standard size conductor, 1000 mm, 500 mm, 300 mm, 200 mm, syphon size , air prussure regulator (janatic/shano make)input pressure - 150 psi output pressure 30 psi, digital temprature indicator controllarrange 0-600 c type j (iron constant), digital temprature indicator input fe-k, cr ,alrange 0-600 c - 0-1200 c power supply 230v, 50hz, vacuum gauge tester ravika make (deed wight type), h.guru.south (s.s. machanisum) make, pressure gauge range 0 40 kg/cm , size 4 dial,connection bsp, panel mounting ( back connection), pressure gauge range 0 40 kg/cm , size 4 dial,connection 3/8 bsp, panel mounting ( back connection), pressure gauge - 0 7 kg/cm , size 4 dial,connection 3/8 bsp, panel mounting ( back connection), pressure gauge - range 0 4 kg/cm , size 4 dial,connection bsp, panel mounting ( back connection), pressure gauge - 0 2.5 kg/cm , size 4 dial,connection 3/8 bsp, panel mounting ( back connection), pressure gauge - 0 30 psi/lb/in , size 6 dial,connection 3/8 bsp, direct mounting, range 0 15 psi, size 4 dial, connection 3/8 bsp, direct mounting, steam flow meter with totelizer for boi