Get complete information related to latest Tippler Spares Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Tippler Spares Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Tippler Spares Tenders.
Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging
Tender For repairing eye hole of boom, two arm link and h-link, and fitment of bush in boom, two arm link and h-link of shovel, repairing of cracked portion of boom cylinder eye, arm cylinder eye and two number of side link, repairing of be300 shovel sl no16121
Tender For auction sale of depot ferrous scrap - ms fabricating scrap : actual lot no. 03122605 1029. pl no. 98050047 (15) (hsn code 72044900--gst 18%-on fcm basis) scrap of cond. & unserviceable ms fabricating scrap of location boxes, different sizes. cut pcs of sheets eolb hinges, molb boom pcs, tljbs, pedestal stands, channels after coolers, rolling shutters, pannel boards, power junction boxes, rotary ladder trolley, iron stand, tubs, pallets, assembled boxes earth bonds signal ladders rods, steel racks, revolving chair, operator seats, junction boxes, cut pcs angles channels cls panel, ms clamps, s type chair cut pcs office s type chairs, revolving chairs, conference table, lecturer table, office table, duel desks, monkey climber devices, tool cabinets, wall iron frames single and double ladders, circuit breaker boxes, guard sheets, lockers, pipe pcs., tljbs, mddb boxes, slab rods, side body frames, shutters with flat tube light frames j hooks different sizes of sheets and pipes doors shutters seat frames chairs cupboards ms fencings, tool boxes, operator seats, wheel discs stands, panel boards mvmt ducts signal ladders guard seats cots and other miscellaneous items of wagon, s&t, loco, emu, ttm and electrical full or broken with or without attachments. this material available at lot no. 1038,0938a .location road no.4(gas cutting should be minimum depends on material size and weight, maximum 6 cuts permitted only) (image attached). (note: 1. if any ss/ corten steel & non-ferrous items found during cutting / loading / delivery shall be return to the railways by the purchaser 2. in case of clubbed lots, purchaser has to clear the lots in the sequence as mentioned in the lot description and no deviation is accepted. 3. no picking and choosing of material is permitted while taking delivery
Tender For auction sale of depot ferrous scrap - cond. and scrap m.s and c.i signaling released material comp. of padstal, wench machine, counter weight, wheel, interlocking lever, crank, fish plate, cable marker, nut bolt, bottom/top roller, wire adj. screw, joint, discounting link, point side, gate boom barrier, foundation,terminal,locking topper, extended bracket, main signal unit, cls unit 1 to 4 aspect arm signal, signal post, signal base, girder, lifting barriar lever,lpipe,channel, pole, pole stand angle, ground liver frame, straight arms, all type of lock, crank, and wheel, hand plunger lock, panel indication lock,epd, slideing boom gate, mlb, bell, boom solid joint, winch set, weight, pully vertical and horizontal and other miscellaneous signal items with or without n/f attachment. as is where is basis. as it is. note:- loading by purchaser.
Tender For supply of v belt , nut 3 by 4 inch , side cutter teeth left , side cutter teeth right , center teeth , teeth with nut and bolt , boom cyl oil seal , shims all types , oil cooler pipe , hyd pipe for boom , jack cyl seal for loader , 9cm lth 1 by 2 cm o d pipe , 1.5 cm hose clips , 24 cm lth corr hose , 12cm lth 3 by 16cm o d pipe , ammeter , clamp jublee no 4 , gasket , key , seal oil , o ring , bearing , bolt joint , cap , ring snap
Tender For supply of octagonal boom section-03 as per drg no: rdso/s-11600 duly painted with coupling for third joint with 16 nos. of nuts & bolts with spring washer out of which 8 nos. of nuts to be welded on inner side of smaller section of coupling plates at the hole positions. additional 8 nos. of holes of 12mm dia.to be drilled on spot welded side of coupling plates and boom. party should submit nabl authorized lab certificate along with material. [ warranty period: 30 months after the date of delivery ]
Tender For rebuilding and embodiment of bucket assembly along with replacement of tooth pin and adaptor making rear wheel hub drive replacement and both side boom cylinder seal replacement in cat payloader model 988h mc sl no a7a00281 under ttk ocp rajhara area
Tender For auction sale of depot ferrous scrap - 12112ms26b, 98050011, quantity- 79.435 mts. scrap condemned unserviceable ms-ci signal interlocking materials consisting of levers, rods, ms campus rollers of molb, molb weights, molb booms, signal tubular post, roller trestle, stop boards, 33 mm rods, signal arms, gi and ms wires, lc gate pipes, gate structures, ladders, angles, channels, joists, roller stands, electric poles, cable termination box, direct type lever frame, sa 1914 type trays, sm slides, ssi termination rack, control panels, signal booms, boom locks, cable termination rack, adjustable crank, e type lock, cable marker, ground connection rods, fuse unit, power racks, cam path, gear box, signal reverser, ground lever frame, molb, eolb pedestal, telecom charger body, wire adjustment screws, molb compass roller, gate weights, cls tubular post, surface base, nuts, bolts, rounds, turnout wheels, eye joints, point machine covers, clamps, signal buckets, pulleys, d.w.diversion wheel, gate control panel, calling on unit, gear box assembly with clutch, winch, offset brackets, h.p lock, chequered plates, ptb, location boxes, rkt, axle counter coil fixing plate, shunt signals, route arm, route [1 way, 2 way, 3 way and 4 way], ib hut cut parts, ms electrical point detector, junction type route indicator, route indicators, structures, casing structures, ci bases, gear wheels, flats, cable termination base, u- brackets, ci weights of booms, fabricated posts, cls 2, 3 and 4 aspect units, trestle, sge block instrument, y-crank, stands for wheel tension measuring devices of d.w clutch, lock bar clips, drum clock, ec boxes, relay racks, tlj boxes, foundation shoe, ekt, pd clamps, galaxy stand, meeting posts, signal lamp structures, point rods and other similar signal and interlocking scrap material of sorts and sizes, with or without attachments including negligible nf attachments. note- nf attachments are approximately 2 percent of lot quantity. location- bin no- 112, right side of road no- 1. hsn code- 72044900. gst- 18 percent note: private crane permitted for loading purpose. note- delivery on actual weighment basis only. special note: overload of the carrying capacity of the vehicle will not be permitted at the time of taking delivery as per motor vehicle act 1988.