Latest ticket machine repair Tenders | Government ticket machine repair Tenders

CTN :45354788

17 Jun, 2026 NA

Shekhapura - Bihar

Tender For bid to ras supply of arduino uno microcontroller , breadboard , jumper wires male female , resistors , led red green , capacitors , transistors , diodes , sensors , lcd , relay module , motors , power supply battery , multimeter , soldering kit , project work station , fpga trainer boards , logic analyzer , dual regulated power supply , arduino uno , stm dev board , pic development kit , raspberry pi , digital multimeter , dac trainer board , rtos trainer , soldering stations , lm analog temp sensor , ds digital temp sensor , ptrtd resistance temp detector , k type thermocouple , ir proximity sensor reflective ir , digital ir obstacle sensor , ir flame sensor , ir temperature sensor mlx90614 , mq two lpg smoke , mq three alcohol , mq six lpg butane , mq seven carbon monoxide , mq air quality , pir motion sensor , ultrasonic sensor , accelerometer , gyroscope , solderless breadboard full size , mini breadboard , jumper wires male male , jumper wires male female , jumper wires female female , ic socket eight pin , ic socket fourteen pin , ic socket sixteen pin , solar cell trainer kit , ujt as relaxation oscillator kit , scr characteristics kit , ldr , photo diode , phototransistor , semiconductor temperature coefficient trainer kit , logic gate trainer kit , ic trainer kit , measurement of steady state and transient response of rl rc and rlc circuits , frequency response of twin t notch filter and to study of active filter , study of single phase inverter trainer , to study the behaviour , determine the transient , to study of pid controller for simullatio n process , to study basic electric al trainer , to study single phase transformer , to obtain efficiency of a dc shunt machine , to obtain efficiency and voltage regulation of a single phase transform , to study dc series motor , make connection of dol starter , test the machines required , maxwells bridge trainer kit ) /bid number : gem/2026/b/7582907 * /dated: 27-05-2026 & & / bid document 1 / 44

CTN :45345533

18 Jun, 2026 10.15 Lacs

Lalpur - Gujarat

Tender For corrigendum : supply of bending machine conduit pipe , bus bar with brackets 1 mtr , cctv camera kit , ceiling fan coil winding machine , conduit pipe cutting and threading machines , control panel , digital multi meter , discrete component trainer , dmx controller 512 , ev charger home 1 phase input , ev charger 3 phase input , file half round 2nd cut 250 mm with handle , file round 2nd cut 150 mm with handle , knife switch dpdt fitted with fuse terminals 16 amp , knife switch tpdt fitted with fuse terminals 16 amp , ladder - tower 3 meters on tyre wheels - min 10ft - max. 30ft , lux meter lcd read out 0.05 to 7000 lumens with battery. , magnetic flux meter , mallet barwood , meter reading instrument mri , potential transformer 415 v, 50hz, pt ratio, 440v.110v,10va , power factor meter digital , primary current injection set , rcc pole with accessories , rechargeable battery 12v,100ah , rubber mat , single phase transformer , single phase variable auto transformer , smart meter 3 phase - smart energy meter , soft starter , solar dc pump 1 hp , solar panel with battery 18 watt , solar street light , solar traffic light , solid state solar base single phase energy meter , spanner d.e. set , tachometer analog type - 10000 rpm , three phase transformer , wheat stone bridge ) /bid number : gem/2026/b/7576252 * /dated: 27-05-2026 & & / bid document 1 / 40

State Government

CTN :45374119

18 Jun, 2026 NA

Thiruvananthapuram - Kerala

Tender For corrigendum : supply of digital trainer kit (q3)

CTN :45276049

20 Jun, 2026 NA

Akola - Maharashtra

Tender For corrigendum : supply of games and sports equipment and uniform for jawahar navodaya vidyalaya akola - games and sports equipment and uniform, hand ball nivia synthetic handball women size 2 handball (standard, pack of 1), hand ball-spartan spirit high tech men handball (standard, pack of 1, multicolor), hand ball-nivia ultima handball (standard, pack of 1), hand bal-nivia trainer handball (standard, pack of 1, stop watch nivia js 307, knee support leader sportz leader sportz knee caps for unisex. whether youre hitting the gym or dealing with knee pain, our premium knee support products offer effective relief and stability (medium), whistle-whistle, 2 packs sports whistles with lanyard & mouth grip, loud crisp sound, black plastic whistles ideal for coaches, referees, and officials, hocky net-franklin sports kids mini street hockey goal - portable folding steel floorball goal - 36" x 24", movable volleyball pole-volleyball poles heavy-duty, adjustable & professional sports equipmentwe are a leading manufacturer and supplier of volleyball poles in india, offering a wide range of indoor and outdoor volleyball post systems designed for schools, colleges, clubs, sports complexes, and professional tournaments. our volleyball poles are built for strength, durability, and precision, ensuring stable net tension and safe gameplay for players of all levels., volleyball net - nivia " knotless volleyball net" with metal wire rope volleyball net (black), volley ball-nivia pu 5000 volleyball size 4 - multicolour, volley ball-nivia kross world vollyball size 4 - multicolour, volley ball-aivin attract volleyball - size: 4 (standard, pack of 1), volleyball antenna-nivia, measuring tape-freemans fibreglass open reel measurement tape (50 m), measuring tape-freemans top line 13mm measuring tape, length: 50 m, ft50, chess clock-chess armory digital chess clock - portable timer with tournament and bonus time features, foot ball-nivia simbolo football size 5 - white orange, cosco cosco premier football size 4 - white black, foot ball net -nivia jh-z003 football net, yonex yonex mavis 350 shuttle cock - green, badminton pole, badminton ne-taxg new goal nylon badminton net - red, yonex yonex zr 100 light badminton racket - black, cosco cosco inova basketball size 7- multicolor, cosco cosco rubber pulse basketball size 7 - multicolor, nivia europa basketball size 7 - orange, jj jonex jj jonex heavy basketball ring with cotton net & screw- multicolour, starting block championship, starting block steel-application typeswimming poolfootplate typefixednumber of footplates1colormulti colorusage/applicationin trackweight1.4 kgbrandhindmaterialsteelfinishingpowder coatedcountry of originmade in indiaavailabilityin stockview in hindi , high jump standard supremeuprights made of special aluminium telescopic pillar construction profiles, which are bolted with 18" square roll away steel base and includes two brackets to place the crossbar, heavy duty construction for maximum stability. comes un-assembled and can be assembled very easily by screwing four screws. height adjustment from 160cm to 270cm., amber athletic gear cast iron shot put weights 1kg - ideal for track & field training - color may vary., amber athletic gear cast iron shot put weights 1.5 kg - ideal for track & field training - color may vary., gymfreak pack of 1 bamboo javelin for practice 8 ft. aluminium tipped javelin for boys, girls, women (240 cm 1000 g), gymfreak pack of 1 bamboo javelin for practice 8 ft. aluminium tipped javelin for girls, (240 cm 1000 g), nelco sp0001610001 wooden discus throw disc (1.75 kg), nelco lo spin competition discus - 0.75 kg to 2.00 kg, stag iconic stag iconic indoor/outdoor economy table tennis net, stag iconic stag iconic super mini table tennis (t.t) table| portable indoor ping pong super mini table for kids fun recreational play| included with tt rackets and balls| all in a briefcase-size foldable design, stag iconic era 150 indoor table te

CTN :45541202

23 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For purchase of tanche - lab equipments for eee and ece department - purchase - lab equipments for eee department electronics lab, single phase to single phase cyclo converter kit single-phase bridge cycloconverter power devices: scr/triac based input supply: 230 v ac, 50 hz step-down isolation transformer 230 v / 12 v output: 12 15 v ac, frequency: 0 25 hz (adjustable),firing angle control circuit and frequency control circuit to be provided built-in resistive load, terminals to be brought on ms panel with necessary symbols and circuits, pwm based step down dc chopper using mosfet/igbt kitpwm based step-down dc chopper (buck converter) power device : power mosfet / igbt based switching circuit input supply : 24 v dc to 110 v dc or derived from 230 v ac mains through rectifier unit output voltage :(0 to vin) variable dc output current : up to 5 a dc maximum with suitable load resistor (r load) pwm duty cycle control provided pwm generation and control circuit inbuilt gate driver circuit provided, single phase single pulse / sinusoidal pwm inverter using mosfet/igbt kittype : single phase pwm inverter trainer power device : mosfet / igbt based inverter circuit input supply : 12 24 v dc output voltage : 30 v rms ac output phase : single phase output frequency : 0 50 hz variable output power : 100 w single pulse pwm operation sinusoidal pwm (spwm) operation variable frequency control pwm generation and firing control circuit inbuilt gate driver circuit provided test points provided for waveform observation and analysis built-in resistive load provision, on / off control of lamp using solid state relay kittype : solid state relay (ssr) trainer kit control/input voltage : 12 v / 24 v dc or up to 30 v dc output load voltage : 230 v ac, single phase load control : on/off control of ac lamp load solid state relay based switching circuit opto-isolated input control built-in ac lamp load manual on/off switching arrangement led indication for input and output status, speed control of ac motor using vfd drive module with ac motortype : variable frequency drive (vfd) module input supply : 415 v ac, three phase, 50 hz output : three phase variable voltage and variable frequency ac output 1 hpthree phase squirrel cage induction motor415 v ac 50 hz &1440 rpm control technique : pwm / spwm based control frequency range : 0 50 hz variable digital display for frequency and operating parameters start / stop and forward / reverse control, acceleration and deceleration control facility powder coated ms control panel tabletop / floor mounted laboratory type setup clearly labelled circuit diagram and control switches proper insulated terminals and earthing arrangement, purchase - lab equipments for eee department electrical machines lab, three phase transformertype: three phase transformer, rating: 3 kva input voltage: 415 v ac, 3-phase, output voltage: 230 v ac, 3-phase frequency: 50 hz winding material: copper wound insulation class: class b or higher duty: continuous duty suitable for laboratory usebench/floor, dc stepper motor drive kit with stepper motorinput supply : 230 v ac, 50 hz stepper motor : permanent magnet / hybrid type with suitable driver circuits. motor operating voltage : 12 24 v dc variable speed control forward and reverse direction control full step and half step operation manual / automatic pulse generation facility built-in regulated dc power supply led indication for phase sequence and status test points provided for waveform observation start / stop control switches to be provided overload and short circuit protection to be provided mounted on compact powder coated cabinet with printed circuit diagram proper insulated terminals and interconnecting leads to be provided patch chords for interconnection., dc servo motor drive kit with servo motorinput supply : 230 v ac, 50 hz servo motor type : dc servo motor with feedback arrangement motor operating voltage : 12 24 v dc controller type : microcontroller based servo drive contr

CTN :45535209

20 Jun, 2026 NA

Coimbatore - Tamil Nadu

Tender For purchase of equipment - equipment, single output regulated dc variable power supply (detailed specification - ref nit), dual output regulated dc variable power supply (detailed specification - ref nit), dso (digital storage oscilloscope) (detailed specification - ref nit), digital ic trainer kit with breadboard (detailed specification - ref nit), decade resistance box (detailed specification - ref nit), lvdt trainer kit (detailed specification - ref nit), fiber optic communication trainer kit (detailed specification - ref nit), microwave test bench with reflex klystron oscillator (detailed specification - ref nit)

CTN :45532259

21 Jun, 2026 NA

Kanchipuram - Tamil Nadu

Tender For supply of mechanical and electrical equipments - supply - mechanical lab equipments, single phase ac circuit kit for voltage, current and power measurement- 5a,300v, 300w/5a measurement of power by using various loads analog voltmeter 0-300v ac panel mountedanalog ammeter 0-5a ac panel mountedanalog wattmeter 1.5kw ac panel mountedsingle phase digital power monitor to measure powersingle phase ac lamp load 230v/5a 1kwpanel enclosure with hylam front panel with input/outputterminal outlets , mcb elcb trainer kit- 1 phase/3 phase, 2/3/4 pole, 3a-16a single pole mcb 2-5ampstwo pole elcb 30malamp load single phase 5amps panel enclosure and terminal outlets, four stroke petrol engine cut section model - single cylinder four stroke petrol engine cut sectional model with carburetor, spark plug, cut cylinder, piston, connecting rod, crank shaft, valve mechanism, cam shaft, timing gears and flywheel. all parts cut opened to study the components and its working provision to take values for valve timing. surface finish: painted and color coded for easy identification of components mounting: heavy-duty ms fabricated stand/base display type: static / dynamic demonstrationmodel, dc motor - type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armaturefeatures: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder - bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply: mounted on training base suitable for dismantling and inspection, bearing with shaft assembly - type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips lock nuts end coversmounting: bench-mounted / frame-mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit- the plummer block housing material: cast iron (grade fg 200 or equivalent).type: sng or snl series (split-type housing).sealing: felt seals or v-ring seals (to demonstrate lubrication retention).lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearingtype: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series).bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: groundcarbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., (a).sliding mesh gear box for dismantling and assembling - (a) max transmitted power 1to1.5hp, torque capacity- 40 to 200nm, number .of speed 3 to 6, gear module 1.5 to 2, sliding mesh gearbox gearbox type- sliding mesh forward gears- 3reverse -yes gear material -alloy steel lubrication- splash / oil gear teeth- spur typical gear ratios- 3.2:1 / 2.0:1 /1.3:1 input speed- 0 1800 rpm housing material- cast iron(b) constant mesh gear box cut section - constant mesh gearbox (cut section) gearbox type :constant mesh forward gears :4 gear teeth -helical / spur dog clutch type- sliding lubrication -oil sae 80w90 housing- cut section material -hardened alloy steeleducational features-labeled parts., measurement scale: a vertical steel meter scale, usually with (1mm) graduations, for precise deflection measurement., accessories: includes a set of slotted weights (e.g., (6times 50g) or similar sets) for incremental loading.

CTN :45386606

22 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For corrigendum : supply of lab equipment for electronics and communication engineering department - consumables, function generator (item code: c003), dso (digital storage oscilloscope) (item code: c004), dc voltmeter (digital) (item code: c006), dc ammeter (item code: c007), single phase induction motor (item code: c015), auto transformer (item code: c016), strain gauge trainer kit (item code: c018), dth trainer kit (item code: c021), sim reader trainer kit (item code: c023)

CTN :45516016

03 Jul, 2026 NA

Salem - Tamil Nadu

Tender For purchase of equipments for digital electronics, microprocessor and microcontroller laboratory(asper specification) - equipments for digital electronics, microprocessor and microcontroller laboratory, 1. digital ic trainer kit-7nos2. ammeter (0-25a) mi type-5 nos3. voltmeter (0-600v) mi type -5 nos4. tachometer digital type -5 nos5. 8051 micro controller trainer kit with power supply- 10 nos6. 8255 interface board-3 nos7. 8251 interface board-3 nos8. 8259 interface board-3 nos9. 8279 keyboard / display interface board-3 nos10. traffic light control system-3 nos

CTN :45504878

24 Jun, 2026 NA

Uthangarai - Tamil Nadu

Tender For supply of lab equipments for ece - dc regulated power supply (dual) (for specification refer nit) digital storage oscilloscope (for specification refer nit) moving coil microphone kit (for specification refer nit) 8051 microcontroller trainer kit (for specification refer nit) single phase induction motor with break drum (for specification auto transformer (for specification refer nit) thermistor kit (for specification refer nit) dth trainer kit (for specification refer nit) television (for specification refer nit) fiber optic demonstration trainer kit (for specification refer nit)

Ticket Machine Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government