Latest tool kits Tenders | Government tool kits Tenders

CTN :43563273

23 Jan, 2026 2.72 Lacs

Ramgarh - Jharkhand

Tender For supply of laboratory equipments e e -blow lamp brass 0.5 ltr capacity , pipe vice cast iron with hardened jaw open type 100mm , scissor blade ss 200mm , scissor blade ss 150mm , crimping tool 1 sqmm to 16 sqmm , crimping tool 16 sqmm to 400 sqmm , tweezers 150mm , drill s.s. twist block 2 mm , drill s.s. twist block 5 mm , drill s.s. twist block 5.8 mm , copper bit soldering iron 0.25kg , de soldering and soldering station , thermometer digital 0 to150c , knife switch dpdt fitted with fuse terminals 16a , knife switch tpdt fitted with fuse terminals 16a 440v , earth plate 60cmx60cmx3.15mm copper plate , earth plate 60cm x 60cm x 6mm gi plate , discrete component trainer with regulated power supply , hrc fuse , glass fuse , rewire type fuse , rheostat sliding type 0 to 100 ohm 2amp , rheostat sliding type 0 to 300 ohm 2amp , hp mercury vapor lamp , rectangular copper bus bar 19mm x 63mm x 0.25mtr , rubber mat 4ft wide x 7ft length x 17mm thickness , ammeter mc analog portable box type 0-5 a , energy meter 1phase 2 wire 230v 10a 50hz , energy meter 3phase 4 wire 415v 40a 50hz , power factor meter digital 440v 20a 3 phase , resistance type starter for ac motor upto 5 hp , star delta starter fully automatic for motor upto 12.5 hp , oscilloscope dual trace 20mhz , temperature controlled soldering iron 50w 230v , electrical induction plate 1500 watt 240v , electrical kettle 1500 watt 240v , electric iron automatic 750w 240v , geyser storage type 10 litre , mixer and grinder 750 watt 240v , washing machine semi automatic 5 kg , extendable ladder 7.5 m , platform step ladder foldable al anodised , portable welding machine 230v input , inverter 900va for 200ah 12v vrla battery , battery vrla 12v 200 ah , power sprayer 15l capacity , hand held bush and grass trimmer petrol , angle grinder 230v ac input , voltage stabilizer 500va ) /bid number : gem/2026/b/7104327 * /dated: 13-01-2026 & & / bid document 1 / 44

Central Government/Public Sector

CTN :42901010

20 Jan, 2026 NA

Koraput - Odisha

Tender For bid to ras tender for supply of procurement for maintenance tool kit for overhaul and test house : :-- hand drill machine with tool kits power 600 w min voltage 220 v 4dot5 a rpm 0 to3000 rpm min max impact rate no load 0 to 47000 bpm min drill size upto 13 mm , box spanner with ratchet 01 nos each size 8 mm to 32 mm all size , allen key set inch 01 nos each size 1by16 inch 5by64inch 3by32inch 1by8inch 5by32inch 3by16inch 7by32inch 1by4inch 5by16inch & 3by8inch , combination plier size 6inch 8inch 01 no each , ball pein hammer 400 gm min 800 gm min 01 no each , neon tester length 100to140 mm , adjustable spanner 10inch 15inch 01 no each , spanner double open end type 01 nos each size 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x27 25x28 32x36 36x41 46x50 55x60 , spanner double end ring type 01 nos each size 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x27 25x28 32x36 36x41 46x50 55x60 , hand held welding screen size 9inch x 16inch

Central Government/Public Sector

CTN :43532392

09 Feb, 2026 NA

Delhi - Delhi

Tender For supply of dead weight pressure gauge tester (along with all standard accessories and tool kits) as per annexure a of make/brand-ravika / yantrika /presto or similar [ warranty period: 30 months after the date of delivery ]

CTN :43428668

17 Jan, 2026 NA

Palai - Kerala

Tender For purchase of consumables - department of electronics engineering, wire (1sq.mm. coil) red, wire (1sq.mm. coil) black, wire (1sq.mm. coil) green, bulb(filament)-40w, bulb(filament)-60w, bulb(filament)- 100w, straight batten holder, switch-one way, bread board, capacitors-0.22 f (400v), capacitors-0.47 f (400v), capacitor(disc)-100pf, capacitor(disc)-220pf, capacitor(disc)-330pf, capacitor(disc)-470pf, capacitor(disc)-0.1 f, capacitor(disc)-0.01 f, db3(diac), diode-1n 4007, fet-bfw 10, ic 7400, ic 7402, ic 7411, ic 7432, ic 7447, ic 7446, ic 7473, ic 7474, ic 7476, ic 7483, ic 7486, ic 7490, ic 7493, ic 74150, ic 74151, ic 555, ic 565, ic 741, ic- ad 534, ic-ad 633, ic-cd 4046, ic-lm 311, ic-lm 324, ic-lm 380, ic- lm 723, ift, resistors-1.2k (0.5w), resistors-1.5k (0.5w), resistors-2.2k (0.5w), resistors-4.7k (0.5w), resistors-56 ohm(0.5w), resistors-1k (0.5w), resistors-10k (0.5w), scr-2p4m, single strand wire(22 swg), transistor-bc 107, transistor-bc 194 b, ujt- 2n2646, battery water, battery 9v, combination plier(210 mm), insulation tape, paper cutter blade(18 mm) (1 box), thinner(sp 58 nc), 2 pin chord wire, solder 60/40, linear potentiometer (10k), linear potentiometer 100k, linear potentiometer 4.7k, linear potentiometer 1m, linear potentiometer 22k, led (red), led (green), led (blue), led (yellow), hdmi cable (1.5 meter), 2 pin chord wire (1 .5meter), solder 80g (60/40), insulation tape (nc), transistor (bc548), transistor (bc 547), wire stripper (), resistor (270 ohm,0.5w), resistor (1k,0.5w), resistor (10k,0.5w), resistor (120k,0.5w), linear potentio meter (10k), linear potentio meter (100k), linear potentio meter (4.7k), linear potentio meter (1meg), linear potentio meter (22k), ic (741), ic (7805), ic (cd4016), capacitor (2200mf,50v), capacitor (0.01mf), capacitor (0.1mf), led (red), led (green), led (blue), single strand hook up wire (23awg/coil), digital ic (7400), digital ic (7402), digital ic (7404), digital ic (7408), digital ic (7432), digital ic (7486), digital ic (7410), digital ic (7411), digital ic (7420), digital ic (7421), digital ic (7473), digital ic (7474), digital ic (7476), digital ic (7490), digital ic (7493), digital ic (74154), digital ic (74151), digital ic (7483), ppt slide changer with laser pointer (2.4g hz), pen drive (64gb), crimping tool, rj 45 connector, rj 45 cable tester, extension board (4-way), department of electrical and electronics engineering, capacitor bank: 10 kva 440 v 3 phase, capacitor: 60 mfd 440 v, capacitor: 50 mfd 440 v, 3 pin plug: 5a, 250v, pvc wire: 1.5 sq. mm, contact switch: 4 pole 15a 250v nc, surge protective device dc 270v 20ka, surge protective device ac 270v 20ka, 3core wire 1.5 sq. mm, capacitor: 33 mfd, capacitor: 10 mfd, resistor: 820 ohm, resistor: 1.5 kilo ohm, push button nc, push button no, floating switch, soldering lead, relay, buzzer, wire: single stranded, dc motor, battery, npn transistor, cro probe, ic 7476, ic 7410, mercury, cotton waste, thinner, diesel, department of instrumentation engineering, arduino uno, raspberry pi 5 with - 16gb,bcm2712 2.4ghz quad-core 64-bit arm cortex-a76 cpu,2 usb 2.0 ports, 2 usb 3.0 ports, bluetooth 5.0 / bluetooth low energy (ble),gpio standard 40-pin gpio header, video and sound 2 micro hdmi ports (up to 4kp60 supported), 4-pole stereo audio and composite video port, on board ports 1 x dsi, 1 x ethernet, 2 x micro hdmi, 2 x usb 2.0, 2 x usb 3.0, 40-pin 2.54 mm (2 20 strip) gpio, usb type-c port, micro sd card slot - supports high-speed sdr104 mode and raspberry pi 5 case-red-white, micro sd card 32gb, power supply and memory card reader., ir sensor module, pir sensor module, ultra-sonic sensor module, heat sensor module, temperature and humidity sensor module, blue tooth module, mq 3 air quality/gas detector module, ultrasonic sensor module, motor driver module- l298, buzzer, colour recognition sensor module, desoldering pump, battery 9v, diode 1n 4007, ujt 2n2646, regulator ic - 7805, regulator ic - 7809, regulator ic

State Government

CTN :43537429

16 Jan, 2026 NA

Multi City - Tripura

Tender For procurement of hydraulic crimping tool with foot pump at gas thermal power station, rokhia

Central Government/Public Sector

CTN :43521921

30 Jan, 2026 NA

Amritsar - Punjab

Tender For supply of crimping tool cat6a , optical power meter , screw driver set , laser light sources with lc connector , fibre patch cord 2m , fibre patch cord 5m , cat6a utp patch cord 2m , cat6a utp patch cord 5m , pdu fuse 16amp , io cat6a , 1m face plate for cat6a io 1 , slide changer , 32 gb pendrive , wireless mouse , 64gb pendrive , tonner scanner device , lable printer , 16gb ram ddr4

CTN :43487185

21 Jan, 2026 NA

Hyderabad - Telangana

Tender For supply of eletrical integration tools d d ? g? g -crimp tool with positioner , crimp tool with head , 1553 crimping tool with head and positioner , retention tester with tool , nicomatic tool with die set , positioner locators , micro d locator pin and socket , soft cutter , thermal shunt , mechanical stripper , hard cutter , hot air blower with smoke observer , thermal stripper , ground lug crimping , ultrasonic cleaner with dispenser , butt splice crimping , soldering station with stand and magnifier , round and half round nose plier with tie gunround and half round nose plier with tie gun , power meter

CTN :43378478

16 Jan, 2026 6.00 Lacs

Kaushambi - Uttar Pradesh

Tender For supply of tool equipments d d - blacksmithy forge with open hearths , wrought iron anvils , blower with accessories motor switch etc , bench vice , accessories like calipers v blocks height gauges steel rule and scribers , scales , tool kits taps dies drills number punch letter punch rules and scribers , tool kits chisels hammers files hacksaw , hammer , hacksaw , bench drilling machine 3 phase , hand drill machine , chain wrenches , bench grinder , ring spanner set , pipe bending device , bimetallic thermometer , energy meter , watt meter , manometers , resistance thermometer , pneumatic valve

Central Government/Public Sector

CTN :43379215

20 Jan, 2026 NA

Rupnagar - Punjab

Tender For supply of synthetic water soluble cutting coolent , end mill parallel shank , jute mat , welding electrode for mild steel , welding electrode for stainless steel , white board and chalk board , ball pin hammer , industrial air blow gun, recoil hose , pneumatic push type connector , multipurpose plastic container box , lock medium size , power cable , black paint , mild steel plate , aluminium plate , mcb 4 pole , mcb 2 pole , aluminium solid rod with dia 25mm , gi sheet roll , mild steel bar , metal clamping kit , parallel blocks packing , hss drill , solid carbide end mill parallel shank , er 32 collet set , lathe turning cnmg 120408 pc 8125 hardness 50-60 hrc inserts , milling inserts , lathe centre drill with body , screw driver kit , nose plier , coolant pipe milling flexible long , insize precision vice jaw opening , led bulb , power hacksaw blade , clay graphite crucible for metal melting , sliding plastic file transperent cover , glue stick , garbage bag black pack , hss tap and die , tig copper filler wire with wire , mig torch cap , mig copper contact tip , co2 gas regulator with pre heater and flow meter , argon or co2 mig tig flow meter gas regulator gauge welding weld , mini soft wire snips nippers micro cutter , mallet hammer , wooden mallet , tin heavy duty cutter for sheet metal , chipping hammer for welding , trammel gauge , combined mortise and marking gauge , oil can dispenser , measuring jug , broken bolt screw extractor remover set easy out drill bits tools kits , hand held power punch sheet metal hole punch kit , examination gloves nitrile , files smooth cut with handle hand file flat , files smooth cut with handle hand file square , files smooth cut with handle hand file half round , files smooth cut with handle hand file rectangular , blue premium plastic storage bin , standard ceramic cap for tig torch , mini die grinder ) /bid number: gem/2025/b/7014071 * /dated: 30-12-2025 & & / bid document1 / 67