Latest tongue terminal end Tenders | Government tongue terminal end Tenders

Central Government/Public Sector

CTN :41797202

03 Oct, 2025 2.58 Lacs

Dhanbad - Jharkhand

Tender For tender for supply of enm electricals spares item e e - detector , winding temperature , 0-150 c , 250vac 110vdc , thermometer oil temp msrng assembly , isolating plug board assy with 3 phase is , part no. k420k401k301 , volt meter , part no. 81279317 , amper meter , part no. dgm100

Central Government/Public Sector

CTN :41819486

29 Sep, 2025 NA

Multi City - Multi State

Tender For supply of feeders-1&2 and bus coupler, power contactors, 3pole, 1000v ac, 50hz, suitable for 500 kva, 750v ac onload switching under ac-6a category at temperature of 70 degree c &coil voltage of 110v dc +25%-30% with surge suppressor, 2no+2nc, as per rdso spec no. rdso/pe/spec/d/tl/0195-2019 (rev.-0) suitable for switch board cabinet for hog compliant lslrd coaches. accepted makes & models as per s.no.1 of bom of rdso specification mentioned in the above description : (i) abb af1250, (ii)l&t mvo 820, (iii) 3rt12766nf368ka0 of siemens (vide jdse (tl-ac systemdesign) / rdso lr. no. el/7.1.108/sbc/lslrd dt.08.11.23 attached for this modified model number) only. [ warranty period: 30 months after the date of delivery ]

State Government

CTN :41742615

25 Sep, 2025 NA

Supaul - Bihar

Tender For supply of electrical and electronics engg. lab equipments - symmetrical and unsymmetric al faults of transmission line, testing of hrc fuse and mcb overcurrent trainer, relay, vcb trainen, three phas air circuit breaker (acb) trainer, differential relay trainer transformer kit for, generator protection relay trainer kit, dc servo position control trainer kit, ac servo position control trainer kit, stepper motoer, synchro transmitter receiver , ammeters mi type, voltmeter mi type, wattmeter single phase/three phase , three phase power factor meters , automatic power factor controller, low power factor wattmeter single phase , lux meter, digital/energy meter shunt multiplier, current transformer potential transformer, model of mi mc, dynamomete rand induction type meters, lcr/q meter hand held type, soldering iron synchroscop je frequency, clip-on meter, electrical and electronics tools, three phase, squirrel cage induction motor (cut section model), shp three phase ac slip ring induction motor trainer, dc shunt motor-alternator set, basic wiring tools, solar cell experiment setup, spv stand, main rack, brushless dc motor trainer kit, dual power supply, multimeter, lcr meter, cathode ray oscilloscope, function generator, signal generator, digital ic tester, analog ic tester, smd soldering equipment, cables/connectors, television set, television set, projector, maintenance kit, tools, vacuum cleaner/blower, components, microwave test bench, klystron power supply, microwave test bench-x, vswr meter, frequency meter, pin modulator , dso, dc regulated power supply, synchro transmitter and receiver trainer kit, servo motor, on-off control kit, temperature sensor, pi controller kit,, temperature sensor, pd controller kit, temperature sensor, pid controller kit, temperature sensor, plc, digital multimeter , routers, repeater, hub, switch, connecting cables and connectors, network bridge, null modem.cable , microcontroller trainer kit, cro, stepper motor, 7-segment led display, trainer board, trainer board, trainer board, microcontroller board, sensors, digital multimeter and micro-ammeters a, dual channel cro, passive components, resistor, variable inductor, potentiometer, digital multimeter, true rms multimeter, dual channel cro, dc regulated power supply, scr, dc regulated power supply, thyristor kit, resistive load, resistive- inductive load

CTN :41758586

13 Oct, 2025 NA

Guwahati - Assam

Tender For equipments for smart factory and digital manufacturing lab - laser engraving / cutting machine, 3d printer, digital force gauge, temperature humidity mete, pcb making/printing machine, digital micrometer screw gauge, digital vernier caliper, vibration meter, hot wire cutter, soldering station, smd soldering station, digital tachometer, light meter, electric impact drill kit, hand drill stand, 3d printing filament, wire cutter, labview software (labview academic software avl, subscription license, with media (15 user's) with 3 yr ssp), ni hardware (analog discovery studio max with signal & system board (power cord), ni hardware-analog discovery 3 pro bundle, ni hardware-miodaq (usb- 6421), ni hardware-nexys a7- 100t, pcb milling machine, fdm 3d printer

CTN :41758589

09 Oct, 2025 NA

Guwahati - Assam

Tender For equipment for embedded system lab - laser engraving / cutting machine, 3d printer, digital force gauge, temperature humidity mete, pcb making/printing machine, digital micrometer screw gauge, digital vernier caliper, vibration meter, hot wire cutter, soldering station, smd soldering station, digital tachometer, light meter, electric impact drill kit, hand drill stand, 3d printing filament, wire cutter, labview software (labview academic software avl, subscription license, with media (15 user's) with 3 yr ssp), ni hardware (analog discovery studio max with signal & system board (power cord), ni hardware-analog discovery 3 pro bundle, ni hardware-miodaq (usb- 6421), ni hardware-nexys a7- 100t, pcb milling machine, fdm 3d printer

Central Government And Public Sector

CTN :41764732

19 Sep, 2025 NA

Bongaigaon - Assam

Tender For supply of hog a & b main power contactors, 3 pole, 1000v ac, 50hz, suitable for 500kva, 750 v ac onloadswitching under ac-6a category at temperature of 70 degree c & coil voltage of 415v + 10% -20% ac with surge suppressor, 2 no. + 2nc, as per attached rdso spec no. rdso/pe/spec/d/tl/0195-2019 (rev -0) suitable for switch board cabinet for hog compliant lhb lslrd coaches. make ( as per rdso spec bill of material) - abb (model no. af 1250-30-11), l&t (model no. mvo 820), siemens (model no. 3tf69448 cq7za02) for lhb lslrd coaches in hog panel. make-l&t, siemens, abb only

CTN :41751483

23 Sep, 2025 NA

Gopalganj - Bihar

Tender For supply of electronics engineering d d - galvanometer, resistance , voltmeter, ammeter, multimeter, function generator , rtd, thermistor kit , strain gauge kit , microwave test bench , klystron power supply , microwave test bench x , vswr meter , frequency meter , pin modulator , synchro transmitter and receiver trainer kit , servo motor , on off control kit, temperature sensor , pi controller kit, temperature sensor , pd controller kit, temperature sensor , pid controller kit, temperature sensor , plc , digital multimeter , function generator , dual power supply , rf signal generator , regulated power supply , amplitude modulation demodulation trainer kit , fm trainer kit , trainer kit for fm modulator using ic 566 , trainer kit for fm demodulator using ic 565 , soldering iron kit , bjt , mosfet , routers , repeater , switch , connecting cables and connectors , network bridge , null modem cable , packet tracer , stepper motor , 7segment led display , adc 0808 trainer board , dac 0808 trainer board , lcd trainer board , microcontroller board , temperature sensor , ultrasonic sensor , lightdependent resistor sensor , jumper wire ) /bid number : gem/2025/b/6650635 * /dated: 08-09-2025 & & / bid document 1 / 38

Central Government/Public Sector

CTN :41238483

16 Sep, 2025 NA

Raipur - Chhattisgarh

Tender For corrigendum : rate contract for kirloskar chiller make chiller spares for ntpc groupstations - valve angle,55.400.13.353,kcpl, thermowell assy,55.400.34.103,kcpl, sight glass,55.400.18.025,kcpl, evaporator assy,50.260.41.k11.m0,kcpl, gasket,55.400.46.020,kcpl,kw4 320.24, inlet distributor,55.400.67.157,kcpl, gasket nam,55.400.46.020,kcpl,kw4 320.24, thermowell,55.400.37.101,kcpl,kw4 320.24, gasket,55.400.41.504,kcpl,kw4 320.24, angle valve,55.400.13.303,kcpl, safety valve,55.400.11.503,kcpl, flange,55.400.68.076,kcpl,kw4 320.24, valve,55.400.14.209,kcpl,kw4 320.24, core,55.400.25.061,kcpl,kw4 320.24, safety valve,55.400.11.301,kcpl, adaptor,55.400.67.115,kcpl,kw4 320.24, flare nut,55.802.65.003,kcpl,kw4 320.24, ring seal,15.360.00.604,kcpl,kw4 320.24, lubricating oil,55.400.81.303,kcpl, gasket,55.400.40.052,kcpl,kw4 320.24, shut off valve,55.400.12.390,kirloskar, valve angle,55.400.13.301,kcpl, valve assy,55.400.16.320,kirloskar, o-ring,55.073.45.672,kcpl,kw4 320.24, protection unit,56.125.50.012,kcpl, temperature sensor,56.101.50.046,kcpl, board carel,56.137.50.0148,kirloskar, pressure sensor,56.103.50.13,kcpl, prs sensor cable,56.103.50.014,kcpl, level switch,55.400.16.002,kirloskar, stop push button,56.119.50.039,kcpl, cap sov contact,56.226.50.003,kcpl, voltage proct device,56.126.50.032,kcpl, display,56.137.50.152,kirloskar,chiller, t lan serial card,56.137.50.150,kcpl, oil filter,10.000.25.001,kcpl, safety valve,55.400.11.508,kcpl, safety valve,55.400.11.512,kcpl, flush mounting,56.137.50.318,kcpl, cable,56.104.50.557,kcpl, temperature sensor,56.101.50.047,kcpl, protection unit,56.126.50.012,kcpl, k-smart controller,56.137.50.140,kcpl, lan protocol,56.137.50.161,kcpl, elct expansion valve,55.400.17.e06,kcpl, oil level switch,55.400.16.002,kcpl, k-smart controller,56.137.50.202,kcpl, t lan serial card,56.137.50.150,kcpl, voltage protec unit,56.126.50.064,kcpl, oil filter,10.000.25.001,kirloskar, current transformer,56.127.50.187,kcpl, butterfly valve,55.400.12.114,kcpl, sight glass,55.400.18.012,kcpl, jet pump assy,55.400.23.101,kcpl, thermowell,55.400.34.104,kcpl, water nozzle,55.400.37.103,kcpl, thermowell,wtr nozle,55.400.37.108,kcpl, shut off valve,55.805.12.010,kcpl, gasket-body flange,70.220.20.264, gasket strip,55.400.41.503,kirloskar, shut off valve,55.805.12.009,kirloskar, gasket,55.400.40.402,kirloskar, gasket,55.400.46.316,kirloskar, gasket,10.w37.01.140,kirloskar, control gasket,10.wk3.90.113,kcpl, gasket,10.w39.01.039,kcpl, suction filter kit,10.wk3.90.114,kcpl, capillary tube,10.w39.0a.138,kirloskar, safety relief valve,10.w35.01.104, check valve kit,10.wk3.90.110,kirloskar, supervisory board,pcos004850,kcpl, relay,56.134.50.040,kcpl, board controller,56.137.50.388,kcpl, thermowell,55.400.37.102,kcpl, anabond,55.400.91.207,kcpl, coil&connector kit,10.000.16.cxh.c,kcpl, gasket,55.400.46.052,kcpl,heat exchanger, current transformer,56.127.50.188,kcpl, filter oil,55.400.25.401,kcpl,kwf 250.12, gasket&o-ring kit,11.000.00.988,kcpl, crank case heater,56.700.50.150,kcpl, heater,55.400.58.250,kcpl,kwf 250.12, safety valve,55.400.11.516,kcpl, safety valve,55.400.11.314,kcpl, gasket,55.400.46.315,kcpl,kwf 250.12, lan protocol,56.137.50.161,kirloskar, pressure transducer,56.103.50.013,kcpl, pressure transducer,56.103.50.015,kcpl, valve solenoid,56.100.16.320,kirloskar, voltage proct device,56.126.50.064,kcpl, solenoid valve,55.400.16.805,kirloskar, expansion valve,55.400.17.e07,kcpl, safety v/v,kirloskar,kwf 160.14,13bar, safety v/v,kirloskar,kwf 160.14,16bar, core filter,kirloskar,kwf 160.14, oil filter,kirloskar,kwf 160.14, evd evol brd,56.137.50.611,kirloskar, expn ctlr,56.137.50.140,kirloskar, coil,55.400.17.sta.e7,kirloskar, elec exp v/v e7,55.400.17.e07,kirloskar, condenser assy,c12102d8012023d11m1,kcpl, oil sep assy,18.000.23.215.01,kcpl, screw comp,18.160.22.702,kcpl, butterfly vlv,55.400.12.125,kcpl, vpd,56.126.50.076,kcpl,kwk 265.24, sol valve kit,10.000.00.cxh,kcpl, valve solenoid,55.400.16.205,kcpl

CTN :41568088

13 Sep, 2025 NA

Kapurthala - Punjab

Tender For corrigendum : supply of steel almirah , steel almirah small , fully plastic moulded chair with arms seat andback cushioned , executive table or office table , library almirah steel glass front cabinet , laboratoryor libraryorcanteen table , drawing stool , computer table , computer and printer table , steel rack , conference room table , chemistry lab table , foot rest , laboratory table with boxes , lecture stand , laboratory table with drawers , notice board , single seat sofa , three seat sofa , revolving chair big , revolving chair small "steel almirah : size:- height-1981mm, width-916 mm, depth - 486mm construction: - the almirah should have welded type construction. the thickness of back panel should be 0.8 mm, other components the thickness should be 0.9mm and the shelf thickness should be 1.2 mm doors & handles: - the almirah should have full height steel hinged door & should be provided with handle. locking: - the almirah should be provided with 3 way locking mechanism & shooting bolt arrangement. shelves & load bearing capacity: - the almirah should have height wise adjustable shelf mounting and uniformly distributed load capacity per each full shelf should be 80 kg and shelves should be 4 in number and should be fully adjustable. powder coating process: - all the metal parts shall be given antirust surface treatment & and shall be powder coated with epoxy polyester powder. it shall involves an 8 step treatment. final finish shall consists of poxy polyester powder coating of approved color & shade with a dry film thickness of minimum 40 microns. the testing of paint shall be done for various physical & chemical properties as per is: 101. the material shall then be oven baked with a ) /bid number : gem/2025/b/6561795 * /dated: 25-08-2025 & & / bid document 1 / 35 controlled temperature of 1800c to 2000c. manufacturer/ supplier must have iso- 9001, 14001, bifma & ohsas certifications. certificates should be attached. leveler:-it should have leveler with m10 screw type leveler with hexagonal plastic base. ", "steel almirah small : size:- height 1270 mm, width 765mm, depth 440 mm construction: - the almirah should have welded type construction. the thickness of back panel should be 0.8 mm, other components the thickness should be 0.9mm and the shelf thickness should be 1.2 mm doors & handles: - the almirah should be provided with full height steel hinged door & should have handle. locking: the almirah should have 3 way locking mechanism with shooting bolt arrangement. shelves & load bearing capacity: - the almirah should have height wise adjustable shelf mounting and uniformly distributed load capacity per each full shelf should be 80 kg maximum and shelves should be 3 in number and should be fully adjustable shelves. powder coating process: - all the metal parts shall be given antirust surface treatment & and shall be powder coated with epoxy polyester powder. it shall involves an 8 step treatment. final finish shall consists of poxy polyester powder coating of approved color & shade with a dry film thickness of minimum 40 microns. the testing of paint shall be done for various physical & chemical properties as per is: 101. the material shall then be oven baked with a controlled temperature of 1800c to 2000c. manufacturer / supplier must have iso- 9001, 14001, bifma & ohsas certifications. certificates should be attached leveler:- it should have leveler with m10 screw type leveler with hex plastic base ", "fully plastic moulded chair with arms (seat &back cushioned) : size - total height : 820mm + 10mm, total width : 565mm + 10mm, total depth : 565mm + 10mm &total weight: 4.20 kg + 50gms cushioned chair with arms comprising of single piece moulded frame made of polypropylene & coated with pu coating paint high gloss finish with seat & back cushion made of moulded pu foam and velvet upholstery. weight of moulded polyproplene frame is 4.2

Trust

CTN :41742174

15 Sep, 2025 NA

Shirdi - Maharashtra

Tender For purchase of equipment- study of led array interfacing to avr and program to display various patterns on led array. ,study of event counter using opto-interrupter and ssd ,study of event counter using opto-interrupter and ssd. ,study of intrusion detection security system using ir/pir sensor and buzzer. ,study of ssd interfacing and writ program for rolling display. ,study of interfacing thumb wheel switch to avr and display input data on ssd. ,study of 16*2 lcd interfacing and its programming. ,study of traffic light controller using avr. ,study to control devices using smart phone & bluetooth module hc05. ,study of stepper motor interfacing and write a program for clockwise and anticlockwise ,rotation of motor. ,study of dc motor interfacing and write a program to vary speed of dc motor using pwm. ,study of interfacing lm35 sensor to on chip adc of avr and display temperature on lcd. ,study of light intensity measurement using ldr sensor and avr. ,study to interface of dht11 and programming using avr. ,study of waveform generations using dac and avr,of the mponent ,digital multimeter ,pn- junction diode ,zener diode ,ir sensor module ,bluetooth module ,digital ic ,ldr ,resistor-100 2 ,resistor-220 2 ,resistor-330 2 ,resistor-1 ,resistor - 2 ,resistor - 10 ,led - red ,led - yellow ,led - green ,led - white ,led - blue ,wires (single thread - bread board wires) ,battery (multimeter) ,rj 11 connector ,rj 44 connector ,rj 45 connector ,component box

Tongue Terminal End Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

State Government

Central Government And Public Sector

Central Government/Public Sector

Trust