Latest target stand Tenders | Government target stand Tenders

Corporations/Associations/Others

CTN :45526721

29 Jun, 2026 1.84 Lacs

Channarayapatna - Karnataka

Tender For annual supply of pipe materials and other spare parts for water supply section of tmc channarayapatna - hand pump- bearing, hand pump bucket bush, two inch pvc cd joint collar, two and half pvc cd joint collar, three inch pvc cd joint collar, four inch pvc cd joint collar, six inch pvc cd joint collar, six inch pvc collar, four inch pvc collar, three inch dp, four inch dp, six inch dp, three by four inch volve packing, oe inch volve packing, one hundred twenty to twentysix inch ring set, thirtysix inch rinch, eighteen inch rinch, fourteen inch rinch, twelve inch rinch, hand pump cylinder, hand pump connecting rod, hand pump bolts and nuts 18 size, hand pump water body, hand pump handles, hand pump- chain, double hand spanner set, cutting player taparia (small), cutting player taparia (big), screw driver taparia 6 inch, screw driver taparia twelve inch, grease gun, hacksaw frame with blade isi, hacksaw blade1, chargeable hand torch, hammer-3 pounds, hammer-five pounds, hose pipe- one and half inch, hose pipe two inch, hose pipe two and half inch, hose pipe three inch, gland packing, three inch air valve, four inch air valve, six inch air valve, sixty hp motor bearing, metal paste1, single phase 1 hp isi mark motor, five by eight into two and half inch bolts & nuts, three by four into two and half inch bolts & nuts, half inch volve packing, three inch pvc elbow isi mark, two into two one by two inch pvc reducer isi mark, two and half into three inch pvc reducer isi mark, three into four inch pvc reducer isi mark, six into four inch pvc reducer isi mark, two inch pvc collar isi mark, two and half inch pvc collar isi mark, three inch pvc collar isi mark, four inch pvc collar isi mark, six inch pvc collar isi mark, solvent cement (gum), transformer oil1, bearing grease1, bunnian waste, m-seal, leather sheet1, five hp ten stage isi mark motor and pump, six hp eight stage isi mark and pump, two point five mm submersible cable, rubber insulation sheet, three inch pvc bend isi mark, four inch pvc bend isi mark, six inch pvc bend isi mark, two inch pvc elbow isi mark, two and half inch pvc elbow isi mark, fourinchpvcelbowisimark, six inch pvc elbow isi mark, two inch pvc tee isi mark, two and half inch pvc tee isi mark, three inch pvc tee isi mark, four inch pvc tee isi mark, six inch pvc tee isi mark, two inch pvc valve isi mark, two and half inch pvc valve isi mark, three inch pvc valve isi mark, four inch pvc valve isi mark, six inch pvc valve isi mark, two inch pvc sbend isi mark, two and half inch pvc s bend isi mark, three inch pvc s bend isi mark, four inch pvc s bend isi mark, six inch pvc s bend isi mark, one and one fourth inch gi pipe b class isi mark, two inch gi pipe b class isi mark, two inch gi bend isi mark, two inch gi elbow isi mark, two inch gi collar isi mark, two inch gm gate valve isi mark, two and half inch gm gate valve isi mark, three inch gm gate valve isi mark, four inch gm gate valve isi mark, two inch pvc bend isi mark, twoandhalfinchpvcbendisimark, two inch pvc pipe isi mark, two and one by two inch pvc pipe isi mark, three inch pvc pipe isi mark, four inch pvc pipe isi mark, six inch pvc pipe isi mark, kal inch pvc pipe isi mark, one and one by four inch pvc pipe isi mark, one and half inch pvc pipe isi mark

Central Government/Public Sector

CTN :45556882

22 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of pneumatic system comprising of main air compressor set (splash lubricated/oil free) along with mounting frame assembled with 3 phase induction motor, filters, and pressure switches, control & air dryer, filters etc., as per clause 4.14.17 of rdso specification. the bidder should indicate the type of compressor offered in this bid.(one set per basic unit) [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45285426

22 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For corrigendum : supply of pneumatic system comprising of main air compressor set (splash lubricated/oil free) along with mounting frame assembled with 3 phase induction motor, filters, and pressure switches, control & air dryer, filters etc., as per clause 4.14.17 of rdso specification. the bidder should indicate the type of compressor offered in this bid.(one set per basic unit) [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45561595

23 Jun, 2026 NA

Multi City - Maharashtra

Tender For auction sale of depot miscellaneous scrap - scrap and unserviceable condemned traction motor stator frame with coil (mp & ip coil) in dismenteled and broken condition with nf attachment with or without insulaton, enamelled coating, ms, plastic, cable lugs etc attachment. (qty approx)

Central Government/Public Sector

CTN :45561600

23 Jun, 2026 NA

Multi City - Maharashtra

Tender For auction sale of depot miscellaneous scrap - scrap and unserviceable condemned traction motor stator frame with coil (mp & ip coil) in dismenteled and broken condition with nf attachment with or without insulaton, enamelled coating, ms, plastic, cable lugs etc attachment. (qty approx)

Central Government/Public Sector

CTN :45555774

22 Jun, 2026 NA

Mumbai - Maharashtra

Tender For supply, termination installation, testing and commissioning of ventilation system on roof of paint shop of lower parel workshop along with complete installation, frame work of suitable size with ms 50mmx 50 mmx 5mm, cabling, cable try work, wiring and protection system with 4 pole 20a mcb for each and mcb board along with 2.5 sqmm cable 4 core and 10 sqmm cable from panel to distribution board for main supply and power full exhaust system of length and height minimum 1 meter with width minimum 400 mm, diameter blades 900 mm, blades rotational speed -620 r/min or more. air flow 30,000 m?/h, noise level shall be less than 70 db, power shall be minimum 750 watt with the flap system and motor starter of 1 hp or as per suitable and confirming to s/iec 60947-4-1 or latest. all electrical works shall be carried out in accordance with the provision of indian electricity act 2003 and indian electricity rules 1956 amended to date and all the safety codes and procedures outlined in the safety codes shall be complied with general and safety requirement shall be governed by is 13947 (pt i) 1993 and is:8623/1993, amended to date. termination of all cables shall be done with bimetallic terminal connector suitable for 2.5 dia aluminium tubular busbar for 20a copper palm copper cu etp cw 0041a and aluminium barrel aluminium al 99.5 cable connector temperature resilience, corrosion resistance size: 2.5 sqmm confirming to is: 5561-1970 with maximum temperature rise of 90 degree celsius. material shall be confirmed to designation a6 of is: 617-1959. breaking resistance for barrel 85 n/m sq m and for palm 225 n/m sq m with stretching a5% for barrel must be for palm 2.5. type test certificate from nabl or any other govt agency lab report shall be attached along with the offer without which offer will be rejected. [ warranty period: 30 months after the date of delivery ] ]

corporations/Associations/Others

CTN :45537838

17 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For disposal of condemned scrap materials - dispoal of condemned scrap materials - june2026, cond scrap plastic paper & cunney bag, cond iron scrap corrosive parts, cond. old damaged beeding & rubber parts, cond scrap cylinder liner & disc brake plate, cond scrap wheel disc, cond scrap 21 plate plastic battery, cond scrap 25 plate plastic battery, cond scrap starter assy, cond scrap clutch viscos with fan, cond scrap turbo charger assy, cond scrap engine aluminium piston with iron connecting rod (as it is), cond scrap engine aluminium piston, cond iron scrap slack adjuster assy, cond iron scrap seat frame, pipes and angle pieces, cond scrap wiper motor assy (as it is), cond scrap electrical parts and wire, cond scrap white filter, cond scrap flap cut pieces, cond scrap tube cut pieces, cond scrap 10.00 x 20 radial tyre -254 nos & 295 x80 -102 (psi), cond scrap 10.00 x 20 radial tyre -109 nos (vnr)

Central Government/Public Sector

CTN :45555987

08 Jul, 2026 NA

Palakkad - Kerala

Tender For high pressure jet cleaning machine working pressure: 200-250 bar water flow rate: 900-1100 liters/hour steam temperature (if applicable): 140-155 degree celsius hot water output temperature: 85-90 degree celsius suction height (from water source): minimum 0.5 m pump specifications critical for durability and pressure stability. pump type: triplex plunger pump pump speed: around 1450 rpm number of pistons: 3 piston material: ceramic minimum feed pressure: 6-8 bar motor & electrical specificationsdefines power and efficiency. power supply: electrical phase: single phase / three phase motor rating: around 7-7.5 kw protection class: ipx5 or higher automatic pressure cut-off: yes heating system (for hot water models) optional but essential for grease removal. burner type: diesel / electric burner power: 60-90 kwfuel tank capacity: around 20 liters detergent tank capacity: around 20 liters hose, gun & lance user interaction components. high-pressure hose length: 8-10 meters electrical cable length: 5 meters spray lance length: approx. 700 mm spray gun: standard high-pressure trigger gun quick-connect couplings: preferred construction & materials ensures robustness and long service life. chassis material: mild steel (industrial grade) body material: mild steel or corrosion-resistant metal wheels: solid rubber wheels frame design: compact, vibration-resistant safety & protection features mandatory for industrial equipment. thermal motor protection pressure relief valve overload protection weather-proof switches low-water cut-off (recommended) dimensions & weight affects portability and storage. weight (without accessories): 140?150 kg mobility: trolley-mounted with heavy-duty wheels accessories (standard supply) high-pressure hose spray gunspray lance nozzle set detergent suction hose operating conditions operating temperature range: 0 degree celsius to 40 degree celsius environment: dusty, humid, industrial conditions [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45358651

19 Jun, 2026 NA

Vellore - Tamil Nadu

Tender For corrigendum : supply of 150 kw 1480 rpm lt motor as per st curve drg no. 4- 00-106-32639 & tech specn teci: ltmotor: rev 05. , 110 kw 1480 rpm lt motor as per ts curve drg no. 4- 00-106-32746 & tech specn teci: ltmotor: rev 05. , 150 kw 1480 rpm, frame size 315l, lt motor as per ts curve 4-00-106-32739 & spcen teci: lt motor: rev5

Central Government / Public Sector

CTN :45555406

30 Jun, 2026 NA

Medchal-T - Telangana

Tender For supply of 0.75 kw (1 hp) 3 phase induction motor, 415v, 1440 rpm, 50hz, ip55 protection, class-f insulation, s1 duty, frame 80, foot mounted and flange type complete with terminal box and cooling fan suitable for industrial application. specification standard values type: 3 phase induction motor power: 0.75 kw/1 hp no 10650 1 10650 voltage: 415v 10% current: 2.1 a speed: 1400rpm frequency: 50hz frame size: 80 protection: ip55 duty: s1 insulation class: f efficiency: 74% mounting: foot mounted ]

Target Stand Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors