Latest tension roller Tenders | Government tension roller Tenders

CTN :45175967

15 Jun, 2026 NA

Chandigarh - Chandigarh

Tender For bid to ras bid to ras supply of piston , circlip piston , piston pin , piston rind std , cylinder linner std , main bearing 010 , big end bearing 010 , cam bush std , sleeve o ring , thrust washer std bm , cr bush std , valve inlet and exhaust , valve guide , valve seat ring intake , valve seat ring exhaust , valve stem seal , oil seal crank shaft front and rear , oil jet with packing , engine gaskit set overhauling complete with gaskit and tappet cover packing , oil filter element , oil pump assy , belt alternator , timing chain assy , clutch disc assy , chain guide set primary and secondary , chain tensioner assy , guide tensioner type assy , oil strainer , thermostate valve , crank sensor , fuel return pipe injector , fly wheel assy , clutch cover assy , bearing clutch release , pilot bearing , fuel filter head assy , fuel filter assy with sep , element primary air , safety element , water pump assy , fuel filter assy , oil pressure switch , temp sensor , egr valve , valve tappet guide , push rod , radiator assy , cooling fan with thermo clutch , vaccume modulator , fip , injector , brake acctuator rear , turbo charger assy , oil return pipe rubber hose , hose pipe set , solenoide switch self 12v , copper brush gear plate self , copper brush set , gun metal bush set , voltage regulater , rail pressure sensor , water in fuel sensor , tensioner roller , engine mounting lh , engine mounting rh , wipper blade , brake dual valve , steering rod with cross , acc pedal , front axle bearing , front axle oil seal , crown wheel front axle , pinion front axle , side view mirror lh rh , concentric slave cylinder , shock absorber assy front , shock absorber rear , rear brake shoe , hand brake cable frt , hand brake cable rear , shocker gas stud hood , propeller shaft 4x4 , fuel injection pump , uj cross , ignition switch , wiper blade front , wiper blade rear , fan belt 4pk 1171 , fan belt 4pk 1115 , wheel cylinder frt rr , suspention bush kit comp front , suspention bush kit comp rear , vaccum moduler , clutch master cylinder , brake master cylinder , fuel filter , ac filter , oil filter , air filter , disc pad front , pipe overflow injector with lock , head gaskit , ball joint upper lower , tail light assy lh rh , reverse light switch , supporting stud intercooler , bleeder clutch slave cylinder , drain plug , vaccume booster , head lamp bulb h7 h1 , self stater assy , self copper brush , self solonoid switch , self bendix pinion , alternator regulator , carbon brush set , wheel stud with nut , hub front comp lh rh 4x4 , wheel bearing front , axle boot kit rubber , water hose plastic with o ring , fog light assy , axle seal front lh rh , fan belt , rear view mirror lh and rh , rear brake shoe set , head light bulb h7 , fuel pump , wiper blade //bid details 2 / 108

State Government

CTN :45456762

13 Jun, 2026 NA

Parli - Maharashtra

Tender For supply of tensioning rollers for 1800mm wide reversible conveyor belts installed at chp ii , 250 mw, tps, parli v

CTN :45281566

08 Jun, 2026 NA

Agra - Uttar Pradesh

Tender For bid to ras supply of tensioning roller , timing belt

CTN :45240268

06 Jun, 2026 1.50 Lacs

Leh - Jammu And Kashmir

Tender For bid to ras supply of automatic matching unit , distributer mechanisam base seal , switch bush button , hoses pipes 8mm , igb seals

State Government

CTN :45402026

23 Jun, 2026 NA

Yamunanagar - Haryana

Tender For supply of coal mill feeder spares - vieweing mirror with whiper (as per sample) , belt tension roller moc: (en-8, forged alloy steel) (as per sample) , seal housing moc: carbon steel 1030 grade (as per sample , head pulley/driving pulley moc: carbon steel (as per sample) , take up pulley with eccentric bearing housing moc: carbon steel , support roller of r/c feeder moc: carbon steel; shaft material en-8 (as per sample) , take up shaft (moc: en8) as per sample ,, bearing housing of connecting plate of head cell of r/c feeder/ moc- aluminium (as per sample) , connecting bushing (with pin) 1 set =10 nos. moc: neoprine rubber with bronz bush (as per sample)

Central Government/Public Sector

CTN :45264914

30 May, 2026 NA

Bhopal - Madhya Pradesh

Tender For supply of 2.2 kw ac crane drive , 5.5 kw ac crane drive , 11.0 kw ac crane drive , 22.0 kw ac crane drive , 37.0 kw ac crane drive , 55.0 kw ac crane drive , 75.0 kw ac crane drive 3 phase, digital ac crane drive 2.2 kw, ac drive should be suitable for heavy duty operation of 2.2 kw. offered ac drive should be suitable for crane-hoist operation. if, separate software required for crane application, it must be clubbed with supply of material. ac input voltage: 380 to 480v ac 10%, 3 phase, 3 wire, 50 hz; mode of control: bi-directional fully controlled 3-phase ac; speed regulation: 1% of base speed; braking: suitable dynamic braking resistance and chopper unit (external or in-built); acceleration time: 0.1 to 1000s or better; deacceleration time: 0.1 to 1000s or better; overload: 150%-1min, 200%-3.0s; ambient temperature: 0 to 50 c (derating shall not occur below 50 c. in the event that derating occurs below 50 c, the supplier shall provide a higher-rated drive to match the requirement); rated current at 50 c: min. current should be 5.5 amps at 50 c; high starting torque at low speed: 200% starting torque at 0.3 hz; two analog inputs: two nos. analog inputs having signal voltages of 0 to 10 vdc or 4 to 20 ma (configurable); two analog outputs: two nos. analog outputs having signal voltages of 0 to +/-10 vdc or 4 to 20 ma (configurable); six digital inputs: pnp/npn; one relay output: with short-circuit and overload protection; two digital outputs: with short- circuit and overload protection; brake release signals: outputs braking signals based on inverter operating conditions to prevent cargo bed rollback and overrunning; load adaptive control: when the actual load level is lower than the configured load level, the system can be operated at a ratio-multiplied speed (in terms of the configured frequency), resulting in significantly better efficiency; load ) /bid number : gem/2026/b/7563714 * /dated: 20-05-2026 & & / bid document 1 / 29 frequency), resulting in significantly better efficiency; load limiter: maintains the safety and rescuability of suspended loads by stopping when excessive torque is detected and by allowing operation only in the direction opposite to that in which the excessive load was detected; cooling capacity degradation alarm: detects and displays cooling capacity drop due to cooling fin clogging caused by dust and cooling fan airflow reduction; igbt life expectancy forecasting: estimates the power cycle life expectancy of the main circuit s igbt semiconductor device temperature due to frequent acceleration and deceleration stoppages, and displays the estimate before the design life is reached; protection: it must have all standard protections like stall protection, instantaneous power failure, single phasing, over voltage, under voltage, over current, inverter overload, thermal overload etc; display console: it must have alpha numeric display console for programming of drive, fault display and operating condition; dynamic qr code: it must have dynamic qr code for trouble shooting; tuning facility: it must have auto tuning facility. this must enable perfect matching of motor coupled to load with regards to optimum acceleration time, deceleration time, speed regulation etc; drive programming software: suitable drive programming software along with necessary connecting cable and adapter for connection with laptop and drive should be provided to get online with the offered drive (laptop not in scope); automatic voltage regulation: it must have automatic voltage regulation function to maintain high starting torque even at reduced voltage; regenerative option: it must be capable of regenerative operation; communication protocol: modbus (rtu/serial) or ethernet (tcp/ip); make of drives: fuji- electric/yasakawa/schneider/abb only; suitable dynamic breaking resistance unit of 60% wattage rating of drive, however the value of resistance is to be decided by manufacturer as per their technical manual for crane-ho

State Government

CTN :45172383

04 Jun, 2026 NA

Parli - Maharashtra

Tender For supply of tensioning rollers for 1800mm wide reversible conveyor belts installed at chp ii , 250 mw, tps, parli v

Central Government/Public Sector

CTN :45024280

19 May, 2026 NA

Tiruchirappalli - Tamil Nadu

Tender For corrigendum : supply of mechanical drawing items for nmco and aw machines d d - pines collet-drg no-3m-12a-25-14428-01 , pines collet retainer ring-drg no-2-m-12a25-05433 , cnc mco main spindle-drg no-3m-12b-16-7889 , cncmco front inner race lock nut-drg no-4m12b1619624-0-0 , cncmco front outer race lock nut-drg no- 3m12b1607887-0-0 , cnc mco front thrust ring-drg no-3m12b1607886 , cnc mco rear thrust ring-drg no-4m 12b- 16-7946 , cnc mco collet lock nut -4m 12b- 16-19256 , cnc mco bearing lock nut-drg no-4m 12b- 16-19794 , cnc mco front drum-drg no-4m 12b- 16-7885 , cnc mco rear drum -drg no-4m 12b- 16-7892 , auto weld tension roller-drg no-4-m-10a65-29980 , auto weld roller-drg no-4-m-10a65-29983 , auto weld feed roller 8 mm-drg no-4-m-10a65-29985 , auto weld wire feed assembly right side- 3m10a3012973-0-0 , auto weld wire feed assembly left side3m10a3012972-0-0 , auto weld knurling roller-drg no-4-m-10a65-30187 , cnc mco inner sleeve 15 deg-drg no-4m 12b- 16-28360 , cnc mco inner sleeve -25 deg-4m 12b- 16-19623 , mco pu roller -3m02f1413653-0-0 , mco v roller -4m02f1428242-0-0

Tension Roller Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

Central Government/Public Sector

State Government

Central Government/Public Sector